Whirlpool MAH9700AW manual Disassembly Procedures, Remove screw and release tab to remove Baffles

Page 40

28.Remove screw and release tab to remove Baffles

Disassembly Procedures

!WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to unit before servicing.

28.Remove screw and release tab to remove Baffles

27.Lift Spinner to access Wave Washer.

40	16025909 Rev. 0

©2005 Maytag Services

Image 40

Contents MAH9700AW Service27” Front Load Washer This Base Manual covers general informationImportant Notices for Servicers and Consumers Customer Service Support CenterREVIEW ALL APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS Recognize Safety Symbols, Words, and LabelsTroubleshooting Component Testing InformationDisassembly Procedures General InformationImportant Safety Information Read all instructions before using the washerwhen required. Do not do it yourself unless you know how Replace worn power cords and/or loose plugsElectrical Service Information About Ground WiresGeneral Information Related PublicationsExplanation Grounding InstructionsTo avoid the risk of electrical shock or death, do not alter the plug Important Safety Information Service Parts and AccessoriesExtended Service Plan General InformationFeature Content 9700 Feature PackageM A H 9 0 0 A Y WTroubleshooting Procedures Will Not StartLeaking No TumblePerform Board Output Test Wet ClothesSee Will Not Spin Will Not LockNoisy and/or Vibration/Walking Rubber Feet Leaving Marks on FloorAdditive Cups Full of Water Buttons do not RespondService Mode Press Off exitscounterclockwis Press Off twicePress Spin 2005 Maytag Services “Whites ”and the “Rotary Cycle Selector” is “Delicates” and the “Rotary Cycle Selector” button is pressed, the bleach valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level 2005 Maytag Services Membrane Pad spinsGo to Door Lock Code 1 Press Chime and Extra Rinse keys for 3seconds again, ortaken Component Testing Information Test ProcedureIllustration ComponentCN10 ATC ControlWater flow through dispenser during Wash fill Note The heater will not turn on more than once in awash cycle no reheating WASHWater flow through dispenser during Rinse 1 fill RINSEWater flow through dispenser during Rinse 2 fill RINSETop Removal Disassembly ProceduresWater Level Sensor Removal EMI Filter Removal Disassembly ProceduresReactor Removal Water Valve Removal Dispenser RemovalCombo Cold Valve Hot ValveDoor Removal Console RemovalDisassembly Procedures 2005 Maytag Services3. Remove hinge retainer plate 6. Remove the glass retainerFront Panel Removal Heater Removal Boot Removal2005 Maytag Services Motor Removal Disassembly Procedures Drain Pump Removal Outer Tub and Spinner Removal 1x12 - 32” long17. Remove ground wire 15.Remove Pressure Switch harness connector 16. Remove the Pressure Hose 14.Remove fill hoseDisassembly Procedures Disassembly Procedures 27.Lift Spinner to access Wave Washer 28.Remove screw and release tab to remove BafflesAppendix A DC68-02032B 2005 Maytag Services WA RNING ALCOVE OR CLOSET INSTALLATION LOCATION CONSIDERATIONSDRAIN FACILITY FLOORING2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services Appendix B 2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services INFORM ATION CODES T ROUBLESHOOTINGCode Sy mbol M eani ng2005 Maytag Services 16025909 Rev