OperatingInstructions, TroubleshootingTips

Safety Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

OperatingInstructions

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

If the outlet is a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.

This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

When moving the refrigerator away from the wall, be careful not to roll over or damage the power cord.

InstallationInstructions

USE OF ADAPTER PLUGS (Adapter plugs not permitted in Canada)

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug.

TroubleshootingTips

However, if you must use an adapter, where local codes permit, a temporary connection may be made to a properly grounded 2-prong wall outlet by use of a UL-listed adapter available at most local hardware stores.

The larger slot in the adapter must be aligned with the larger slot in the wall outlet to provide proper polarity in the connection of the power cord.

When disconnecting the power cord from the adapter, always hold the adapter in place with one hand while pulling the power cord plug with the other hand. If this is not done, the adapter ground terminal is very likely to break with repeated use.

If the adapter ground terminal breaks, DO NOT USE the refrigerator until a proper ground has been established.

Attaching the adapter ground terminal to a wall outlet cover screw does not ground the appliance unless the cover screw is metal, and not insulated, and the wall outlet is grounded through the house wiring. You should have the circuit checked by a qualified electrician to make sure the outlet is properly grounded.

Consumer Support

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

162D9625P005, 49-60111 specifications

The GE 49-60111, also known as 162D9625P005, is a highly regarded component within the realm of gas turbine engines, specifically engineered for applications in industrial and aerospace sectors. This product exemplifies General Electric's commitment to advancing power generation technologies with outstanding performance, efficiency, and reliability.

One of the main features of the GE 49-60111 is its robust construction, designed to withstand high temperatures and pressures often encountered in gas turbine operations. The component plays a crucial role in enhancing the overall thermal efficiency of the engine, which is a critical factor in fuel consumption and environmental impact.

The technology behind the GE 49-60111 integrates advanced materials and manufacturing techniques. This includes the use of high-performance alloys that provide enhanced durability while minimizing weight. The component is designed to maintain structural integrity under extreme operational conditions, which is vital for sustaining the engine's longevity and ensuring safety.

Another notable characteristic of the GE 49-60111 is its aerodynamic design. The component features optimized geometries that facilitate improved airflow, contributing to higher combustion efficiency. This design not only boosts performance but also contributes to lower emissions, aligning with modern regulatory requirements and environmental standards.

In terms of maintenance, the GE 49-60111 is engineered for ease of serviceability. Its design allows for straightforward inspection and replacement, minimizing downtime and maintenance costs for operators. This focus on maintenance efficiency is particularly valuable in industrial settings where operational reliability is paramount.

The GE 49-60111 also epitomizes the integration of digital technologies in modern gas turbine systems. Advanced sensors and monitoring systems are often incorporated to provide real-time data on component performance. This data-driven approach allows operators to predict maintenance needs, optimize performance, and extend the lifecycle of the turbine.

Overall, the GE 49-60111, 162D9625P005, stands as a testament to General Electric's innovation in gas turbine technology. With its combination of durability, efficiency, aerodynamic design, and advanced maintenance features, it serves as a critical component in the pursuit of enhanced power generation capabilities while navigating the challenges of modern energy demands.