Frigidaire 318201616 Factory Connected Power Supply Cord Canada only, Power Supply Cord Kit U.S.A

Page 5

30" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

1.Factory Connected Power Supply Cord (Canada only)

This range is equipped with a factory-connected power cord (see Figure 1). Cord must be connected to a grounded 120/240 volt or 120/208 volt range outlet with a 50A recommended circuit (minimum 40A). If no outlet is available, have one installed by a qualified electrician.

Canada Style

Figure 1

2. Power Supply Cord Kit (U.S.A.)

The user is responsible for connecting the power supply cord to the connection block located behind the back panel access cover.

This appliance may be connected by means of permanent "hard wiring"; flexible armored or nonmetallic shielded copper cable (when local code allow it) or by means of a power supply cord kit.

NOTE: Electric Slide-in Range is shipped from factory with 1 1/8" (2.9 cm) dia. hole as shown on figure 4. If a larger hole is required, punch out the knockout.

Risk of fire or electrical shock exists if an incorrect size range cord kit is used, the Installation Instructions are not followed, or the strain relief bracket is discarded.

For mobile homes, new installations or recreational vehicles, use only a power supply kit designed for a range at 125V/250V 50A recommended (minimum

40A). Cord must have either 3 (when local code permits grounding through neutral) or 4 conductors. Terminal on end of wires must be either closed loop or open spade lug with upturned ends. Cord must have strain-relief clamp.

Do not loosen the nuts which secure the factory-installed range wiring to terminal block while connecting range. Electrical failure or loss of electrical connection may occur.

Electrical Shock Hazard

•Electrical ground is required on this appliance.

•Do not connect to the electrical supply until appliance is permanently grounded.

•Disconnect power to the circuit breaker or fuse box before making the electrical connection.

•This appliance must be connected to a grounded, metallic, permanent wiring system, or a grounding connector should be connected to the grounding terminal or wire lead on the appliance.

Failure to do any of the above could result in a fire, personal injury or electrical shock.

3.Access to Terminal Block & Grounding Strap (U.S.A.)

BEND REAR WIRE COVER HERE

FOR ACCESS TO TERMINAL BLOCK

Figure 2

This appliance is manufactured with the frame grounded by connection of a grounding strap between the neutral power supply terminal and the frame. If used in USA, in a new branch circuit installation (1996 NEC), mobile home or recreational vehicule, where local code do not permit grounding through neutral (white) wire or in Canada; remove the grounding strap from the frame and cut the other end, near the neutral terminal. Connect the appliance in usual manner.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Leveled hatched area These surfaces should be flatWidth should match the cutout width By the leveling legs and not by the cooktop itselfImportant Cabinet and countertop Edge To Clear Space for a 31½ 81 cm Wide Cooktop ShaveRaised Install anti- tip device packed with range Important Notes to the InstallerImportant Note to the Consumer Serial Plate LocationPower Supply Cord Kit U.S.A Factory Connected Power Supply Cord Canada onlyAccess to Terminal Block & Grounding Strap U.S.A Electrical Shock HazardFour Conductor Wire Connection to Range Three Conductor Wire Connection to RangeCable from Residence WiresBlack BoxCountertop Preparation Range InstallationCabinet Construction Before You Call for Service When All Hookups are CompleteLeveling the Range Check OperationTools Required Important Safety WarningAnti-Tip Brackets Installation Instructions Canadá Approx 7/8Puerta abierta 55.25 cmVea la nota Panel lateralNúmero Lime el ½ Max BordeDemetal Reborde delvidrio Encontrará el modelo y el Notas importantes para el instaladorNota importante para el consumidor Eléctricos Estuche de cable del suministro eléctrico U.S.APeligro de choque eléctrico Conexión del cable de cuatro conductores a la cocina Conexión eléctrica a la cocina Estados UnidosConexión del cable a tres alambres la cocina Alambres vea figura Desconecte el suministro eléctricoAlambre neutral blanco juntos Conecte los dos alambres negros juntosInstalación con un protector trasero Preparación del mostradorInstalación sin paneles laterales Después de Terminar la Instalación Comprobación del FuncionamientoUbicación del Número de Modelo y de Serie Antes de Llamar al ServicioHerramientas Necesarias SeguridadInstrucciones de Instalación del Soporte Antivuelco Tout autre appareil électroménager Niveau région hachuréePour Votre Sécurité N’entreposez pas ou n’utilisez pas 22 7/8 58,1 cm min 23 1/4 59,05 cm max See note 86 cm Panneau latéralDessus du Arasez leComptoir à Au moins’oubliez pas de laisser ces instructions au consommateur Emplacement de la plaque signalétiqueRisque de choc électrique Ensemble de cordon dalimentation États-UnisAccès au bloc de connexions et à la plaque de mise à terre Rouge à la borne de droite, et le fil noir à la borne de Cuisinière U.S.AGauche Abaissez le couvercle des bornes du bloc deReliez ensemble, le fil blanc, le fil vert dénudé Débranchez lalimentationDe lappareil et le fil neutre blanc du câble DalimentationPréparation du dessus de comptoir Installation de la cuisinièreAvant d’appeler le service d’entretien Emplacement des numéros de modèle et de sérieMise à niveau de la cuisinière Vérification du FonctionnementImportantes Instructions d’installation des supports anti‑basculeOutils Requis Tourne‑écrou de 5 /160,79 cm ou tournevis à tête carréeInstructions Dinstallation Pour LA Cuisinière 30 Encastrable Instructions Dinstallation Pour LA Cuisinière 30 Encastrable

318201616 specifications

The Frigidaire 318201616 is a highly regarded appliance component primarily known for its role as an oven control board. Designed to offer reliability and efficient performance, this part is a vital component for various models of Frigidaire ovens, ensuring consistent cooking results and enhancing the overall kitchen experience.

One of the key features of the Frigidaire 318201616 is its user-friendly interface. The control board is equipped with clear indicators that allow users to easily navigate through different cooking modes and settings. This simplifies the cooking process, making it accessible even for individuals who may not be familiar with complex oven functions.

The technology integrated into the Frigidaire 318201616 includes advanced electronic circuitry, which provides precise temperature control. This ensures that dishes are cooked evenly and at the desired temperature, reducing the chances of undercooking or overcooking. The unit also includes built-in safety features to prevent overheating, which is essential for maintaining kitchen safety.

Another important characteristic of this control board is its compatibility with various Frigidaire oven models. This versatility is advantageous for users who may need to replace their oven control board, as it allows for easy installation and a reliable fit. The part is constructed with quality materials that enhance its durability, ensuring longevity even with regular use.

The installation of the Frigidaire 318201616 is straightforward and often requires only basic tools, making it a feasible DIY project for many homeowners. Therefore, it provides a cost-effective solution for those who may want to avoid the expenses associated with professional repairs.

In summary, the Frigidaire 318201616 control board is an essential component that enhances the functionality of Frigidaire ovens. With its user-friendly interface, advanced temperature control technology, broad compatibility, and durable construction, it stands out as a reliable choice for anyone looking to maintain or improve their kitchen appliances. Whether you are an avid home cook or someone who occasionally uses the oven, this control board ensures that your cooking experience is smooth and efficient.
Top Page Image Contents