Zanussi ZKT6050 user manual Installation instructions, Connecting to the electricity supply

Page 35

Installation instructions

WARNING!

This appliance must be earthed

If your appliance has been damaged in transit, contact your supplier immediately. Do not attempt to install it.

Your appliance left the factory fully packaged to protect it from damage. If it is delivered without packaging and damage has occurred, the manufacturer cannot accept responsibility. Contact your supplier for advice.

Once the packaging has been removed the appliance should only be moved by hand. Do not use a sack barrow or any other aid to lift the appliance as damage may occur.

To move the appliance, open the oven door and lift the appliance by holding inside the top of the compartment.

This is a type Y appliance, which means it is freestanding and can be fitted with cabinets on one or both sides. It may also be fitted in a corner setting.

Sidewalls, which are above hob level, should be protected by heat resistant non- combustible material and must not be nearer than 40mm to the hob side.

A nominal air gap of 2mm at either side of the appliance is required to enable the appliance to be moved into position.

Always ensure an air gap is maintained at hotplate level. Tiles or other forms of deep wall covering should not obscure this gap.

Overhanging surfaces or a cooker hood should be a minimum of 685mm above the hob.

40 min

685 min

22

It is important to ensure that the appliance is level after installation. Levelling feet are fitted to the appliance to accommodate uneven floors.

Connecting to the electricity supply

WARNING!

This appliance must be earthed. Do not earth this appliance to gas supply piping. Connect to 230 - 240V AC supply only.

Connection to the electricity supply must be carried out by a qualified electrician/competent person.

The electrical connection should be made using a double pole isolating switch (cooker socket) with at least 3mm contact separation in all poles. The cable must have conductors of sufficiently high cross- sectional area to prevent overheating and deterioration.

35

Image 35
Contents User Manual Cooker Contents During use Important safety instructionsInstallation Child safetyExtreme care must be taken when using a ceramic hob scraper Cleaning and maintenanceControls and their functions Product descriptionTouch control sensors Before using the applianceSwitching the hob on/off Rating plateCondensation and steam Switching the oven on/offCookware Operating timeGrill and oven furniture To set the countdown Electronic timerTo set the time of day To set the oven timer control To cancel the countdownTo set the timer to switch on and off automatically To set the timer to switch off onlyTurn off the oven controls Automatic cookingTo return the appliance to manual Things to noteOperation Ceramic hob Using the hobUsing the stop + go function Using the hob timerSelecting a cooking zone Setting the timeSwitching off the acoustic signal Safety cut-outTo fit the top oven shelf Top oven intelligent grill Using intelligent grillResidual heat HOB Always remove the grill pan handle during grilling Grill pan and handleEnsure the handle is correctly located Top oven Using the top ovenTo fit the main oven shelves Using main oven fan cookingMain oven grill Main oven fan cookingActivating the child lock Using defrostChild lock DefrostFunction lock Temperature reviewOven Safety cut-out Switching on after a safety cut- outFood Grilling chartTOP Oven Food POS Cooking Approx Temp C Top oven cooking chartFood TOP Oven POS Cooking Approx Temp C Food Cooking Approx Temp C Main oven cooking chartMain oven cooking chart Cooking Time Roasting chartMeattemperature Hints and tips Hints and tips when using the hobHints and tips when defrosting Care and cleaning Avoid the use Cleaning the grill/oven furnitureCleaning inside the grill and oven compartments To reduce marking of the hobTo remove the glass Cleaning the doorsCleaning between the outer and inner door glass Aerosol cleaners must not be used on Stay- clean surfacesMain Oven To clean the glass door panelsTo replace the door glass Top OvenType of bulb required is a 300C 25 watt small Edison Screw Replacing an oven light bulbPossible Solution TroubleshootingProblem Timer does not work Oven is not cooking evenlyOven light fails to illuminate Oven fan is noisy This appliance must be earthed Installation instructionsConnecting to the electricity supply Ensure that the cover is securely fastened SafetyWe recommend you use a new length Mains terminal coverEnvironment Technical detailsStandard guarantee conditions Guarantee / Customer carePage 349151003 04/2007