Whirlpool MAH9700AW manual Disassembly Procedures, EMI Filter Removal, Reactor Removal

Page 27

Disassembly Procedures

Disassembly Procedures

!WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to unit before servicing.

NOTE: The reactor coil is wired in series with line 1 internally in the Control Board. An open coil or loose electrical connection would result in a “dead” board complaint. A resistance check across the coil leads should indicate less than 1 ohm.

EMI Filter Removal

1. Disconnect power supply to unit.

2. Remove Top Cover.

3. Loosen 13mm acorn nut and slide EMI Filter out of bracket.

Reactor Removal

1.Disconnect power supply to unit.

2.Remove Top Cover.

3.Remove single attachment screw on cross brace.

4.Twist Reactor counterclockwise to remove.

NOTE: Mark the wire locations on the EMI before removing the terminals.

©2005 Maytag Services

16025909 Rev. 0

27

Image 27

Contents This Base Manual covers general information MAH9700AWService 27” Front Load WasherRecognize Safety Symbols, Words, and Labels Important Notices for Servicers and ConsumersCustomer Service Support Center REVIEW ALL APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRSGeneral Information TroubleshootingComponent Testing Information Disassembly ProceduresReplace worn power cords and/or loose plugs Important Safety InformationRead all instructions before using the washer when required. Do not do it yourself unless you know howRelated Publications Electrical Service InformationAbout Ground Wires General InformationGrounding Instructions ExplanationTo avoid the risk of electrical shock or death, do not alter the plug 16025909 Rev General Information ServiceParts and Accessories Extended Service Plan0 0 A Y W Feature Content9700 Feature Package M A H 9No Tumble Troubleshooting ProceduresWill Not Start LeakingWill Not Lock Perform Board Output TestWet Clothes See Will Not SpinButtons do not Respond Noisy and/or Vibration/WalkingRubber Feet Leaving Marks on Floor Additive Cups Full of WaterPress Off exits Service ModePress Off twice counterclockwisPress Spin Troubleshooting Procedures “Whites ”and the “Rotary Cycle Selector” is “Delicates” and the “Rotary Cycle Selector” button is pressed, the bleach valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level Troubleshooting Procedures spins Membrane PadGo to Door Lock 1 Press Chime and Extra Rinse keys for 3seconds again, or Codetaken Component Component Testing InformationTest Procedure IllustrationATC Control CN10WASH Water flow through dispenser during Wash fillNote The heater will not turn on more than once in a wash cycle no reheatingRINSE Water flow through dispenser during Rinse 1 fillRINSE Water flow through dispenser during Rinse 2 fillDisassembly Procedures Top RemovalWater Level Sensor Removal Disassembly Procedures EMI Filter RemovalReactor Removal Hot Valve Water Valve RemovalDispenser Removal Combo Cold ValveConsole Removal Door Removal6. Remove the glass retainer Disassembly Procedures2005 Maytag Services 3. Remove hinge retainer plateFront Panel Removal Boot Removal Heater Removal2005 Maytag Services Motor Removal Disassembly Procedures Drain Pump Removal 1x12 - 32” long Outer Tub and Spinner Removal16. Remove the Pressure Hose 14.Remove fill hose 17. Remove ground wire 15.Remove Pressure Switch harness connectorDisassembly Procedures Disassembly Procedures 28.Remove screw and release tab to remove Baffles 27.Lift Spinner to access Wave WasherAppendix A DC68-02032B 16025909 Rev WA RNING FLOORING ALCOVE OR CLOSET INSTALLATIONLOCATION CONSIDERATIONS DRAIN FACILITY16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev Appendix B 16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev M eani ng INFORM ATION CODEST ROUBLESHOOTING Code Sy mbol16025909 Rev 2005 Maytag Services