Whirlpool MAH9700AW manual Grounding Instructions, Important Safety Information, Explanation

Page 6
Explanation

Important Safety Information

Explanation

Polarization–This means that the larger slot must be neutral and the small slot must be at line voltage. Mispolarized–The outlet is incorrectly wired so that the larger slot is at line voltage and the smaller slot is neutral. Grounded–This means the round hole connection is con- nected to earth ground through a connection to the main power panel.

Ungrounded–The round hole connection is not complete to earth ground and/or the main power panel.

Grounding Instructions

To avoid the risk of electrical shock or death, do not alter the plug.

Do not remove grounding prong when installing grounded appliance in a home that does not have three wire grounding receptacle. Under no condition is grounding prong to be cut off or removed. It is the personal responsibility of the consumer to contact a qualified electrician and have properly grounded three prong wall receptacle installed in accordance with appropriate electrical codes.

To avoid the risk of electrical shock or death, this equipment must be grounded.

This equipment MUST be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This unit is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

Consult a qualified electrician or technician if grounding instructions are not completely understood, or if doubt exists as to whether the equipment is properly grounded. Do not use an extension cord. If the product power cord is too short, have a qualified electrician install a three-slot receptacle. This unit should be plugged into a separate 60 hertz circuit with the electrical rating as shown in the appropriate drawing. Models operate with a supply voltage of 120 Volts.

6

16025909 Rev. 0

©2005Maytag Services

Image 6
Contents 27” Front Load Washer MAH9700AWService This Base Manual covers general informationREVIEW ALL APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS Important Notices for Servicers and ConsumersCustomer Service Support Center Recognize Safety Symbols, Words, and LabelsDisassembly Procedures TroubleshootingComponent Testing Information General Informationwhen required. Do not do it yourself unless you know how Important Safety InformationRead all instructions before using the washer Replace worn power cords and/or loose plugsGeneral Information Electrical Service InformationAbout Ground Wires Related PublicationsGrounding Instructions ExplanationTo avoid the risk of electrical shock or death, do not alter the plug Important Safety Information Extended Service Plan ServiceParts and Accessories General InformationM A H 9 Feature Content9700 Feature Package 0 0 A Y WLeaking Troubleshooting ProceduresWill Not Start No TumbleSee Will Not Spin Perform Board Output TestWet Clothes Will Not LockAdditive Cups Full of Water Noisy and/or Vibration/WalkingRubber Feet Leaving Marks on Floor Buttons do not RespondService Mode Press Off exitsPress Off twice counterclockwisPress Spin Troubleshooting Procedures “Whites ”and the “Rotary Cycle Selector” is “Delicates” and the “Rotary Cycle Selector” button is pressed, the bleach valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level Troubleshooting Procedures spins Membrane PadGo to Door Lock 1 Press Chime and Extra Rinse keys for 3seconds again, or Codetaken Illustration Component Testing InformationTest Procedure ComponentCN10 ATC Controlwash cycle no reheating Water flow through dispenser during Wash fillNote The heater will not turn on more than once in a WASHWater flow through dispenser during Rinse 1 fill RINSEWater flow through dispenser during Rinse 2 fill RINSEDisassembly Procedures Top RemovalWater Level Sensor Removal Disassembly Procedures EMI Filter RemovalReactor Removal Combo Cold Valve Water Valve RemovalDispenser Removal Hot ValveDoor Removal Console Removal3. Remove hinge retainer plate Disassembly Procedures2005 Maytag Services 6. Remove the glass retainerFront Panel Removal Boot Removal Heater Removal2005 Maytag Services Motor Removal Disassembly Procedures Drain Pump Removal Outer Tub and Spinner Removal 1x12 - 32” long17. Remove ground wire 15.Remove Pressure Switch harness connector 16. Remove the Pressure Hose 14.Remove fill hoseDisassembly Procedures Disassembly Procedures 27.Lift Spinner to access Wave Washer 28.Remove screw and release tab to remove BafflesAppendix A DC68-02032B 2005 Maytag Services WA RNING DRAIN FACILITY ALCOVE OR CLOSET INSTALLATIONLOCATION CONSIDERATIONS FLOORING2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services Appendix B 2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services Code Sy mbol INFORM ATION CODEST ROUBLESHOOTING M eani ng2005 Maytag Services 16025909 Rev