Maytag MGR6875ADB/Q/S/W manual Oven Door Hinge, Regulator, Gas Valve, Door Plunger, Spark Module

Page 28

Disassembly Procedures

!WARNING

To avoid risk of electrical shock, personal injury, or death: disconnect electrical and gas supply before servicing.

Oven Door Hinge

NOTE: Removal of range from installation position is required.

1.Disconnect power before servicing.

2.Remove oven door, see "Oven Door(s)-Door Removal" procedure.

3.Remove maintop, see "Maintop Removal" procedure. (Perform steps 1 – 6.)

4.Remove appropriate side panel (left or right), see "Side Panel" procedure.

5.Remove screws securing hinge to front frame flange.

6.Complete hinge assembly may be removed.

7.Reverse procedure to reassemble.

NOTE: The door hinges are colored coded for ease of installation. The upper spring hook is gold and the lower spring hook is white.

Regulator

NOTE: Removal of range from installation position is required.

1.Disconnect power before servicing.

2.Slide range forward out of installation position to gain access to components.

3.Disconnect tubing from regulator.

4.Remove screws securing bracket to back of unit.

5.Remove screws securing regulator to support bracket.

6.Reverse procedures to reassemble.

NOTE: When reconnecting supply line to regulator use pipe dope compound to seal the connection.

NOTE: Perform gas leak test.

Gas Valve

NOTE: Removal of range from installation position is required.

1.Disconnect power before servicing.

2.Remove range from installation position, see "Move and/or Replacing Range" procedure.

3.Remove screws securing bottom rear access panel to chassis.

4.Remove screws securing top rear access panel to chassis.

5.Disconnect tubing from gas valve.

6.Disconnect and label wire terminals from gas valve.

7.Remove screws securing gas valve to chassis.

8.Reverse procedures to reassemble.

NOTE: Perform gas leak test.

Door Plunger

NOTE: Removal of range from installation position is required.

1.Disconnect power before servicing.

2.Remove range from installation position, see "Move and/or Replacing Range" procedure.

3.Remove maintop, see "Maintop Removal" procedure. (Perform steps 1 – 6.)

4.Remove right side panel, see "Side Panel" procedure.

5.Disconnect and label wire terminals from door plunger switch.

6.Open oven door and remove screws securing door plunger to the front of the oven cavity.

7.Reverse procedures to reassemble.

Spark Module

NOTE: Removal of range from installation position is required.

1.Disconnect power before servicing.

2.Remove range from installation position, see "Move and/or Replacing Range" procedure.

3.Remove screws securing bottom rear access panel to chassis.

4.Remove screws securing top rear access panel to chassis.

5.Label and disconnect wire terminals from spark module.

6.Remove spark module from secured position.

7.Reverse procedures to reassemble.

Convection Assembly

(Model MGR6875AD*)

1.Disconnect power before servicing.

2.Remove oven door, see "Oven Door(s)-Door Removal" procedure.

3.Remove oven racks from oven cavity.

4.From inside the oven cavity (center-rear), remove screws securing assembly shroud or ring-cover.

5.Remove screws securing assembly to cavity.

6.Remove by gently rotating assembly until enough clearance is established between assembly, cavity wall and wire terminals/connectors.

7.Disconnect and label wire terminals from heat element and assembly (connector block).

8.Remove assembly from cavity.

9.Reverse procedures to reassemble.

28

16023415

©2004 Maytag Services

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Service Customer Service Support Center Important InformationTable of Contents Safety Practices for Servicer ServicingUsing the Oven Receiving OvenConnecting Range to Gas Product Safety DevicesBaking, Broiling, and Roasting Electrical RequirementsGeneral Information Specifications Placement of the OvenService Parts and AccessoriesArning GroundingRange Description Troubleshooting Procedures 16023415 Maytag Services Maytag Services 16023415 Component Troubleshooting No gas flows to burner Ignitor glows red Check lamp and replace is necessary Testing Procedures Testing Procedures Illustration/Component Test Procedure H2 Control Testing Model MGR6875AA H3 Control Testing Model MGR6775AA Quick Test Mode for Electronic Range Control This mode will also display the current fault code for Top Surface Valve and Spark Switch Top Burner Lower AssemblyMoving and/or Replacing Range Leveling LegsOven Light Replacement Oven SensorElectronic Clock Oven DoorsGasket and Door Disassembly Lower Latch Assembly Upper Latch AssemblyConvection Assembly Oven Door HingeRegulator Gas ValveOven Cavity Components Gas Oven RacksRack Positions Appendix a Maytag Double Oven Gas Range Double Oven Gas Range Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Installation Instructions Appendix B Suggested Heat Settings Operating During a Power FailureSurface Controls Pilotless IgnitionSurface Cooking To prevent the cooktop from discoloring or stainingTo change the clock to 24-hour format To set the ClockTimer Fault CodesAdjusting the Sound Level Locking the Control Oven DoorsReturn To Factory Default Settings Setting Upper and Lower Oven Functions BakingCook & Hold To set bakeDelay Cook & Hold Adjusting the Oven Temperature To cancel Keep WarmTo adjust the oven temperature Keep WarmBroiling upper oven only To set BroilAutomatic Shut-Off/Sabbath Mode Oven VentOven Lights Oven BottomUpper oven Lower ovenTo remove oven racks To replace oven racksSurface Cooking Surface Cooking Control Panel Using the TouchpadsClock Adjusting Sound Level Baking with Convection Setting Oven FunctionsTo set Convect Bake Roasting With Convection To set Convect RoastBroiling Chart Broil times are based on a 5 minute preheat Broiling upper oven onlyOven Cooking Favorite To cancel a Favorite cycle in progressTo start a cycle programmed into Favorite Sabbath Mode Notes Rack Positions lower oven Care & Cleaning Do not USE ANY Cleaning Product Containing Chlorine Bleach Appendix C LP Conversion Instructions LP Conversion Instructions LP Conversion Instructions LP Conversion Instructions
Top Page Image Contents