Frigidaire 318201616 installation instructions Three Conductor Wire Connection to Range

Page 6

30" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

4. Electrical Connection to the Range

(U.S.A.)

Three Conductor Wire Connection to Range

If local codes permit connection of the frame grounding conductor to the neutral wire of the copper power supply cord (see Figure 3):

1.Remove the 3 screws at the lower end of the rear wire cover, then bend the lower end of the rear wire cover (access cover) upward to expose range terminal connection block (see Figure 2).

2.Using the nuts supplied in the literature package, connect the neutral of the copper power supply cord to the center silver-colored terminal of the terminal block, and connect the other wires to the outer terminals. Match wires and terminals by color (red wires connected to the right terminal, black wires connected to the left terminal) (see figure 3).

3.Lower the terminal cover and replace the 3 screws.

Silver Colored Terminal

Red Wire

Terminal

Cord

Block

Mounting

 

 

Plate

Black

Neutral

Wire

(White Wire)

 

Grounding

 

Strap

A User Supplied

 

1 1/8" (2.9 cm) Dia.

 

Direct Connection

Strain-relief Must

 

To 240 V

Hole. Punch Out

Be Installed at This

Knockout for 1 3/8"

Location.

Receptacle

(3.5 cm) Dia. Cord

 

 

 

Figure 3

Kit Hole.

 

 

Four Conductor Wire Connection to Range

Where local codes does NOT permit connection of the frame grounding conductor to the neutral wire of the copper power supply cord (see Figure 4):

1.Remove the 3 screws at the lower end of the rear wire cover, then raise the lower end of the rear wire cover (access cover) upward to expose range terminal connection block (see figure 2).

2.Remove the grounding strap from the terminal block and from the appliance frame.

3.Using the nuts supplied with the literature package, connect the ground wire (green) of the copper power supply cord to the frame of the appliance with the ground screw, using the hole in the frame where the ground strap was removed (see Figure 4).

4.Connect the neutral of the copper power supply cord to the center silver-colored terminal of the terminal block, and connect the other wires to the outer terminals. Match wires and terminals by color (red wires connected to the right terminal, black wires connected to the left terminal).

5.Lower the terminal cover and replace the 3 screws.

Terminal Block

Silver Colored Terminal

Red

Wire

Black Wire

 

1 1/8" (2.9cm)

 

Dia. Direct

 

Connection

 

Hole. Punch

Neutral

Out Knockout

(White Wire)

for 1 3/8"

Ground (Bare

(3.5cm) Dia.

Cord Kit Hole.

Copper Wire)

A User Supplied

 

Strain-relief Must

 

Be Installed at This

 

Location

To 240 V Receptacle

NOTE: Be sure to remove the supplied grounding strap.

Figure 4

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents These surfaces should be flat Leveled hatched areaBy the leveling legs and not by the cooktop itself Important Cabinet and countertopWidth should match the cutout width Shave RaisedEdge To Clear Space for a 31½ 81 cm Wide Cooktop Important Note to the Consumer Important Notes to the InstallerInstall anti- tip device packed with range Serial Plate LocationAccess to Terminal Block & Grounding Strap U.S.A Factory Connected Power Supply Cord Canada onlyPower Supply Cord Kit U.S.A Electrical Shock HazardThree Conductor Wire Connection to Range Four Conductor Wire Connection to RangeBlack WiresCable from Residence BoxRange Installation Cabinet ConstructionCountertop Preparation Leveling the Range When All Hookups are CompleteBefore You Call for Service Check OperationImportant Safety Warning Anti-Tip Brackets Installation InstructionsTools Required Approx 7/8 CanadáVea la nota 55.25 cmPuerta abierta Panel lateralLime el ½ Max Borde Demetal Reborde delvidrioNúmero Notas importantes para el instalador Nota importante para el consumidorEncontrará el modelo y el Estuche de cable del suministro eléctrico U.S.A Peligro de choque eléctricoEléctricos Conexión eléctrica a la cocina Estados Unidos Conexión del cable a tres alambres la cocinaConexión del cable de cuatro conductores a la cocina Alambre neutral blanco juntos Desconecte el suministro eléctricoAlambres vea figura Conecte los dos alambres negros juntosPreparación del mostrador Instalación sin paneles lateralesInstalación con un protector trasero Ubicación del Número de Modelo y de Serie Comprobación del FuncionamientoDespués de Terminar la Instalación Antes de Llamar al ServicioSeguridad Instrucciones de Instalación del Soporte AntivuelcoHerramientas Necesarias Niveau région hachurée Pour Votre Sécurité N’entreposez pas ou n’utilisez pasTout autre appareil électroménager Panneau latéral 22 7/8 58,1 cm min 23 1/4 59,05 cm max See note 86 cmComptoir à Arasez leDessus du Au moinsEmplacement de la plaque signalétique ’oubliez pas de laisser ces instructions au consommateurEnsemble de cordon dalimentation États-Unis Accès au bloc de connexions et à la plaque de mise à terreRisque de choc électrique Gauche Cuisinière U.S.ARouge à la borne de droite, et le fil noir à la borne de Abaissez le couvercle des bornes du bloc deDe lappareil et le fil neutre blanc du câble Débranchez lalimentationReliez ensemble, le fil blanc, le fil vert dénudé DalimentationInstallation de la cuisinière Préparation du dessus de comptoirMise à niveau de la cuisinière Emplacement des numéros de modèle et de sérieAvant d’appeler le service d’entretien Vérification du FonctionnementOutils Requis Instructions d’installation des supports anti‑basculeImportantes Tourne‑écrou de 5 /160,79 cm ou tournevis à tête carréeInstructions Dinstallation Pour LA Cuisinière 30 Encastrable Instructions Dinstallation Pour LA Cuisinière 30 Encastrable

318201616 specifications

The Frigidaire 318201616 is a highly regarded appliance component primarily known for its role as an oven control board. Designed to offer reliability and efficient performance, this part is a vital component for various models of Frigidaire ovens, ensuring consistent cooking results and enhancing the overall kitchen experience.

One of the key features of the Frigidaire 318201616 is its user-friendly interface. The control board is equipped with clear indicators that allow users to easily navigate through different cooking modes and settings. This simplifies the cooking process, making it accessible even for individuals who may not be familiar with complex oven functions.

The technology integrated into the Frigidaire 318201616 includes advanced electronic circuitry, which provides precise temperature control. This ensures that dishes are cooked evenly and at the desired temperature, reducing the chances of undercooking or overcooking. The unit also includes built-in safety features to prevent overheating, which is essential for maintaining kitchen safety.

Another important characteristic of this control board is its compatibility with various Frigidaire oven models. This versatility is advantageous for users who may need to replace their oven control board, as it allows for easy installation and a reliable fit. The part is constructed with quality materials that enhance its durability, ensuring longevity even with regular use.

The installation of the Frigidaire 318201616 is straightforward and often requires only basic tools, making it a feasible DIY project for many homeowners. Therefore, it provides a cost-effective solution for those who may want to avoid the expenses associated with professional repairs.

In summary, the Frigidaire 318201616 control board is an essential component that enhances the functionality of Frigidaire ovens. With its user-friendly interface, advanced temperature control technology, broad compatibility, and durable construction, it stands out as a reliable choice for anyone looking to maintain or improve their kitchen appliances. Whether you are an avid home cook or someone who occasionally uses the oven, this control board ensures that your cooking experience is smooth and efficient.
Top Page Image Contents