GE JCB968 Control signals after, Or start time, Display goes blank, Display flashes, Power outage

Page 44

Support Troubleshooting Tips Care and Cleaning Operating Instructions Safety Instructions

Before you call for service…

Troubleshooting Tips

Problem

 

Possible Causes

What To Do

 

 

 

 

Control signals after

 

You forgot to enter a

• Touch the BAKE pad and desired temperature or

entering cooking time

 

bake temperature or

the SELF CLEAN STD/LO pad and desired clean time.

or start time

 

cleaning time.

 

 

 

 

 

Display goes blank

 

A fuse in your home may be

• Replace the fuse or reset the circuit breaker.

 

 

blown or the circuit

 

 

 

breaker tripped.

 

 

 

 

 

 

 

The clock is in the

• See the Special features of your oven control section.

 

 

black-out mode.

 

 

 

 

 

Display flashes

 

Power failure.

• Reset the clock.

 

 

 

 

Unable to get the

 

Oven control pads were

• The BROIL HI/LO and BAKE pads must be touched at

display to show “SF”

 

not touched properly.

the same time and held for 3 seconds.

 

 

 

 

“Probe” appears in

 

This is reminding you to

• Enter a probe temperature.

the display

 

enter a probe temperature

 

(on some models)

 

after plugging in the probe.

 

 

 

 

 

Power outage,

 

Power outage or surge.

• Reset the clock. If the oven was in use, you must reset

clock flashes

 

 

it by touching the CLEAR/OFF pad, setting the clock

 

 

 

and resetting any cooking function.

 

 

 

 

Steam from the vent

 

When using the convection

• This is normal.

 

 

feature, it is normal to see

 

 

 

steam coming out of the oven

 

 

 

vent. As the number of racks

 

 

 

or amount of food being

 

 

 

cooked increases, the amount

 

 

 

of visible steam will increase.

 

 

 

 

 

“Burning” or “oily”

 

This is normal in a new oven

• To speed the process, set a self-clean cycle for a

odor emitting from

 

and will disappear in time.

minimum of 3 hours. See the Using the self-cleaning

the vent

 

 

oven section.

 

 

 

 

Strong odor

 

An odor from the insulation

• This is temporary.

 

 

around the inside of the oven

 

 

 

is normal for the first few times

 

 

the oven is used.

 

 

 

 

 

Fan noise

 

A convection fan may

• This is normal. To maximize cooking evenness,

 

 

automatically turn on

the fan is designed to operate in both directions,

 

 

and off.

with a pause in between.

 

 

 

 

Oven racks are

 

The shiny, silver-colored

• Apply a small amount of vegetable oil to a paper

difficult to slide

 

racks were cleaned in a

towel and wipe the edges of the oven racks with

 

 

self-clean cycle.

the paper towel. Do not spray with Pam® or other

 

 

 

lubricant sprays.

Consumer

No power supply from convenience outlet on top of backguard (on some models)

Small appliance plug is not

• Make sure the small appliance plug is properly

completely inserted in the

inserted.

convenience outlet.

 

 

 

The backguard is too hot

• Allow the range to cool, then reset the circuit

and the convenience outlet

breaker by pressing the switch located near the

breaker has tripped.

convenience outlet.

44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Model # Serial # Write the model and serial numbers hereConsumer Support Troubleshooting Tips All ranges can tip and injury could resultSafety Instructions SupportRadiant Surface Units Operating Instructions Care Troubleshooting Tips ConsumerCleaning Temperature Limiter About the radiant surface unitsInstructions Consumer SupportTroubleshooting Tips SafetyInstructions Operating Instructions Care and Cleaning Using the surface units How to SetUsing the Bridge Burner on some models Hot surface indicator light willFood Type Using the Warming Zone on some modelsInstructions Operating Using the oven controls Consumer Support Troubleshooting Tips Care and CleaningProgrammed functions must be reset Has been a power outageCare and Cleaning Troubleshooting Tips Consumer SupportPreheating and Pan Placement Aluminum FoilBefore you begin… Type of FoodHow to Set the Oven for Broiling SafetyBroiling Guide HI BroilUsing the timed baking and roasting features Safety InstructionsConsumer Support Troubleshooting Tips Care How to Set an Immediate Start and Automatic StopUsing the probe. on some models Troubleshooting Tips Consumer SupportInstructions Operating Instructions Care and Cleaning Do not store the probe in the ovenUsing the clock, kitchen timer and control lockout TroubleshootingAdjust the oven thermostat-Do it yourself Cleaning Troubleshooting Tips Consumer SupportTo Adjust the Thermostat Type of margarine will affect baking performanceUsing the convection oven. on some models Tips Care and CleaningCare and Cleaning Troubleshooting How to Set the Oven for Convection Baking or RoastingTips Consumer Support Convection RoastTouch the Convection Bake Safety Touch the Convection Roast pad Care and Cleaning Operating Instructions SafetyConvection Roasting Guide Using the proofing and warming features Cleaning Troubleshooting Tips Consumer SupportHow to Set the Oven For Proofing on some models How to Set the Oven For Warming on some modelsHow to Set the Oven for Cleaning Using the self-cleaning ovenBefore a Clean Cycle After a Clean Cycle Care and Cleaning Troubleshooting Tips Consumer SupportHow to Delay the Start of Cleaning Care and Cleaning Special features of your oven controlConsumer Support Troubleshooting Tips Instructions Care and Cleaning Tone VolumeTroubleshooting Tips Instructions OperatingUsing the Sabbath feature. on some models How to Set for Regular Baking/RoastingTroubleshooting Tips Consumer Support How to Exit the Sabbath FeatureCare and cleaning of the range Consumer Support TroubleshootingTips Care Operating InstructionsCare and Cleaning Troubleshooting Tips Cleaning the Oven DoorInstructions Operating Instructions Lift-Off Oven DoorOven Light Replacement ConsumerBroiler Pan and Grid Storage Drawer RemovalTroubleshooting Tips Consumer Oven FloorOven Racks and Convection Roasting Rack Stainless Steel Surfaces on some modelsCleaning the glass cooktop Normal Daily Use CleaningBurned-On Residue Heavy, Burned-On ResidueTroubleshooting Tips Glass surface-potential for permanent damageInstallation Instructions Prepare to Install the Range Install the Range Operation Checklist Accessories Looking For Something More?Before you call for service… Problem Possible Causes What To DoOven temperature Too hot or too coldOven will not work Food does not bakeClock and timer See the Using the clock and timer sectionSee the Using the self-cleaning oven section During a clean cycleControl signals after See the Special features of your oven control sectionPower outage Or start timeOwnership Registration Box Mississauga, Ontario L4Y 4G1 Consumer Product Ownership Registration GE Electric Range Warranty Care and CleaningSafety Instructions Operating Instructions GE Will ProvideConsumer Support GE Appliances Website Schedule Service Parts and AccessoriesContact Us Register Your Appliance

JCB905, JCB968 specifications

The GE JCB968 and JCB905 are two powerful and efficient telehandlers that have made significant impacts in the construction, agricultural, and industrial sectors. Renowned for their reliability and versatility, these machines are designed to meet the demands of various heavy-duty applications.

The JCB968 is equipped with a robust engine that provides exceptional power and torque. It boasts a lifting capacity of up to 6,000 kg, making it suitable for lifting heavy loads, including pallets, materials, and equipment. The unit features a maximum lifting height of approximately 9 meters, allowing users to reach bins and heights that are otherwise difficult. One of the standout features of the JCB968 is its four-wheel drive system, which enhances traction and stability on uneven terrains. The machine also utilizes hydrostatic transmission, enabling smooth acceleration and precise control, essential for operators working in tight spaces.

Conversely, the JCB905 is notable for its compact design, making it ideal for confined job sites where space is at a premium. With a lifting capacity of 5,000 kg and an impressive reach of around 5.5 meters, the JCB905 is perfect for handling lighter materials while still offering excellent performance. Its tight turning radius allows for exceptional maneuverability, ensuring that operators can navigate through narrow aisles and work areas with ease.

Both machines leverage advanced hydraulic systems that improve efficiency and increase productivity. The JCB968 and JCB905 come equipped with various attachment options, such as forks, buckets, and winches, allowing for a wide range of applications from material handling to construction tasks. The cab design of both models enhances operator comfort and visibility, which is critical in ensuring safety and reducing fatigue during long working hours.

In terms of technologies, both telehandlers incorporate telematics systems that provide real-time data on machine performance, location, and health diagnostics. This allows for better fleet management and ensures that maintenance is carried out proactively, minimizing downtime.

Overall, the GE JCB968 and JCB905 are exemplary models that combine power, agility, and efficiency, making them indispensable assets in any operation requiring versatile handling capabilities. Their blend of modern technology and user-centric design stands as a testament to JCB's commitment to innovation and customer satisfaction.
Top Page Image Contents