Hoshizaki DCM-750BAH-OS, DCM-750BWH-OS service manual Problem Possible Cause Remedy

Page 40

Problem

Possible Cause

 

Remedy

 

 

 

 

[3] Ice purge cycle will

a) Water Control Relay

1. Low water safety

1. Replace.

not start.

 

circuit open

 

 

 

(bad contacts ).

 

 

b) Control Switch

1. Bad contacts.

1. Check for continuity and

 

 

 

replace.

 

 

 

 

 

c) Bin Control

1. Open.

1. Bin full, check for

 

 

 

continuity on proximity

 

 

 

switch.

 

 

 

 

 

d) Control Board

1. Fails to operate gear

1. See "II.D.4. Control Board

 

 

motor relay.

Check Procedure."

 

 

 

 

 

e) Gear Motor Fuse

1. Blown.

1. Check gear motor

 

 

 

amperage, bearing

 

 

 

wear (see "V.F.1. Upper

 

 

 

Bearing Wear Check"),

 

 

 

and supply voltage.

 

f) Gear Motor Thermal

1. Open.

1. Check gear motor

 

Protector

 

bearings, supply voltage.

 

g) Gear Motor

1. Open windings.

1. Replace.

 

 

 

 

 

 

2. Auger coupling broke.

2. Replace.

 

 

 

 

 

 

3. Locked bearings.

3. Replace.

 

 

 

 

[4] Freeze cycle will not

a) Gear Motor Protect

1. Open coil.

1. Replace.

start (compressor).

Relay

2. Open contacts.

2. Replace.

 

 

 

 

 

 

 

b) Control Board

1. Defective.

1. See "II.D.4. Control Board

 

 

 

Check Procedure."

 

 

 

 

 

c) Starter (Start Relay)

1. Bad contacts.

1. Check for continuity and

 

 

 

replace.

 

 

 

 

 

 

2. Coil winding open.

2. Replace.

 

 

3. Loose connections.

3. Tighten.

 

 

 

 

 

d) Start Capacitor or Run

1. Defective.

1. Replace.

 

Capacitor

 

 

 

 

 

 

 

e) Compressor

1. Power supply not

1. Refer to nameplate and

 

 

within specifications.

correct.

 

 

 

 

 

 

2. Wiring to compressor.

2. Check for loose or open

 

 

 

connection, repair or

 

 

 

replace.

 

 

3. Defective.

3. Replace.

 

 

 

 

 

 

4. Compressor locked

4. Replace.

 

 

and internal motor

 

 

 

protector tripped.

 

 

 

 

 

[5] All components

a) Refrigerant

1. Low charge.

1. See "V.B. Service for

run, but no ice is

 

 

Refrigerant Lines."

produced.

 

 

 

 

2. Refrigerant line or

2. Remove the restriction or

 

 

 

 

component restricted.

component and replace

 

 

 

the drier.

 

 

3. Air or moisture

3. Recover refrigerant,

 

 

trapped.

replace drier, evacuate,

 

 

 

and recharge.

 

 

 

 

 

b) Expansion Valve

1. Bulb loose.

1. Secure bulb.

 

 

 

 

 

 

2. Operating erratically.

2. Check and replace.

 

c) Compressor

1. Defective.

1. Replace.

 

 

 

 

40

Image 40
Contents DCM-750BAH DCM-750BAH-OS DCM-750BWH DCM-750BWH-OS Hoshizaki AMERICA, INC Contents Page Specifications Icemaker DCM-750BAHDCM-750BAH-OS Water TEMP. FDCM-750BWH Potable Water WATER-COOLED CondenserDCM-750BWH-OS Potable Water Water Cooled CondenserII. General Information Construction DCM-750BWH-OS Ice Making Unit Sequence of Operation Startup Control Board Control Board Layout DCM-750BAH, DCM-750BWH Control BoardDCM-750BAH-OS, DCM-750BWH-OS Features LED LightsControls and Adjustments Portion Control Control Board Check ProcedurePower Supply Ice Making ComponentsDispensing Components DCM-750BAH, DCM-750BWH Float Switch Inlet Water Valve DCM-750BWH-OS Wiring Diagrams Wire Color CodeDCM-750BAH-OS, DCM-750BWH-OS Sequence of Electrical Circuit Ice Making DCM-750BWH-OSIce Purge Cycle Orange WHITE/BLACK Pink WHITE/BROWN RED WHITE/BLUE Violet Hour Drain Cycle / Drain Switch Shutdown Low Water Safety High Pressure Switch Sequence of Electrical Circuit Dispensing Continuous DispensePortion Dispense Performance Data 192Approximate IV. Service Diagnosis Diagnostic Procedure Ice Production Check Diagnostic Charts No Ice ProductionProblem Possible Cause Remedy Problem Possible Cause Remedy Low Ice Production Other Dispensing Opti Serve OS Sensors 5b. Ice Dispensing Portion Mode 5a. Ice Dispensing Continuous Mode5c. Water Dispensing Removal and Replacement of Components Service for Refrigerant LinesRefrigerant Recovery BrazingEvacuation and Recharge R-404A Removal and Replacement of Compressor Removal and Replacement of Expansion Valve Removal and Replacement of Evaporator Assembly Components Removal and Replacement of Extruding Head Upper Bearing Wear CheckRemoval and Replacement of Auger Removal and Replacement of EvaporatorPage 5b. Lower Housing Removal and Replacement of Gear Motor Page Removal and Replacement of Water-Cooled Condenser Page Adjustment of Water Regulating Valve Water-Cooled Model Only Removal and Replacement of Fan MotorRemoval and Replacement of Inlet or Dispensing Water Valve Removal and Replacement of Drain ValveDispensing Auger and Agitator Removal and Replacement of Dispensing SystemDispensing or Agitating Motor Page VI. Cleaning and Maintenance Cleaning and Sanitizing InstructionsCleaning Solution Water SystemSanitizing Solution Dispensing ComponentsBin Control Bracket Snap Pin Maintenance Frequency Area TaskPreparing the Icemaker for Long Storage