GE JCB905, JCB968 owner manual Operation Checklist

Page 39

Installation Instructions

6FINAL INSTALLATION CHECKLIST

•Check to make sure the circuit breaker is closed (RESET) or the circuit fuses are replaced.

•Be sure power is in service to the building.

•Check to be sure that all packing materials and tape have been removed. This will include tape on metal panel under control knobs (if applicable), adhesive tape, wire ties, cardboard and protective plastic. Failure to remove these materials could result in damage to the appliance once the appliance has been turned on and surfaces have heated.

•Check to make sure that the door and drawer are parallel to each other and that both operate smoothly. If they do not, see the Owner’s Manual for proper replacement.

•Check to make sure that the rear leveling leg is fully inserted into the Anti-Tip bracket and that the bracket is securely installed.

7OPERATION CHECKLIST

•Turn on one of the surface units to observe that the element glows within 60 seconds. Turn the unit off when glow is detected.

If the glow is not detected within the time limit, recheck the range wiring connections. If change is required, retest again. If no change is required, have building wiring checked for proper connections and voltage.

•Check to make sure the Clock (on models so equipped) display is energized. If a series of horizontal red lines appear in the display, disconnect power immediately. Recheck the range wiring connections. If change is made to connections, retest again. If no change is required, have building wiring checked for proper connections and voltage. It is recommended that the clock be changed

if the red lines appear.

•Be sure all range controls are in the OFF position before leaving the range.

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Write the model and serial numbers here Model # Serial #All ranges can tip and injury could result Consumer Support Troubleshooting TipsSupport Safety InstructionsRadiant Surface Units Troubleshooting Tips Consumer CleaningOperating Instructions Care Consumer Support Temperature LimiterAbout the radiant surface units InstructionsSafety Instructions Operating Instructions Care and CleaningTroubleshooting Tips Hot surface indicator light will Using the surface unitsHow to Set Using the Bridge Burner on some modelsUsing the Warming Zone on some models Instructions OperatingFood Type Has been a power outage Using the oven controlsConsumer Support Troubleshooting Tips Care and Cleaning Programmed functions must be resetConsumer Support Care and Cleaning Troubleshooting TipsType of Food Preheating and Pan PlacementAluminum Foil Before you begin…HI Broil How to Set the Oven for BroilingSafety Broiling GuideHow to Set an Immediate Start and Automatic Stop Using the timed baking and roasting featuresSafety Instructions Consumer Support Troubleshooting Tips CareDo not store the probe in the oven Using the probe. on some modelsTroubleshooting Tips Consumer Support Instructions Operating Instructions Care and CleaningTroubleshooting Using the clock, kitchen timer and control lockoutType of margarine will affect baking performance Adjust the oven thermostat-Do it yourselfCleaning Troubleshooting Tips Consumer Support To Adjust the ThermostatTips Care and Cleaning Using the convection oven. on some modelsConvection Roast Care and Cleaning TroubleshootingHow to Set the Oven for Convection Baking or Roasting Tips Consumer SupportTouch the Convection Bake Safety Care and Cleaning Operating Instructions Safety Convection Roasting GuideTouch the Convection Roast pad How to Set the Oven For Warming on some models Using the proofing and warming featuresCleaning Troubleshooting Tips Consumer Support How to Set the Oven For Proofing on some modelsUsing the self-cleaning oven Before a Clean CycleHow to Set the Oven for Cleaning Care and Cleaning Troubleshooting Tips Consumer Support How to Delay the Start of CleaningAfter a Clean Cycle Special features of your oven control Consumer Support Troubleshooting TipsCare and Cleaning Instructions Operating Instructions Care and CleaningTone Volume Troubleshooting TipsHow to Set for Regular Baking/Roasting Using the Sabbath feature. on some modelsHow to Exit the Sabbath Feature Troubleshooting Tips Consumer SupportOperating Instructions Care and cleaning of the rangeConsumer Support Troubleshooting Tips CareLift-Off Oven Door Care and Cleaning Troubleshooting TipsCleaning the Oven Door Instructions Operating InstructionsStorage Drawer Removal Oven Light ReplacementConsumer Broiler Pan and GridStainless Steel Surfaces on some models Troubleshooting Tips ConsumerOven Floor Oven Racks and Convection Roasting RackHeavy, Burned-On Residue Cleaning the glass cooktopNormal Daily Use Cleaning Burned-On ResidueGlass surface-potential for permanent damage Troubleshooting TipsInstallation Instructions Prepare to Install the Range Install the Range Operation Checklist Looking For Something More? AccessoriesProblem Possible Causes What To Do Before you call for service…Food does not bake Oven temperatureToo hot or too cold Oven will not workDuring a clean cycle Clock and timerSee the Using the clock and timer section See the Using the self-cleaning oven sectionOr start time Control signals afterSee the Special features of your oven control section Power outageOwnership Registration Box Mississauga, Ontario L4Y 4G1 Consumer Product Ownership Registration GE Will Provide GE Electric Range WarrantyCare and Cleaning Safety Instructions Operating InstructionsRegister Your Appliance Consumer Support GE Appliances Website Schedule ServiceParts and Accessories Contact Us

JCB905, JCB968 specifications

The GE JCB968 and JCB905 are two powerful and efficient telehandlers that have made significant impacts in the construction, agricultural, and industrial sectors. Renowned for their reliability and versatility, these machines are designed to meet the demands of various heavy-duty applications.

The JCB968 is equipped with a robust engine that provides exceptional power and torque. It boasts a lifting capacity of up to 6,000 kg, making it suitable for lifting heavy loads, including pallets, materials, and equipment. The unit features a maximum lifting height of approximately 9 meters, allowing users to reach bins and heights that are otherwise difficult. One of the standout features of the JCB968 is its four-wheel drive system, which enhances traction and stability on uneven terrains. The machine also utilizes hydrostatic transmission, enabling smooth acceleration and precise control, essential for operators working in tight spaces.

Conversely, the JCB905 is notable for its compact design, making it ideal for confined job sites where space is at a premium. With a lifting capacity of 5,000 kg and an impressive reach of around 5.5 meters, the JCB905 is perfect for handling lighter materials while still offering excellent performance. Its tight turning radius allows for exceptional maneuverability, ensuring that operators can navigate through narrow aisles and work areas with ease.

Both machines leverage advanced hydraulic systems that improve efficiency and increase productivity. The JCB968 and JCB905 come equipped with various attachment options, such as forks, buckets, and winches, allowing for a wide range of applications from material handling to construction tasks. The cab design of both models enhances operator comfort and visibility, which is critical in ensuring safety and reducing fatigue during long working hours.

In terms of technologies, both telehandlers incorporate telematics systems that provide real-time data on machine performance, location, and health diagnostics. This allows for better fleet management and ensures that maintenance is carried out proactively, minimizing downtime.

Overall, the GE JCB968 and JCB905 are exemplary models that combine power, agility, and efficiency, making them indispensable assets in any operation requiring versatile handling capabilities. Their blend of modern technology and user-centric design stands as a testament to JCB's commitment to innovation and customer satisfaction.
Top Page Image Contents