Olympus P-200 manual Recharging the battery, Battery power operation

Page 35

Notes

•Recharging time varies depending on the remaining battery power and environmental conditions.

•Even when the battery is installed, it is not recharged while the printer is set to ON. Recharging only takes place when the printer is OFF.

•Once you started recharging, it is recommended that you fully recharge the battery without interruption. (Do not turn the printer ON or OFF during recharging.)

•When a fully discharged battery is recharged, a pre-charging period of up to 1 minute takes place before the

ACCESS/CHARGE indicator lights up. (The indicator does not light in the pre-charging period.)

To supply power from the optional rechargeable battery

1.Installing the battery

1)Turn the printer OFF and unplug the AC adapter power cord.

2)Remove the rear cover.

3)Position the battery so that the marking on the battery points in the same direction as the one on the printer. Align the battery with the printer as shown in illustration 3), then push the entire battery toward the printer.

4)While pushing the battery against the printer, slide the battery toward the battery unlock lever until it clicks.

2.Recharging the battery

1)Connect the AC adapter.

2)The ACCESS/CHARGE indicator lights to indicate that recharging has started.

3)Recharging takes about 2.5 hours. The ACCESS/ CHARGE indicator turns off when recharging is complete.

3.Battery power operation

1)Disconnect the AC adapter from the printer and turn the printer ON.

When the AC adapter is connected, the printer is always powered by the AC adapter.

The control panel shows the remaining battery power.

16 Setup

Image 35

Contents 200 User Registration Table of Contents System Requirements Turn on the printer and the PC. Launch Windows Installing the SoftwareConnect the printer to your PC Insert the floppy disk into the PCs floppy drive Select Local printer as the printer connection destination Double-click the AddPrinter iconClick End to complete installation File menu, click Delete UninstallationRun the application and open the images you want to print PrintingClick Print Set the number of prints CopiesClick the name of the queued document you want to cancel To cancel printingWhen the print monitor is displayed Tips for printing Click Properties Split PrintFile menu of the application, click Print Single Set the image quality in the Color adjustment sheet Adjusting the Image QualityJammed, etc Troubleshooting GuideBefore printing Olympus America INC 200 Owners Record Table of Contents Duplication restrictions PrecautionsIntroduction If the power cord is damaged, unplug it Safety precautionsDo not place liquids on the printer Do not damage the power cordDo not install the printer in the following places Do not disassemble or modify the printerDo not use the printer in the following places Connect the power cord correctlyDo not hold the power cord plug with wet hands Do not overload the power outletPage Do not pull the cord with a jerk Do not move the printer when the power cord is tautDo not block the vent Transport the printer carefully Beware of moisture condensationOperate the printer at least once every six months Carry the printer with both handsGetting Started Unpacking the printerHigh-quality overcoated prints What you can do with the P-200 Digital color printerMaking a variety of prints Printing of images from a PCIdentifying the parts Paper Feed Cassette Operation PanelTo supply power from the provided AC adapter Setting up the printerSetup Battery power operation Recharging the batteryRemoving the battery Using print packsRemaining battery power indication Loading the ink ribbon cartridge Remove the ink ribbon cartridge, and then re-insert it If the cartridge compartment lid does not closeTo load a half-used ink ribbon cartridge Handling the ink ribbon cartridgeTo replace an ink ribbon cartridge Loading print paper in the paper feed Cassette Loading print paperStorage precautions Installing the paper feed cassette Onto the printerPrint all-frame print DPOFprint index print PreparationBasic Printing Inserting the card into the printers slot Opening the card coverBasic Printing Never attempt to insert or remove CompactFlash while Digital cameras with a file name display function PrintingTo change the frame number display to file name Display Frame Basic Printing To cancel printing Other Printing Functions Making split printsMaking split prints of the same image Indexprint Frame No. designation AII-frame display All-frame printing Appears on the control panel Printing DPOF-reserved imagesSmartMedia or CompactFlash card. Date printing Printing the dateBefore you begin Adjusting the sharpness For Your Information TroubleshootingIf indicators light or blink Paper is jammed Remove jammed paper. See below If print paper is jammedFor Your Information Storage after printing About the ink ribbon cartridge and print paperPrinter SpecificationsProtection against such interference in a residential FCC noticeAccessories as of October Are not indicated in each case in this manual Print index1100 6MJ