Whirlpool MAH9700AW manual Outer Tub and Spinner Removal, 1x12 - 32” long, Disassembly Procedures

Page 36

Outer Tub and Spinner Removal

Disassembly Procedures

!WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to unit before servicing.

Outer Tub and Spinner Removal

1.Disconnect power supply to unit.

2.Remove Top Cover.

3.Remove Console.

4.Remove Front Panel.

5. Remove Back Cover.

6.Remove Pump Hose.

7.Remove the Drain Hose

8.Remove the two 13mm bolts securing the Rear Struts to the base.

NOTE: Torque bolts to 11-22 ft lbs. during installtion.

11. Remove wire harness connectors for the heater, Themistor and ground.

12.Remove two 13mm bolts securing the Front Struts to base and rotate up against the bottom of the tub.

13.Insert a board or boards across the bottom of the washer frame to use as a support when removing the tub assembly.

9.Rotate the struts up against the bottom of the tub to ease removal of the tub assembly.

1x12 - 32” long

NOTE: The rear struts can be identified by the green sleeve.

10.Remove two each side 13mm bolts securing Counter Weights.

36	16025909 Rev. 0

©2005 Maytag Services

Image 36

Contents MAH9700AW Service27” Front Load Washer This Base Manual covers general informationImportant Notices for Servicers and Consumers Customer Service Support CenterREVIEW ALL APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS Recognize Safety Symbols, Words, and LabelsTroubleshooting Component Testing InformationDisassembly Procedures General InformationImportant Safety Information Read all instructions before using the washerwhen required. Do not do it yourself unless you know how Replace worn power cords and/or loose plugsElectrical Service Information About Ground WiresGeneral Information Related PublicationsGrounding Instructions ExplanationTo avoid the risk of electrical shock or death, do not alter the plug Important Safety Information Service Parts and AccessoriesExtended Service Plan General InformationFeature Content 9700 Feature PackageM A H 9 0 0 A Y WTroubleshooting Procedures Will Not StartLeaking No TumblePerform Board Output Test Wet ClothesSee Will Not Spin Will Not LockNoisy and/or Vibration/Walking Rubber Feet Leaving Marks on FloorAdditive Cups Full of Water Buttons do not RespondService Mode Press Off exitsPress Off twice counterclockwisPress Spin Troubleshooting Procedures “Whites ”and the “Rotary Cycle Selector” is “Delicates” and the “Rotary Cycle Selector” button is pressed, the bleach valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level Troubleshooting Procedures spins Membrane PadGo to Door Lock 1 Press Chime and Extra Rinse keys for 3seconds again, or Codetaken Component Testing Information Test ProcedureIllustration ComponentCN10 ATC ControlWater flow through dispenser during Wash fill Note The heater will not turn on more than once in awash cycle no reheating WASHWater flow through dispenser during Rinse 1 fill RINSEWater flow through dispenser during Rinse 2 fill RINSEDisassembly Procedures Top RemovalWater Level Sensor Removal Disassembly Procedures EMI Filter RemovalReactor Removal Water Valve Removal Dispenser RemovalCombo Cold Valve Hot ValveDoor Removal Console RemovalDisassembly Procedures 2005 Maytag Services3. Remove hinge retainer plate 6. Remove the glass retainerFront Panel Removal Boot Removal Heater Removal2005 Maytag Services Motor Removal Disassembly Procedures Drain Pump Removal Outer Tub and Spinner Removal 1x12 - 32” long17. Remove ground wire 15.Remove Pressure Switch harness connector 16. Remove the Pressure Hose 14.Remove fill hoseDisassembly Procedures Disassembly Procedures 27.Lift Spinner to access Wave Washer 28.Remove screw and release tab to remove BafflesAppendix A DC68-02032B 2005 Maytag Services WA RNING ALCOVE OR CLOSET INSTALLATION LOCATION CONSIDERATIONSDRAIN FACILITY FLOORING2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services Appendix B 2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services INFORM ATION CODES T ROUBLESHOOTINGCode Sy mbol M eani ng2005 Maytag Services 16025909 Rev