Whirlpool MAH9700AW manual Troubleshooting Procedures, Maytag Services, 16025909 Rev, Membrane Pad

Page 19

"Membrane Pad

Troubleshooting Procedures

!WARNING

To avoid risk of electrical shock, personal injury or death, disconnect power to unit before servicing, unless testing requires power.

	Diag.	Description	Trigger	Action to be
	Code			taken
			Input signal
			from water
			level Sensor	Displays "LE"
		Water level	is out of	Displays "LE"
	8	Water level	range,	Go to “No water fill
	8	sensor fault.	range,	Go to “No water fill
		sensor fault.	Washer will	Troubleshooting”.
			Washer will	Troubleshooting”.
			beep and
			pause the
			wash cycle.
	9		Not Used

		Unbalance
		detected	Never	LED – Will display
		during final	Never
		during final	exceeded
		spin, which	exceeded	“dc”
	10	spin, which	400rpm due	“dc”
	10	prevented	to an	Go to "Wet Clothes
		the spinner	to an	"Troubleshooting
		the spinner	unbalance	"Troubleshooting
		from	unbalance	Section"
		from	load.	Section"
		exceeding	load.
		exceeding
		400 rpm
			Water level in
			the machine
			is believed to
			be above the
			overflow level.
			When this
			condition is	First check to see
		Water	detected, the	that water valve is
	E	sensor level	machine will	not stuck. If water
		fault.	automatically	valve is OK, check
			begin	water level sensor
			pumping
			water out of
			the machine
			until it falls
			below the
			overflow level.
				Go to "Clear
				diagnostic codes"
				Disconnect and
		Will not	Difficulty in	reconnect the
		Will not		washer power cord
		remember		washer power cord
	11	remember	reading	at power supply
	11	machine	reading	at power supply
		machine	memory	outlet.
		settings	memory	outlet.
		settings		If condition still
				If condition still
				exists, replace
				machine control
				board.

	Diag.	Description	Trigger	Action to be
	Code			taken
			A key is	Display "E2". Go to
			sensed to be	"Membrane Pad
			pressed more	Check" Check
	15	Stuck Key	than 30	connection of
	15	Stuck Key	seconds, the	keypad to control
			seconds, the	keypad to control
			key will be	board. Replace
			assumed to	LED Board if
			be stuck	necessary.
			The door has
			not been
		Door switch	opened after
		was not	two complete	Will display "od" If
	17	seen open	wash cycles.	door open sensing,
		since the last	Door switch	will cleared.
		three final	was not seen	will cleared.
		three final	was not seen
		spins	open since
			the last two
			final spins
				Check for loose
				wire connections
				Clear the diagnostic
		Detected		code and recheck;
		door lock	Open door	if reoccurs, perform
	18	switch open	lock switch	Diagnostic
	18	during cycle	with motor	Motor/Machine
		during cycle	with motor	Motor/Machine
		when not	running.	Control Board test
		expected.		Check for faulty
				motor relay on the
				machine control
				board.
	19-21		Not Used

		Door switch	Door switch is	Go to "Door Lock
		Door switch	detected open	Go to "Door Lock
		detected	and the door	Test"
	22	open during	and the door	Test"
		cycle (when	locked switch	Troubleshooting
		not paused).	is read as	Section
		not paused).	locked.
			locked.
	23-24		Not Used

12-14

Not Used

©2005 Maytag Services

16025909 Rev. 0

19

Image 19

Contents This Base Manual covers general information MAH9700AWService 27” Front Load WasherRecognize Safety Symbols, Words, and Labels Important Notices for Servicers and ConsumersCustomer Service Support Center REVIEW ALL APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRSGeneral Information TroubleshootingComponent Testing Information Disassembly ProceduresReplace worn power cords and/or loose plugs Important Safety InformationRead all instructions before using the washer when required. Do not do it yourself unless you know howRelated Publications Electrical Service InformationAbout Ground Wires General InformationExplanation Grounding InstructionsTo avoid the risk of electrical shock or death, do not alter the plug 16025909 Rev General Information ServiceParts and Accessories Extended Service Plan0 0 A Y W Feature Content9700 Feature Package M A H 9No Tumble Troubleshooting ProceduresWill Not Start LeakingWill Not Lock Perform Board Output TestWet Clothes See Will Not SpinButtons do not Respond Noisy and/or Vibration/WalkingRubber Feet Leaving Marks on Floor Additive Cups Full of WaterPress Off exits Service Modecounterclockwis Press Off twicePress Spin 2005 Maytag Services “Whites ”and the “Rotary Cycle Selector” is “Delicates” and the “Rotary Cycle Selector” button is pressed, the bleach valve will be turned on. This output will remain on until the “Rotary Cycle Selector” button is pressed again to turn off the output. The control will not allow the machine to fill past the High water level 2005 Maytag Services Membrane Pad spinsGo to Door Lock Code 1 Press Chime and Extra Rinse keys for 3seconds again, ortaken Component Component Testing InformationTest Procedure IllustrationATC Control CN10WASH Water flow through dispenser during Wash fillNote The heater will not turn on more than once in a wash cycle no reheatingRINSE Water flow through dispenser during Rinse 1 fillRINSE Water flow through dispenser during Rinse 2 fillTop Removal Disassembly ProceduresWater Level Sensor Removal EMI Filter Removal Disassembly ProceduresReactor Removal Hot Valve Water Valve RemovalDispenser Removal Combo Cold ValveConsole Removal Door Removal6. Remove the glass retainer Disassembly Procedures2005 Maytag Services 3. Remove hinge retainer plateFront Panel Removal Heater Removal Boot Removal2005 Maytag Services Motor Removal Disassembly Procedures Drain Pump Removal 1x12 - 32” long Outer Tub and Spinner Removal16. Remove the Pressure Hose 14.Remove fill hose 17. Remove ground wire 15.Remove Pressure Switch harness connectorDisassembly Procedures Disassembly Procedures 28.Remove screw and release tab to remove Baffles 27.Lift Spinner to access Wave WasherAppendix A DC68-02032B 16025909 Rev WA RNING FLOORING ALCOVE OR CLOSET INSTALLATIONLOCATION CONSIDERATIONS DRAIN FACILITY16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev Appendix B 16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev 2005 Maytag Services16025909 Rev M eani ng INFORM ATION CODEST ROUBLESHOOTING Code Sy mbol16025909 Rev 2005 Maytag Services