Marathon installation manual Decals for RJ-88SC, RJ-100SC, RJ-250SC, or RJ-250VL

Page 10

1 OPERATION

DECALS for RJ-88SC, RJ-100SC, RJ-250SC, or RJ-250VL

1-8

 

 

WARNING DECAL REQUIREMENTS

When your compactor leaves the factory, several WARNING DECALS are installed for protection. These labels are subject to wear and abuse due to the nature of the refuse handling operation. THESE DECALS MUST BE MAINTAINED. Additional decals may be purchased from your distributor or from Marathon Equipment Company.

Decal Number 06-0002 - RAM JET - MARATHON EQUIPMENT COMPANY

Decal Number 06-0003 - PATENT PENDING

Decal Number 06-0011 - MOTOR ROTATION

Decal Number 06-0038 - CAUTION: DO NOT REMOVE ACCESS COVER EXCEPT FOR SERVICING. FOLLOW LOCK OUT- TAG OUT PROCEDURES.

Decal Number 06-0039 - DANGER: DO NOT ENTER.

Decal Number 06-0040 - CAUTION: KEEP OUT. (used on hoppers)

Decal Number 06-0043 - DANGER: 208 VOLTS, or

Decal Number 06-0044 - DANGER: 230 VOLTS, or

Decal Number 06-0045 - DANGER: 460 VOLTS.

Decal Number 06-0052 - CAUTION: GATE MUST BE CLOSED BEFORE OPERATING COMPACTOR. (used on access gates)

Decal Number 06-0057 - CAUTION: STAND CLEAR WHEN CONTAINER IS BEING LIFTED. Decal Number 06-0058 - ‘A’ PORT

Decal Number 06-0059 - ‘B’ PORT

Decal Number 06-0067 - CAUTION: DO NOT REMOVE THIS CONTAINER UNTIL REAR STOP IS INSTALLED. Decal Number 06-0072 - QUICK CLEAN TANK

Decal Number 06-0093 - FIRE HOSE PORT.

Decal Number 06-0094 - NOTICE: WIPE OFF SEAL AFTER DUMPING.

Decal Number 06-0104 - HYDRAULIC TAILGATE OPERATING INSTRUCTIONS

Decal Number 06-0105 - DANGER: STAND CLEAR OF TAILGATE WHEN LIFTED.

Decal Number 06-0364 - SERIAL NUMBER PLATE

Decal Number 06-0121 - FEDERAL REGULATIONS PROHIBITS THE USE BY PERSONS UNDER 18 YEARS OF AGE.

Decal Number 06-0124 - CYCON

Decal Number 06-0249 - DANGER: HAZARDOUS VOLTAGE ... LOCK OUT & TAG OUT. Decal Number 06-1839 - AMERICAN FLAG

Image 10
Contents Play IT Safe Contents Operation IntroductionSide View SpecificationsWastec PRE-OPERATION Instructions Only Authorized Personnel Should be Allowed InsideEmergency Stop Control Description for 88SC, 100SC, & 250SC Keyed Start Switch ReverseOperator Station Control Description for 250VLCase of Emergency Operating Instructions for RJ-250VL Manual Override Instructions RAM Stop Rear only RJ-250VLOptional Controls Decals for RJ-88SC, RJ-100SC, RJ-250SC, or RJ-250VL Remote Power Unit THRU-THE-WALL Optional Loading ConfigurationsDock Access Gate & Hopper Security ChuteHydraulic Tailgate HT Units Rear ViewMaintenance LOCK-OUT & TAG-OUT InstructionsPeriodic Maintenance Pressure Settings Relief ProceduresPressure Setting SettingRAM Control Timer Adjustment Printe D Circuit Board Locate D I N Motor Control PanelCylinder Removal Instructions MULTI-CYCLE Timer Adjustment OptionWarranty and Service on Motors RAM Stop Forward OptionStandard System Operating CHARACTERISTICS, 5 hp & 10 hp Principles of OperationDoor Seal on Door Tailgate Seal ReplacementFront View Section A-ATimer Settings ChartsFuses and Circuit Breakers Wire Sizes Length SizeParts List Part DescriptionMotor Control Panel Typical Power Unit Standard 5 HP Power Unit Standard 10 HP Hydraulic Schematic Typical TROUBLE-SHOOTING Chart Problem Cause SolutionPump Makes NOISE-SOUNDS Concrete PAD Concrete PAD RequirementsContainer Guides CHUTE-FED Installation Steel Installation ProceduresDock Installation DecalsElectrical & Hydraulic Installation Remote Power Pack InstallationElectrical Connections Pushbutton Operator StationSTART-UP Instructions Power Unit THROUGH-THE-WALL Power Unit InstallationTOP View Compactor Hauler Instructions General See the Next page for Door and Latch Operation InstructionsAuto Relatch Hauler Instructions DOOR/LATCH OperationLatch Side View Container For Optional HT Units Instructions for Using Maintenance BAR Body Between the Tailgate and the ContainerHauler Instructions Liquid Removal For Optional SL Units