Frigidaire 318201616 Important Safety Warning, Anti-Tip Brackets Installation Instructions

Page 10

30" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

8.Important Safety Warning

To reduce the risk of tipping of the range, the range must be secured to the floor by properly installed anti-tip brackets and screws packed with the range. Those parts are located in a plastic bag in the oven. Failure to install the anti-tip brackets will allow the range to tip over if excessive weight is placed on an open door or if a child climbs upon it. Serious injury might result from spilled hot liquids or from the range itself.

Follow the instructions below to install the anti-tip brackets.

If range is ever moved to a different location, the anti- tip brackets must also be moved and installed with the range. To check for proper installation, see step 5.

Tools Required:

5/16"(0,79 cm) Nutdriver or Flat Head Screwdriver Adjustable Wrench

Electric Drill

3/16"(0,5 cm) Diameter Drill Bit

3/16"(0,5 cm) Diameter Masonry Drill Bit (if installing in concrete)

Anti-Tip Brackets Installation Instructions

Brackets attach to the floor at the back of the range to hold both rear leg levelers. When fastening to the floor, be sure that screws do not penetrate electrical wiring or plumbing. The screws provided will work in either wood or concrete.

Anti-Tip Bracket

Back Edge of

Range or Rear Wall

CL

 

 

9 1/8”

 

18¼”

(23.2 cm)

(46.4 cm)

Anti-Tip

28 1/8”

(71.4 cm)

Bracket

(Rear width of range

with body sides)

1.Unfold paper template and place it flat on the floor with the back and side edges positioned exactly where the back and sides of range will be located when installed. (Use the diagram below to locate brackets if template is not available.)

2.Mark on the floor the location of the 4 mounting holes shown on the template. For easier installation, 3/16" (0.5 cm) diameter pilot holes 1/2" (1.3 cm) deep can be drilled into the floor.

3.Remove template and place brackets on floor with turned up flange to the front. Line up holes in brackets with marks on floor and attach with 4 screws provided. Brackets must be secured to solid floor. If attaching to concrete floor, first drill 3/16" (0.5 cm) dia. pilot holes using a masonry drill bit.

4.Level range if necessary, by adjusting 4 leg levelers with wrench. (See Figure 10 below.) A minimum clearance of 1/8" (0.8 cm) is required between the bottom of the range and the rear leg levelers to allow room for the anti-tip brackets.

5.Slide range into place making sure rear legs are trapped by ends of brackets. Range may need to be shifted slightly to one side as it is being pushed back to allow rear legs to align with brackets. You may also grasp the top rear edge of the range and carefully attempt to tilt it forward to make sure range is properly anchored.

Leveling Leg

Raise

Lower

Figure 10

 

Slide

Figure 9

Back

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents These surfaces should be flat Leveled hatched areaImportant Cabinet and countertop By the leveling legs and not by the cooktop itselfWidth should match the cutout width Raised ShaveEdge To Clear Space for a 31½ 81 cm Wide Cooktop Important Note to the Consumer Important Notes to the InstallerInstall anti- tip device packed with range Serial Plate LocationAccess to Terminal Block & Grounding Strap U.S.A Factory Connected Power Supply Cord Canada onlyPower Supply Cord Kit U.S.A Electrical Shock HazardThree Conductor Wire Connection to Range Four Conductor Wire Connection to RangeBlack WiresCable from Residence BoxCabinet Construction Range InstallationCountertop Preparation Leveling the Range When All Hookups are CompleteBefore You Call for Service Check OperationAnti-Tip Brackets Installation Instructions Important Safety WarningTools Required Approx 7/8 CanadáVea la nota 55.25 cmPuerta abierta Panel lateralDemetal Reborde delvidrio Lime el ½ Max BordeNúmero Nota importante para el consumidor Notas importantes para el instaladorEncontrará el modelo y el Peligro de choque eléctrico Estuche de cable del suministro eléctrico U.S.AEléctricos Conexión del cable a tres alambres la cocina Conexión eléctrica a la cocina Estados UnidosConexión del cable de cuatro conductores a la cocina Alambre neutral blanco juntos Desconecte el suministro eléctricoAlambres vea figura Conecte los dos alambres negros juntosInstalación sin paneles laterales Preparación del mostradorInstalación con un protector trasero Ubicación del Número de Modelo y de Serie Comprobación del FuncionamientoDespués de Terminar la Instalación Antes de Llamar al ServicioInstrucciones de Instalación del Soporte Antivuelco SeguridadHerramientas Necesarias Pour Votre Sécurité N’entreposez pas ou n’utilisez pas Niveau région hachuréeTout autre appareil électroménager Panneau latéral 22 7/8 58,1 cm min 23 1/4 59,05 cm max See note 86 cmComptoir à Arasez leDessus du Au moinsEmplacement de la plaque signalétique ’oubliez pas de laisser ces instructions au consommateurAccès au bloc de connexions et à la plaque de mise à terre Ensemble de cordon dalimentation États-UnisRisque de choc électrique Gauche Cuisinière U.S.ARouge à la borne de droite, et le fil noir à la borne de Abaissez le couvercle des bornes du bloc deDe lappareil et le fil neutre blanc du câble Débranchez lalimentationReliez ensemble, le fil blanc, le fil vert dénudé DalimentationInstallation de la cuisinière Préparation du dessus de comptoirMise à niveau de la cuisinière Emplacement des numéros de modèle et de sérieAvant d’appeler le service d’entretien Vérification du FonctionnementOutils Requis Instructions d’installation des supports anti‑basculeImportantes Tourne‑écrou de 5 /160,79 cm ou tournevis à tête carréeInstructions Dinstallation Pour LA Cuisinière 30 Encastrable Instructions Dinstallation Pour LA Cuisinière 30 Encastrable

318201616 specifications

The Frigidaire 318201616 is a highly regarded appliance component primarily known for its role as an oven control board. Designed to offer reliability and efficient performance, this part is a vital component for various models of Frigidaire ovens, ensuring consistent cooking results and enhancing the overall kitchen experience.

One of the key features of the Frigidaire 318201616 is its user-friendly interface. The control board is equipped with clear indicators that allow users to easily navigate through different cooking modes and settings. This simplifies the cooking process, making it accessible even for individuals who may not be familiar with complex oven functions.

The technology integrated into the Frigidaire 318201616 includes advanced electronic circuitry, which provides precise temperature control. This ensures that dishes are cooked evenly and at the desired temperature, reducing the chances of undercooking or overcooking. The unit also includes built-in safety features to prevent overheating, which is essential for maintaining kitchen safety.

Another important characteristic of this control board is its compatibility with various Frigidaire oven models. This versatility is advantageous for users who may need to replace their oven control board, as it allows for easy installation and a reliable fit. The part is constructed with quality materials that enhance its durability, ensuring longevity even with regular use.

The installation of the Frigidaire 318201616 is straightforward and often requires only basic tools, making it a feasible DIY project for many homeowners. Therefore, it provides a cost-effective solution for those who may want to avoid the expenses associated with professional repairs.

In summary, the Frigidaire 318201616 control board is an essential component that enhances the functionality of Frigidaire ovens. With its user-friendly interface, advanced temperature control technology, broad compatibility, and durable construction, it stands out as a reliable choice for anyone looking to maintain or improve their kitchen appliances. Whether you are an avid home cook or someone who occasionally uses the oven, this control board ensures that your cooking experience is smooth and efficient.
Top Page Image Contents