Whirlpool MAH9700AW Troubleshooting Procedures, 16025909 Rev, Maytag Services, Press Off twice

Page 14

Press Off twice

Troubleshooting Procedures

!WARNING

To avoid risk of electrical shock, personal injury or death, disconnect power to unit before servicing, unless testing requires power.

Test or Display

Fast

Time-

Down / Advance to Next Step

Quick

Service

Cycle

Hold Quick

Service Cycle

Step

LED/Switch

Test

Press LED to	Press LED to
Start	Cancel
Press	Press Power
Temperature	Off
to start test.
Press
Temperature
during cycle to
advance.
Press	Press Off (also
Temperature	exits Service
and Soil Level	Mode)
Press	Press
Rinse&Spin	Rinse&Spin
and Spin Only	and Spin Only
together	to resume
Press Delay for	Press Off twice
3 seconds (then	after starting
individual	test
buttons to test)
Rotate Cycle
Selector
clockwise, the
LED’s around it
will be toggled.

Test or Display

All Diagnostic Codes

Cycle Count No. for Diagnostic Code

Clear All

Diagnostic

Codes

Display

Software

Version

Cycle Count

Press LED to	Press LED to
Start	Cancel
Rotate Cycle	N/A
Selector either
direction
Press and hold	Release Rotary
Rotary	Selector
Selector, while	(returns to
diagnostic code	diagnostic code
is displayed	display)
Press Delay
and Chime
together while
displaying
diagnostic
codes
Press Soil	Press Soil
Level. Press 2	Level a 3rd time
times for
displays with
only 2 character
positions.
Press Chime

Rotate

counterclockwis

e, the7-

segment LED’s

toggle. Press

Rotary Cycle

Selector, all of

the LED’s

around the

Rotary Cycle

Quick Spin Test

While in Service Mode, press Delay and Rinse&Spin keys to start a Quick Spin Test. Quick Spin test steps are as follows:

•Start spinning and after reaching a maximum spin speed.

•stay at maximum spin speed for 2 minutes and stop Quick Spin Test.

Hold Quick Spin Step

IN

Board

Input

Test

Selector will be
toggled.
Press Spin	Press Spin
Only	Only

If the Rotary Selector key is pressed during the Quick Spin test, the machine will hold at the next highest index speed for up to 10 minutes. At the end of 10 minutes, the machine will resume and finish the Quick Spin test. To cancel the Hold and allow the

Board

Output

Test /

System Check

Diagnostic Code Display (Initial)

Press Spin	Press Off
Speed
Press Rinse&	Press
Spin – displays	Rinse&Spin
“d”	again

Spin Test to continue, press the Delay and Rinse&Spin keys.

14

16025909 Rev. 0

©2005 Maytag Services

Image 14

Contents 27” Front Load Washer MAH9700AWService This Base Manual covers general informationREVIEW ALL APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS Important Notices for Servicers and ConsumersCustomer Service Support Center Recognize Safety Symbols, Words, and LabelsDisassembly Procedures TroubleshootingComponent Testing Information General Informationwhen required. Do not do it yourself unless you know how Important Safety InformationRead all instructions before using the washer Replace worn power cords and/or loose plugsGeneral Information Electrical Service InformationAbout Ground Wires Related PublicationsTo avoid the risk of electrical shock or death, do not alter the plug Grounding InstructionsExplanation Important Safety Information Extended Service Plan ServiceParts and Accessories General InformationM A H 9 Feature Content9700 Feature Package 0 0 A Y WLeaking Troubleshooting ProceduresWill Not Start No TumbleSee Will Not Spin Perform Board Output TestWet Clothes Will Not LockAdditive Cups Full of Water Noisy and/or Vibration/WalkingRubber Feet Leaving Marks on Floor Buttons do not RespondService Mode Press Off exitsPress Spin Press Off twicecounterclockwis 16025909 Rev “Whites ”and the “Rotary Cycle Selector” is “Delicates” and the “Rotary Cycle Selector” button is pressed, the bleach valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level 16025909 Rev Go to Door Lock spinsMembrane Pad taken 1 Press Chime and Extra Rinse keys for 3seconds again, orCode Illustration Component Testing InformationTest Procedure ComponentCN10 ATC Controlwash cycle no reheating Water flow through dispenser during Wash fillNote The heater will not turn on more than once in a WASHWater flow through dispenser during Rinse 1 fill RINSEWater flow through dispenser during Rinse 2 fill RINSEWater Level Sensor Removal Disassembly ProceduresTop Removal Reactor Removal Disassembly ProceduresEMI Filter Removal Combo Cold Valve Water Valve RemovalDispenser Removal Hot ValveDoor Removal Console Removal3. Remove hinge retainer plate Disassembly Procedures2005 Maytag Services 6. Remove the glass retainerFront Panel Removal 2005 Maytag Services Boot RemovalHeater Removal Motor Removal Disassembly Procedures Drain Pump Removal Outer Tub and Spinner Removal 1x12 - 32” long17. Remove ground wire 15.Remove Pressure Switch harness connector 16. Remove the Pressure Hose 14.Remove fill hoseDisassembly Procedures Disassembly Procedures 27.Lift Spinner to access Wave Washer 28.Remove screw and release tab to remove BafflesAppendix A DC68-02032B 2005 Maytag Services WA RNING DRAIN FACILITY ALCOVE OR CLOSET INSTALLATIONLOCATION CONSIDERATIONS FLOORING2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services Appendix B 2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services Code Sy mbol INFORM ATION CODEST ROUBLESHOOTING M eani ng2005 Maytag Services 16025909 Rev