XM Satellite Radio R-672 manual Troubleshooting Guide, Problem Possible Cause Remedy

Page 54

R-672(A) 2007.6.15 10:17 AM 페이지 54

ENGLISH

Troubleshooting Guide

If a fault occurs, run through the table below before taking your receiver for repair.

If the fault persists, attempt to solve it by switching the receiver off and on again. If this fails to resolve the situation, consult your dealer. Under no circumstances should you attempt to repair the receiver yourself. This could void the warranty.

 

 

 

PROBLEM

POSSIBLE CAUSE

REMEDY

 

 

 

No power

• The AC input cord is disconnected.

• Connect cord securely.

 

• Poor connection at AC wall outlet or the outlet is

• Check the outlet using a lamp or another

 

dead or off.

appliance.

 

 

 

No sound

• The speaker wires are disconnected.

• Check the speaker connections.

 

• The master volume is adjusted too low.

• Adjust the master volume.

 

• The MUTE button is pressed to ON.

• Press the MUTE button to cancel the muting effect.

 

• Incorrect selection of input source.

• Select the desired input source correctly.

 

• Incorrect connections between the components.

• Make connections correctly.

 

 

 

No sound from the surround

• Surround mode is switched off(stereo mode).

• Select a surround mode.

speakers

• Master volume and surround level are too low.

• Adjust master volume and surround level.

 

• Monaural source is used.

• Select a stereo or surround source.

 

• Surround speaker setting is "N" (None).

• Select the desired surround speaker setting.

 

 

 

No sound from the center

• Dolby Virtual Speaker, stereo mode, etc is

• Select the desired surround mode.

speaker

selected.

 

 

• Center speaker setting is "N" (None).

• Select the desired center speaker setting.

 

• Master volume and center level are too low.

• Adjust master volume and center level.

 

 

 

No sound from the surround

• The input signal format or the current surround

• Under the proper situations, perform the 7.1(or

back speakers

mode cannot support the 7.1(or 6.1) surround.

6.1) surround playback.(For details, refer to

 

 

"ENJOYING SURROUND SOUND" on page 20.)

 

• Master volume and surround back level are too low.

• Adjust master volume and surround back level.

 

• Surround back speaker setting is "N" (None).

• Select the desired surround back speaker setting.

 

 

 

Stations cannot be received

• No antenna is connected.

• Connect an antenna.

 

• The desired station frequency is not tuned in.

• Tune in the desired station frequency.

 

• Antenna is in wrong position.

• Move antenna and retry tuning.

 

 

 

Preset stations cannot be

• An incorrect station frequency has been memorized.

• Memorize the correct station frequency.

received

• The memorized stations are cleared.

• Memorize the stations again.

 

 

 

Poor FM reception

• No antenna is connected.

• Connect an antenna.

 

• The antenna is not positioned for the best reception.

• Change the position of the antenna.

 

 

 

Continuous hissing noise during

• Weak signals.

• Change the position of the antenna.

FM reception, especially when a

 

• Install an outdoor FM antenna.

stereo broadcast is received.

 

 

 

 

 

Continuous or intermittent

• Noise is caused by motors, fluorescent lamps or

• Keep the receiver away from noise sources.

hissing noise during AM

lightning, etc.

 

reception, especially at night.

 

• Install an outdoor AM antenna.

 

 

 

Remote control unit does not

• Batteries are not loaded or exhausted.

• Replace the batteries.

operate.

• The remote sensor is obstructed.

• Remove the obstacle.

 

 

 

54

Page 53 Page 55
Image 54
Page 53 Page 55
Contents CoverA2007.6.15957AM페이지 Safety Instructions Introduction Read this Before Operating Your UnitContents Connecting Antennas System ConnectionsConnecting Video Components HDMIHigh Definition Multimedia Interface connectionConnecting Audio Components Connecting External INS Connecting Digital INS and OUTDigital input default settings Connecting Speakers Connecting Subwoofer PRE OUTConnecting XM only for North America Surround back speakersSwitched AC Outlets AC Input CordFront Panel Controls Fluorescent DisplaySetup MIC Jack AUX in JackVideo 3 in Jacks Remote Controls Remote Control Operation Range Loading BatteriesWhen selecting the External in as desired OperationsBefore operation When CD, AUX, Video 1~2 is selected as an input source Operate the selected component for playbackAdjusting the tone bass and treble Surround Sound Dolby Virtual Speaker Dolby Pro Logic IIx surroundDolby Pro Logic II surround Dolby Pro LogicSignal format being input Selectable surround mode Enjoying Surround SoundTo cancel the surround mode for stereo operation 2CH downmix modeDolby Pro Logic II/Dolby Pro Logic IIx Music Parameters Dolby Virtual Speaker ParametersAdjusting each channel level with test tone Dolby Headphone ParametersAdjusting the current channel level Memorizing the adjusted channel levels Recalling the memorized channel levelsAuto presetting Auto tuningManual tuning Listening to Radio BroadcastsTuning to preset stations Manual presettingMemory Backup Function Scanning preset stations in sequenceXM Satellite Radio only for North America Signing up for XM Satellite RadioChannel search Direct searchCategory search Error message and status Presetting channels Preset searchSignal strength display mode Displaying XM informationRecording with Tape Dubbing the audio and video signals separately onto VideoRecording Dubbing from video components onto VideoDigital Audio Recording with MD Recorder Optical Digital OUTOther Functions Operating the sleep timerAdjusting the brightness of the fluorescent display Displaying the operation statusSystem Setup Navigating through the setup menuSetup menu flow English Setting the System When selecting the AMP AssignWhen selecting the Subwoofer mode When selecting the Tone When selecting the Cinema EQSetting the Input When selecting the DigitalWhen selecting the Remaster When selecting the Video ModeWhen selecting the Auto Surround When selecting the AV SyncSetting the Speaker Setup When selecting the Auto SetupAbout the first listening position PreparationsEnglish When selecting the Speaker Configuration When setting the speaker size by performing the auto setupWhen setting the distance When selecting the Speaker DistanceWhen selecting the desired unit About the speaker sizeWhen selecting the Speaker Crossover About the crossover frequencyWhen selecting the Room EQ Setting the CH Level Adjusting the current channel levelRecalling the memorized channel levels Setting the Sound Parameter When selecting the Night ModeWhen selecting the C. Width Center width control When selecting the Dolby Plii MusicWhen selecting the Pano Panorama mode When selecting the Dimen Dimension controlWhen selecting the Dolby Headphone When selecting the Dolby Virtual Speaker When selecting the REF Dolby Virtual Speaker Reference modeWhen selecting the Wide Dolby Virtual Speaker Wide mode Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier SectionCoverA2007.6.15957AM페이지
Top Page Image Contents