GE 200D2600P001, 21 installation instructions Consumer Support, Instructions Operating Instructions

Page 4

Safety Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

Instructions Operating Instructions

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

If the outlet is a standard 2-prong outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.

This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

When moving the refrigerator away from the wall, be careful not to roll over or damage the power cord.

USE OF ADAPTER PLUGS (Adapter plugs not permitted in Canada)

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug.

Troubleshooting Tips Installation

However, if you must use an adapter, where local codes permit, a temporary connection may be made to a properly grounded 2-prong wall outlet by use of a UL-listed adapter available at most local hardware stores.

The larger slot in the adapter must be aligned with the larger slot in the wall outlet to provide proper polarity in the connection of the power cord.

When disconnecting the power cord from the adapter, always hold the adapter in place with one hand while pulling the power cord plug with the other hand. If this is not done, the adapter ground terminal is very likely to break with repeated use.

If the adapter ground terminal breaks, DO NOT USE the refrigerator until a proper ground has been established.

Attaching the adapter ground terminal to a wall outlet cover screw does not ground the appliance unless the cover screw is metal, and not insulated, and the wall outlet is grounded through the house wiring. You should have the circuit checked by a qualified electrician to make sure the outlet is properly grounded.

Consumer Support

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

4

Image 4
Contents Write the model and serial numbers here 200D2600P001 Rev49-60104-2 01-01 JR Safety Precautions Before You Throw Away Your Old Refrigerator or Freezer Operating InstructionsCFC Disposal Consumer Support Troubleshooting Tips InstallationInstructions Operating Instructions About the temperature controls Testing and Adjusting TemperaturesTroubleshooting Tips Performance Air Flow SystemAbout the water and FreshSaver filters InstructionsSafety About the shelves and binsRefrigerator Door Bins and Freezer Door Tilt-Out Bins Large BinsConsumer Support Troubleshooting Tips Installation About the additional features Installation InstructionsTroubleshooting Tips Consumer Support About the refrigerator doorsTips Installation Instructions Operating Instructions Safety InstructionsAbout the storage drawers About storage drawer removalAbout the automatic icemaker Troubleshooting Tips Consumer SupportAutomatic Icemaker About the ice and water dispenser Care and cleaning of the refrigerator Cleaning the OutsideCleaning the Inside Ice Storage Drawer on Dispenser ModelsConsumer Support Troubleshooting Cleaning the condenserCondenser Behind the RefrigeratorReplacing the light bulbs Instructions Installation Instructions TroubleshootingInstructions Operating Preparing to install the refrigerator Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips Refrigerator LocationSafety Instructions Operating Instructions Dimensions and Specifications for CustomStyle modelsTips Consumer SupportPanels less than 1/4″ 6 mm thick Trim kits and decorator panels″ 19 mm or Raised Panel Dimensions for Custom Wood Panels Trim kitsFreezer Panel Fresh Food PanelInserting the door panels Loosen the Top Trim on the Freezer and Fresh Food DoorsInsert the Freezer Panel and Fresh Food Panel Hand tighten the two screws on the Top TrimInstructions Troubleshooting Tips Consumer Support Install the Side TrimInstructions Installation Secure the Side TrimRemoving the Handles Read these instructions completely and carefullyRemoving and replacing the doors Removing the DoorsReplacing the Doors Make sure the doors are closedInstalling the water line Power drillBefore You Begin What You Will NeedOperating Shut Off the Main Water SupplyTips Consumer Support Connect the Tubing to the Refrigerator Turn the Water On at the Shutoff ValvePlug In the Refrigerator Start the IcemakerNormal operating sounds Before you call for service… Problem Possible Causes What To DoIce cubes have Odor/tasteSmall or hollow cubes Door not closingNo water or ice cube ProductionBut Crushed ICE Was dispensed On some models Refrigerator has odorInstallation Instructions Troubleshooting Safety Instructions Operating InstructionsStaple your receipt here Consumer Support Troubleshooting Tips Installation InstructionsGE Will Replace What GE Will Not CoverOperating Specifications General Installation/Operation/Maintenance RequirementsHealth Claim Performance Certified by NSF/ANSI Special NoticesWater Treatment Device Certificate Number We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Safety Instructions Installation InstructionsConseils de dépannage La clientèle Conseils de dépannage ServiceSe débarrasser du CFC Service à la clientèle Conseils de dépannageLes commandes Service à la clientèleTest et ajustement des températures Système de circulation d’airInstallation De dépannage Service à la clientèle ConseilsLes filtres à eau et à FreshSaver De sécuritéConseils de dépannage Service à la clientèle Clayettes et bacsSécurité Mesures deClayette QuickSpace Paniers du congélateurClayettes de congélateur à retrait par coulissement Clayettes de congélateur fixesInstallation Autres caractéristiquesLes portes du réfrigérateur Panier mobile à breuvageLes tiroirs de rangement Enlèvement des bacs de rangementMachine à glaçons automatique Tiroir à glaceInstallation Dépannage Le distributeur d’eau et de glaçonsDe dépannage Service à la clientèle Entretien et nettoyage du réfrigérateurNettoyage de l’extérieur Nettoyage de l’intérieurMesures de CondensateurDerrière le réfrigérateur Départ en vacancesRemplacement des ampoules Compartiment réfrigérateur-lampe supérieureCompartiment réfrigérateur-lampe inférieure Compartiment congélateurEmplacement du réfrigérateur PréparationAlimentation en eau de la machine à glaçons DégagementsDimensions et spécifications pour les modèles «CustomStyle» Alignement des portesEnsembles de moulures et de panneaux décoratifs Avant de commencerPanneaux de moins de 1/4 po 6 mm d’épaisseur Panneau de 3/4 po 19 mm ou surélevéDépannage Service à la clientèle Dimensions pour les panneaux de bois sur mesureEnsembles de moulures Conseils deInsérez les panneaux du congélateur et du réfrigérateur Installation des panneaux de porteSerrez à la main les deux vis sur la garniture supérieure Installez la moulure latérale Fixez la moulure latéraleInstallation des poignées Installation des panneaux de porteEnlèvement des poignées Démontage et remontage des portes Sécurité FonctionnementMesures de Démontage des portesMatériel nécessaire Installation de la conduite d’eauPerceuse électrique Ouvrez le robinet et rincez le tuyau Installez le robinet d’arrêtMesures de sécurité Raccordez le tuyau de cuivre au réfrigérateur Ouvrez le robinet d’arrêt de la conduite d’eau principaleBranchez le réfrigérateur Mettez la machine à glaçons en marcheBruits de fonctionnement normaux Mesures de sécurité Fonctionnement InstallationMachine à glaçons sur certains modèles Avant d’appeler un réparateur… ProblèmeFonctionnement Installation Service à laClientèle Problème Causes possibles CorrectifsLa machine à glaçons Fonctionne, mais neDistribue pas d’eau Ne distribue ni eauGarantie DU Client Agraphez votre reçu iciSpécifications d’opération Exigences générales d’installation/opération/entretienAvis spéciaux Un service satisfaisant Numéros de servicePour les besoins particuliers Aux États-Unis Solucionar problemas Solucionar problemas Servicio Al consumidorAntes de deshacerse de su viejo refrigerador o congelador Deshacerse del CFCSolucionar problemas Servicio al consumidorSolucionar problemas Los controles del refrigeradorComprobar y ajustar la temperatura Sistema de rendimiento de circulación de aireLos filtros de agua y FreshSaver Instalación ProblemasServicio al consumidor Solucionar Solucionar problemas Servicio al consumidor Los entrepaños y recipientes del refrigeradorRecipientes grandes Recipientes pequeñosEntrepaño deslizable a prueba de derramamientos Entrepaño QuickSpaceCestas de congelador Entrepaños deslizantes del congeladorCaracterísticas adicionales Puertas del refrigeradorColgador de bebidas extraíble Puertas del refrigeradorGavetas para guardar Gavetas para guardarGavetas con humedad ajustable Gaveta convertible para carnesDispositivo automático para hacer hielo en algunos modelos El dispositivo automático para hacer hieloGaveta de almacenamiento de hielo El dispensador de agua y de hielo Problemas Servicio al consumidor Cuidado y limpieza del refrigeradorInstalación Solucionar Limpiar el exteriorServicio al consumidor SeguridadReemplazo de bombillas Compartimento del refrigerador-Luz superiorCompartimento del refrigerador-Luz inferior Compartimento del congeladorPreparación para instalar el refrigerador Ubicación del refrigeradorEspacios libres Seguridad OperaciónProblemas Servicio al Dimensiones y especificaciones para modelos de CustomStyleConsumidor Alineación de las puertasMolduras y paneles decorativos Antes de que empiecePaneles de menos de 1/4 ″ 6 mm de espesor Panel de 3/4 ″ 19 mm o panel levantadoCuidado de los paneles precortados MoldurasCon dispensador Cómo insertar los paneles de la puerta Apriete los dos tornillos de la moldura superior con la manoInstalación de la moldura lateral Asegure la moldura lateralRemoción de las manijas Inserción de los paneles de la puertaInstalación de la manijas Servicio al consumidor SolucionarCómo retirar y reemplazar las puertas Cómo retirar las puertasCómo reponer las puertas Asegúrese de que las puertas estén cerradasLo que se necesita Instalación de la línea de aguaTaladro eléctrico Corte el paso de agua del abastecimiento principal OperaciónInstale la llave de paso Haga pasar el tubo de cobre y conéctelo a la llave de pasoConecte el tubo de cobre al refrigerador Abra el agua en la llave de pasoArranque el dispositivo para hacer hielo Enchufe el cable eléctrico del refrigeradorSeguridad Operación Instalación Sonidos normales de la operaciónDispositivo para hacer hielo en algunos modelos Problema Causas Posibles Qué hacer Servicio al consumidor Solucionar problemasAntes de solicitar un servicio… Para hacer hielo no Funciona en algunosModelos El agua tiene unInstalación Servicio al consumidor Solucionar problemas Abren las puertas No funciona la luz InteriorAgua en el piso de la Cocina o en el fondoNotas Lo que GE no cubrirá Durante GE reemplazaráGarantidor General Electric Company. Louisville, KY Especificaciones de Operación Avisos EspecialesNúmeros de servicio Schedule Service Parts and AccessoriesConsumer Support GE Appliances Website Real Life Design Studio

21, 200D2600P001 specifications

The GE 200D2600P001 is a high-performance digital control system designed specifically for industrial applications. This robust system offers advanced features and technologies that enhance operational efficiency and reliability for various processes, making it a preferred choice for many industries, including oil and gas, power generation, and manufacturing.

One of the main features of the GE 200D2600P001 is its modular architecture, which allows for easy scalability and customization. Users can configure the system according to their specific needs, whether they require a simple setup for smaller applications or a complex configuration for large-scale operations. This flexibility makes it suitable for a wide range of projects and processes.

Another significant characteristic of the GE 200D2600P001 is its user-friendly interface. The system comes equipped with an intuitive graphical user interface (GUI) that simplifies monitoring and control tasks. Operators can easily navigate through different function modules, visualize process data, and access real-time reports, which enhances decision-making and optimizes workflow.

In terms of technology, the GE 200D2600P001 integrates cutting-edge communication protocols. It supports various industry-standard protocols, including Modbus, Ethernet/IP, and HART, ensuring seamless integration with other systems and devices. This interoperability facilitates data exchange and enhances the overall performance of industrial processes.

Additionally, the GE 200D2600P001 features advanced diagnostic tools that help to ensure maintenance and reduce downtime. The system is equipped with built-in self-monitoring capabilities that allow it to detect anomalies and alert operators to potential issues before they escalate into significant problems. This proactive approach to maintenance leads to increased equipment availability and longevity.

Moreover, the system is designed with security in mind, incorporating multiple layers of protection against cyber threats. This commitment to cybersecurity ensures that sensitive data remains secure and operational integrity is maintained.

Overall, the GE 200D2600P001 stands out for its modularity, user-friendly interface, advanced communication capabilities, and robust diagnostic tools. These characteristics make it an exceptional choice for industries seeking to optimize their control systems and enhance productivity while ensuring safety and security. With its reliable performance and adaptability, the GE 200D2600P001 represents a valuable investment for any industrial operation.