Briggs & Stratton 01897-0 owner manual Disconnect Box Mounting Guidelines, Fuel Inlet Dimensions

Page 11

Briggs & Stratton Power Products Standby Generator

Installation, Start-Up and Owner’s Manual

Disconnect Box Mounting Guidelines

The disconnect box is a NEMA Type 3R enclosure suitable for outdoor use.

Guidelines for mounting the disconnect box include:

•The disconnect box must be installed with appropriate hardware for conduit connections.

•Install the disconnect box on a firm, sturdy supporting structure, making sure it is level and plumb.

•NEVER install the disconnect box where any corrosive substance might drip onto the enclosure.

•Protect the disconnect box at all times against excessive moisture, dust, dirt, lint, construction grit and corrosive vapors.

The typical installation of the disconnect box is depicted in Figure 3. Discuss layout suggestions/changes with the owner before beginning the installation process.

Figure 3 — Typical Disconnect Box Mounting

Fuel Inlet Dimensions

Figure 4, below, depicts the location of the fuel piping connector.

Figure 4 — Generator Fuel Attachment Location

Fuel Piping

Connector

4.5”

3/4” NPT

13.5”

Removable Roof and Access Door

The Standby Generator is equipped with an enclosure that has a removable roof and an access door for the control panel.

To Remove Roof:

Remove the four screws and lift off.

To Remove Access Door:

1.Remove roof as described above.

2.Remove screw at top of access door.

3.Pull access door outward (away) from unit while pulling door upward and out of base. Door will come free of generator enclosure.

To Install Access Door and Roof:

1.Guide bottom of access door into base.

2.Push access door until it is flush with sides.

3.Replace door screw.

4.Replace roof and screws.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Installation Start-Up Table of Contents Wear protective goggles, rubber apron, and rubber gloves Safety RulesBriggs & Stratton Power Products Standby Generator Customer Responsibilities Installer ResponsibilitiesInstallation Assistance IntroductionOil Fill BatteryKnow Your Standby Generator AUTO/OFF/MANUAL Know Your Control PanelOwner Orientation Installation ProceduresStandby Generator Location Shipment ContentsRequired Specialty Tools/Equipment Lifting the GeneratorDevice Running Watts Essential Circuit SelectionDisconnect Box Mounting Guidelines Fuel Inlet DimensionsRemovable Roof and Access Door Standby Generator unit has been factory set to Gaseous Fuel SystemLoad Fuel ConsumptionFrom Fuel 10ft 15ft 20ft 30ft 40ft 50ft 60ft 70ft 80ft 90ft 100ft Fuel Pipe SizingWithdrawal Rate 32F 20F 10F 30F 40F Fuel Comparison ChartPhysical Properties Propane Natural Gas Generator Control Circuit Connection To install the remote LED plateGenerator AC Connection System Grounding the GeneratorEngine Oil Battery ConnectionBefore Initial START-UP Fuel System SelectionAutomatic Operation Sequence Initial START-UP no LoadTo perform the Set Exercise procedure Setting Exercise TimerInstallation Inspection Servicing the System SpecificationsFault Detection System Automatic OperationEngine Fail To Start Number of LED Flashes Fault DescriptionReset Fault Detection System No LED Discharged BatteryChanging Oil Filter Generator MaintenanceChanging Engine Oil and Filter Changing OilStorage To Clean the GeneratorWhen Calling the Factory Problem Cause Correction TroubleshootingBriggs & Stratton Power Products Standby Generator Schematic Wiring Diagram Exploded View Main Unit KIT, Deflector Muffler Assy w/ Hrdwr Parts List Main UnitDescription Items Not IllustratedExploded View Enclosure Cradle Parts List EnclosureExploded View Control Panel Parts List Control Panel SCREW, M5 .8 x 10 Taptite Exploded View and Parts List AlternatorHARNESS,Wire DC Charge ADAPTER, Mounting,AlternatorYear Consumer Use Years Years orSistema DE Combustible Gaseoso Tabla DE ContenidoManual de Instalación,Arranque y Propietario Conozca EL Panel DE Control Orientación Para EL PropietarioAdvertencia Instrucciones DE SeguridadPeligro Precaución Asistencia para la instalación IntroducciónResponsabilidades DEL Cliente Responsabilidades DEL InstaladorTapón de Llenado y Varilla de Nivel de Aceite Permite Conozca SU Generador DE ReservaEtiqueta del Motor Tapón de Llenado y Varilla De Nivel de AceiteFusible de 15 Amperios Protege los circuitos de control de Conozca EL Panel DE ControlFusible de Disyuntor InterruptorProcedimientos DE Instalación Orientación Para EL PropietarioCircuitos Fundamentales Contenido de la CajaElevación del Generador Ubicación del Generador de ReservaDispositivo Vatiaje de Selección de los Circuitos FundamentalesTecho y Puerta de Acceso Desmontables Dimensiones de la Entrada de CombustibleDirectrices de Montaje del Cuadro de Desconexión El generador de reserva viene preparado de fábrica para Sistema DE Combustible Gaseoso AdvertenciaGas Natural Vapor de PL Consumo de CombustiblePropano Líquido PL peso específico = Dimensiones de la Cañería de CombustibleGas Natural peso específico = Tasa de consumo 32F 20F 10F 30F 40F Cuadro de Comparación de CombustiblesPropiedades físicas Propano Gas natural Placa de LED Remoto Sistema de Conexión de c.a. del GeneradorConexión a Tierra del Sistema Interconexiones del Circuito de ControlSistema de Suministro de Combustible Antes DEL Arranque InicialSelección DEL Sistema DE Combustible Aceite de MotorFije el interruptor AUTO/OFF/MANUAL en la posición Arranque Inicial SIN CargaSecuencia DE Operación Automática Instale el fusible de 15 Amperios en el panel de controlInspección Posterior a LA Instalación Ajuste DEL Temporizador DE EjercicioFallas EspecificacionesOperación Automática Sistema DE Detección DEBaja Presión de Aceite Cantidad de Destellos del LED Descripción de la FallaRestablecimiento del Sistema de Detección de Fallas No se Enciende el LED Batería DescargadaCambio del Aceite Mantenimiento DEL GeneradorCambio del Aceite del Motor y del Filtro Cambio del Filtro de AceiteSi Llama a la Fábrica AlmacenamientoPara Limpiar el Generador Reparacion DE Averias Garantía Limitada Table DES Matières Manuel dInstallation, Démarrage et UtilisateurAvertissement Règles DE SécuritéLe contact de ces pièces risque de causer de graves brûlures Responsabilités DE Lacheteur Responsabilités DE LinstallateurAide À Linstallation IntroductionFiltre à Air Et Jauge dHuile Filtre à lHuile FAMILIARISEZ-VOUS Avec Votre Génératrice D’ÉTAT D’ATTENTEDisjoncteur Interrupteur FAMILIARISEZ-VOUS Avec LE Tableau DE Commande15 Ampères Conseils AU Propriétaire Procédures DinstallationSoulèvement de la Génératrice Emplacement du Génératrice d’état d’AttenteContenu de la Boîte Outils/Équipements Spécialisés NécessairesAppareil Watts Sélection des Circuits EssentielsToit Amovible et Porte dAccès Dimensions de lOrifice dAdmission du CombustibleDirectives dAssemblage du Boîtier de Débranchement Le génératrice d’état d’attente a été réglé en usine pour LE Système DE Combustible Gazeux AvertissementGas Naturel Vapeur PL Consommation de CombustibleGaz de Pétrole Liquéfié GPL densité = 1,50 Grosseur du Tuyau de CombustibleGaz Naturel densité = 0,65 Poids† Indice d’octane Recherche 110+ Charte de Comparaison des CombustiblesPropriétés physiques Propane Gaz naturel Densité 36,39Mise à la Masse du Système Interconnexions du Circuit de CommandePour installer la plaque DEL à distance Système de Branchement C.A. de la GénératriceBranchement de la Batterie Avant LE Démarrage InitialSélection DU Système DE Combustible Huile à MoteurRéglez linterrupteur AUTO/OFF/MANUAL sur Manual Capteur de Prise en Charge de la Tension de ServiceDémarrage Initial Sans Séquence DE Fonctionnement AutomatiquePour Exécuter la Procédure de Réglage du Cycle dExercice Vérification InstallationRéglage DE LA Minuterie DU Cycle Dexercice Entretien du Système CaractéristiquesFonctionnement Automatique Système DE Détection DES PannesFaible Pression dHuile Clignotements Du VoyantRéarmement du Système de Détection des Pannes Aucun DEL Batterie déchargéeVidange de lHuile Entretien DU GénérateurChangement dHuile à Moteur et de Filtre Changement du filtre à huileCommunications avec le Fabricant RemisagePour Nettoyer le Générateur Dépannage Remarques Garantie Limitée
Related manuals
Manual 84 pages 42.1 Kb

01897-0 specifications

Briggs & Stratton 01897-0 is a popular engine model renowned for its performance and durability in various applications. It is primarily used in lawn mowers and other outdoor power equipment, making it an ideal choice for homeowners and landscaping professionals alike.

One of the standout features of the 01897-0 is its powerful engine. This model is equipped with a reliable four-stroke engine that provides robust power for optimal mowing efficiency. With a displacement of 500cc, it delivers a substantial amount of torque, making it suitable for handling thick grass and tough terrains effortlessly.

The engine design incorporates several advanced technologies aimed at improving performance and extending longevity. One such feature is the overhead valve (OHV) design, which enhances airflow and increases combustion efficiency. This results in better fuel economy and lower emissions, aligning with environmental standards while providing the power needed for demanding tasks.

Another notable characteristic of the Briggs & Stratton 01897-0 is its easy-starting system. The engine is designed with a recoil starter, which allows for a quick and effortless start-up. This is especially beneficial during busy mowing seasons when efficiency is paramount.

In terms of maintenance, the 01897-0 emphasizes user convenience. It features an accessible oil drain and replacement system, facilitating simple oil changes. The air filter can also be easily accessed and replaced, ensuring the engine maintains optimal performance for many years.

Furthermore, the engine is engineered for vibration reduction, enhancing user comfort during operation. This technology helps minimize fatigue, allowing for extended mowing sessions without discomfort. The lightweight design of the engine also contributes to easier maneuverability, making it a practical choice for users of all experience levels.

Finally, Briggs & Stratton is known for its commitment to quality, and the 01897-0 is no exception. It is built to withstand the rigors of outdoor use, ensuring reliability and durability even under challenging conditions. With a reputation for excellence and a proven track record, the Briggs & Stratton 01897-0 continues to be a preferred choice for those seeking performance and reliability in outdoor power equipment. Whether for residential or commercial use, this engine model remains a popular and trusted option for efficient lawn care.
Top Page Image Contents