Whirlpool MAH9700AW manual Disassembly Procedures, Top Removal, Water Level Sensor Removal

Page 26

Disassembly Procedures

Disassembly Procedures

!WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to unit before servicing.

Top Removal

1.Disconnect power supply to unit.

2.Remove 2 10mm screws from washer back.

3.Slide Top Cover towards the rear to clear the screw head from flange on the bottom side of the Top Cover.

Water Level Sensor Removal

1.Disconnect power supply to unit.

2.Remove Top Cover.

3.Remove harness plug.

4.Remove Pressure Hose.

5.Remove single attachment screw.

26	16025909 Rev. 0

©2005 Maytag Services

Image 26

Contents 27” Front Load Washer MAH9700AWService This Base Manual covers general informationREVIEW ALL APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS Important Notices for Servicers and ConsumersCustomer Service Support Center Recognize Safety Symbols, Words, and LabelsDisassembly Procedures TroubleshootingComponent Testing Information General Informationwhen required. Do not do it yourself unless you know how Important Safety InformationRead all instructions before using the washer Replace worn power cords and/or loose plugsGeneral Information Electrical Service InformationAbout Ground Wires Related PublicationsTo avoid the risk of electrical shock or death, do not alter the plug Grounding InstructionsExplanation Important Safety Information Extended Service Plan ServiceParts and Accessories General InformationM A H 9 Feature Content9700 Feature Package 0 0 A Y WLeaking Troubleshooting ProceduresWill Not Start No TumbleSee Will Not Spin Perform Board Output TestWet Clothes Will Not LockAdditive Cups Full of Water Noisy and/or Vibration/WalkingRubber Feet Leaving Marks on Floor Buttons do not RespondService Mode Press Off exitsPress Spin Press Off twicecounterclockwis 16025909 Rev “Whites ”and the “Rotary Cycle Selector” is “Delicates” and the “Rotary Cycle Selector” button is pressed, the bleach valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level 16025909 Rev Go to Door Lock spinsMembrane Pad taken 1 Press Chime and Extra Rinse keys for 3seconds again, orCode Illustration Component Testing InformationTest Procedure ComponentCN10 ATC Controlwash cycle no reheating Water flow through dispenser during Wash fillNote The heater will not turn on more than once in a WASHWater flow through dispenser during Rinse 1 fill RINSEWater flow through dispenser during Rinse 2 fill RINSEWater Level Sensor Removal Disassembly ProceduresTop Removal Reactor Removal Disassembly ProceduresEMI Filter Removal Combo Cold Valve Water Valve RemovalDispenser Removal Hot ValveDoor Removal Console Removal3. Remove hinge retainer plate Disassembly Procedures2005 Maytag Services 6. Remove the glass retainerFront Panel Removal 2005 Maytag Services Boot RemovalHeater Removal Motor Removal Disassembly Procedures Drain Pump Removal Outer Tub and Spinner Removal 1x12 - 32” long17. Remove ground wire 15.Remove Pressure Switch harness connector 16. Remove the Pressure Hose 14.Remove fill hoseDisassembly Procedures Disassembly Procedures 27.Lift Spinner to access Wave Washer 28.Remove screw and release tab to remove BafflesAppendix A DC68-02032B 2005 Maytag Services WA RNING DRAIN FACILITY ALCOVE OR CLOSET INSTALLATIONLOCATION CONSIDERATIONS FLOORING2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services Appendix B 2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services Code Sy mbol INFORM ATION CODEST ROUBLESHOOTING M eani ng2005 Maytag Services 16025909 Rev