Whirlpool MAH9700AW manual Troubleshooting Procedures, Maytag Services, 16025909 Rev

Page 17
“Delicates” and the “Rotary Cycle Selector” button is pressed, the bleach valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level.

Troubleshooting Procedures

!WARNING

To avoid risk of electrical shock, personal injury or death, disconnect power to unit before servicing, unless testing requires power.

•Selector” button is pressed, the Main relay will be toggled (either from “on” to “off” or from“ off” to “on”).

•When the “Rotary Cycle Selector” is set to “Normal” and the “Rotary Cycle Selector” button is pressed, the hot water valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level.

•When the “Rotary Cycle Selector” is set to “Wrinkle Control” and the “Rotary Cycle Selector” button is pressed, the cold water valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level.

•When the “Rotary Cycle Selector” is set to

“Delicates” and the “Rotary Cycle Selector” button is pressed, the bleach valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level.

•When the “Rotary Cycle Selector” is set to “Hand Wash” and the “Rotary Cycle Selector” button is pressed, the pre wash valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level.

•When the “Rotary Cycle Selector” is set to “Quick Wash” and the “Rotary Cycle Selector” button is pressed, the drain pump will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output.

•Pressing the “Delay” switch pad will turn on the motor and the “Delay” LED. This output and the LED will remain on until the “Delay” switch pad is pressed again to turn off the output. When activated, the machine will tumble for 5 seconds in the CW direction, pause for 2seconds, tumble in the CCW direction for 5 seconds, pause for 2 seconds; repeating this pattern until “ Delay” button is pressed again to turn off the tumbling. Note that all tumble speeds are assumed to be 45 rpm.

•Pressing the “Chime” switch pad will unlock the door and turn on the all the LED’s above

the “Chime” button. This output will attempt to unlock one time, if safe to do so.

•Pressing the “Temperature” switch pad will lock the door and all the Temperature LED’s will turn ON. Pressing the “Chime” button will unlock the door and the all the Chime LED’s will turn ON.

•When the “Rotary Cycle Selector” is set to

“Colors” and the “Rotary Cycle Selector” is pressed, the bleach valve and the cold water valve will be turned on to check the fabric softener fill. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level.

•When the “Rinse & Spin” keypad is pressed, the Heater will be turned on if the water level is above the Heater Safety Level. If the water level is below the Heater Safety Level, a warning beep will be given and the heater will not be turned on. The Heater output will remain on until the “Rinse & Spin” keypad is pressed again to turn off the output.

Selection

Component

Function

Rotary cycle selector

 

 

set to Super Wash.

Main Relay

On to Off or

Press Rotary

Off to On

 

Selector Knob.

 

 

Rotary cycle selector

 

1st press valve

set to Normal. Press

Hot Water

on. 2nd press

Rotary Selector

Valve

valve off.

Knob.

 

 

Rotary cycle selector

 

1st press valve

set to Wrinkle

Cold Water

on. 2nd press

Control. Press

valve off.

Valve

Rotary Selector

 

 

 

Knob.

 

 

Rotary cycle selector

 

1st press valve

set to Delicates.

Bleach Valve

on. 2nd press

Press Rotary

valve off.

 

Selector Knob.

 

 

Rotary cycle selector

 

1st press valve

set to Hand Wash.

Pre Wash

on. 2nd press

Press Rotary

Valve

valve off.

Selector Knob.

 

 

©2005 Maytag Services

16025909 Rev. 0

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Service MAH9700AW27” Front Load Washer This Base Manual covers general informationCustomer Service Support Center Important Notices for Servicers and ConsumersREVIEW ALL APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS Recognize Safety Symbols, Words, and LabelsComponent Testing Information TroubleshootingDisassembly Procedures General InformationRead all instructions before using the washer Important Safety Informationwhen required. Do not do it yourself unless you know how Replace worn power cords and/or loose plugsAbout Ground Wires Electrical Service InformationGeneral Information Related PublicationsTo avoid the risk of electrical shock or death, do not alter the plug Grounding InstructionsExplanation 16025909 Rev Parts and Accessories ServiceExtended Service Plan General Information9700 Feature Package Feature ContentM A H 9 0 0 A Y WWill Not Start Troubleshooting ProceduresLeaking No TumbleWet Clothes Perform Board Output TestSee Will Not Spin Will Not LockRubber Feet Leaving Marks on Floor Noisy and/or Vibration/WalkingAdditive Cups Full of Water Buttons do not RespondPress Off exits Service ModePress Spin Press Off twicecounterclockwis 16025909 Rev “Whites ”and the “Rotary Cycle Selector” is “Delicates” and the “Rotary Cycle Selector” button is pressed, the bleach valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level 16025909 Rev Go to Door Lock spinsMembrane Pad taken 1 Press Chime and Extra Rinse keys for 3seconds again, orCode Test Procedure Component Testing InformationIllustration ComponentATC Control CN10Note The heater will not turn on more than once in a Water flow through dispenser during Wash fillwash cycle no reheating WASHRINSE Water flow through dispenser during Rinse 1 fillRINSE Water flow through dispenser during Rinse 2 fillWater Level Sensor Removal Disassembly ProceduresTop Removal Reactor Removal Disassembly ProceduresEMI Filter Removal Dispenser Removal Water Valve RemovalCombo Cold Valve Hot ValveConsole Removal Door Removal2005 Maytag Services Disassembly Procedures3. Remove hinge retainer plate 6. Remove the glass retainerFront Panel Removal 2005 Maytag Services Boot RemovalHeater Removal Motor Removal Disassembly Procedures Drain Pump Removal 1x12 - 32” long Outer Tub and Spinner Removal16. Remove the Pressure Hose 14.Remove fill hose 17. Remove ground wire 15.Remove Pressure Switch harness connectorDisassembly Procedures Disassembly Procedures 28.Remove screw and release tab to remove Baffles 27.Lift Spinner to access Wave WasherAppendix A DC68-02032B 16025909 Rev WA RNING LOCATION CONSIDERATIONS ALCOVE OR CLOSET INSTALLATIONDRAIN FACILITY FLOORING16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev Appendix B 16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev T ROUBLESHOOTING INFORM ATION CODESCode Sy mbol M eani ng16025909 Rev 2005 Maytag Services
Top Page Image Contents