Whirlpool MAH9700AW manual Disassembly Procedures, Remove hinge retainer plate, 16025909 Rev

Page 30

Disassembly Procedures

Disassembly Procedures

!WARNING

To avoid risk of electrical shock, personal injury or death; disconnect power to unit before servicing.

3. Remove hinge retainer plate.

6. Remove the glass retainer.

7. Remove glass.

4. Remove door from hinge posts.

8. Remove external viewing window.

5.Remove Screws around the perimeter of the glass retainer.

26	16025909 Rev. 0

©2005 Maytag Services

Image 30

Contents 27” Front Load Washer MAH9700AWService This Base Manual covers general informationREVIEW ALL APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS Important Notices for Servicers and ConsumersCustomer Service Support Center Recognize Safety Symbols, Words, and LabelsDisassembly Procedures TroubleshootingComponent Testing Information General Informationwhen required. Do not do it yourself unless you know how Important Safety InformationRead all instructions before using the washer Replace worn power cords and/or loose plugsGeneral Information Electrical Service InformationAbout Ground Wires Related PublicationsGrounding Instructions ExplanationTo avoid the risk of electrical shock or death, do not alter the plug Important Safety Information Extended Service Plan ServiceParts and Accessories General InformationM A H 9 Feature Content9700 Feature Package 0 0 A Y WLeaking Troubleshooting ProceduresWill Not Start No TumbleSee Will Not Spin Perform Board Output TestWet Clothes Will Not LockAdditive Cups Full of Water Noisy and/or Vibration/WalkingRubber Feet Leaving Marks on Floor Buttons do not RespondService Mode Press Off exitsPress Off twice counterclockwisPress Spin Troubleshooting Procedures “Whites ”and the “Rotary Cycle Selector” is “Delicates” and the “Rotary Cycle Selector” button is pressed, the bleach valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level Troubleshooting Procedures spins Membrane PadGo to Door Lock 1 Press Chime and Extra Rinse keys for 3seconds again, or Codetaken Illustration Component Testing InformationTest Procedure ComponentCN10 ATC Controlwash cycle no reheating Water flow through dispenser during Wash fillNote The heater will not turn on more than once in a WASHWater flow through dispenser during Rinse 1 fill RINSEWater flow through dispenser during Rinse 2 fill RINSEDisassembly Procedures Top RemovalWater Level Sensor Removal Disassembly Procedures EMI Filter RemovalReactor Removal Combo Cold Valve Water Valve RemovalDispenser Removal Hot ValveDoor Removal Console Removal3. Remove hinge retainer plate Disassembly Procedures2005 Maytag Services 6. Remove the glass retainerFront Panel Removal Boot Removal Heater Removal2005 Maytag Services Motor Removal Disassembly Procedures Drain Pump Removal Outer Tub and Spinner Removal 1x12 - 32” long17. Remove ground wire 15.Remove Pressure Switch harness connector 16. Remove the Pressure Hose 14.Remove fill hoseDisassembly Procedures Disassembly Procedures 27.Lift Spinner to access Wave Washer 28.Remove screw and release tab to remove BafflesAppendix A DC68-02032B 2005 Maytag Services WA RNING DRAIN FACILITY ALCOVE OR CLOSET INSTALLATIONLOCATION CONSIDERATIONS FLOORING2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services Appendix B 2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services 16025909 Rev2005 Maytag Services Code Sy mbol INFORM ATION CODEST ROUBLESHOOTING M eani ng2005 Maytag Services 16025909 Rev