Whirlpool MAH9700AW manual Disassembly Procedures, Remove the Pressure Hose 14.Remove fill hose

Page 37

16. Remove the Pressure Hose.

Disassembly Procedures

!WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to unit before servicing.

16. Remove the Pressure Hose.

14.Remove fill hose.

17. Remove ground wire.

15.Remove Pressure Switch harness connector.

©2005 Maytag Services

16025909 Rev. 0

37

Image 37

Contents Service MAH9700AW27” Front Load Washer This Base Manual covers general informationCustomer Service Support Center Important Notices for Servicers and ConsumersREVIEW ALL APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS Recognize Safety Symbols, Words, and LabelsComponent Testing Information TroubleshootingDisassembly Procedures General InformationRead all instructions before using the washer Important Safety Informationwhen required. Do not do it yourself unless you know how Replace worn power cords and/or loose plugsAbout Ground Wires Electrical Service InformationGeneral Information Related PublicationsExplanation Grounding InstructionsTo avoid the risk of electrical shock or death, do not alter the plug 16025909 Rev Parts and Accessories ServiceExtended Service Plan General Information9700 Feature Package Feature ContentM A H 9 0 0 A Y WWill Not Start Troubleshooting ProceduresLeaking No TumbleWet Clothes Perform Board Output TestSee Will Not Spin Will Not LockRubber Feet Leaving Marks on Floor Noisy and/or Vibration/WalkingAdditive Cups Full of Water Buttons do not RespondPress Off exits Service Modecounterclockwis Press Off twicePress Spin 2005 Maytag Services “Whites ”and the “Rotary Cycle Selector” is “Delicates” and the “Rotary Cycle Selector” button is pressed, the bleach valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level 2005 Maytag Services Membrane Pad spinsGo to Door Lock Code 1 Press Chime and Extra Rinse keys for 3seconds again, ortaken Test Procedure Component Testing InformationIllustration ComponentATC Control CN10Note The heater will not turn on more than once in a Water flow through dispenser during Wash fillwash cycle no reheating WASHRINSE Water flow through dispenser during Rinse 1 fillRINSE Water flow through dispenser during Rinse 2 fillTop Removal Disassembly ProceduresWater Level Sensor Removal EMI Filter Removal Disassembly ProceduresReactor Removal Dispenser Removal Water Valve RemovalCombo Cold Valve Hot ValveConsole Removal Door Removal2005 Maytag Services Disassembly Procedures3. Remove hinge retainer plate 6. Remove the glass retainerFront Panel Removal Heater Removal Boot Removal2005 Maytag Services Motor Removal Disassembly Procedures Drain Pump Removal 1x12 - 32” long Outer Tub and Spinner Removal16. Remove the Pressure Hose 14.Remove fill hose 17. Remove ground wire 15.Remove Pressure Switch harness connectorDisassembly Procedures Disassembly Procedures 28.Remove screw and release tab to remove Baffles 27.Lift Spinner to access Wave WasherAppendix A DC68-02032B 16025909 Rev WA RNING LOCATION CONSIDERATIONS ALCOVE OR CLOSET INSTALLATIONDRAIN FACILITY FLOORING16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev Appendix B 16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev T ROUBLESHOOTING INFORM ATION CODESCode Sy mbol M eani ng16025909 Rev 2005 Maytag Services