Kenmore 10689482996, 2217402A, 10689489997 manual Interior Components, =-t

Page 10

4, Remove dirt and lint from the condenser fins and the unit compartment with a brush attachment on a vacuum cleaner.

5.Replace the lower access panel using the four screws.

6.Plug in ice maker or reconnect power.

Interior Components

1.Unplug ice maker or disconnect power.

2.Open the storage bin door and remove any ice that is in the bin.

3.Remove the drain cap from the water pan and drain thoroughly. Replace the drain cap securely on the water pan. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

4.Remove the two screws that hold the cutter grid cover in place. Remove the cutter grid cover.

5.Unplug the wiring harness from the left side of the cutter grid.

8,

9,

Remove the two thumb screws that hold the water pan in place. Push down with one hand on the front of the pan while pulling forward on the bottom back side.

B

: :

_

A B

 

::-'=-"t _

 

 

 

II

C

 

A. Water pan

 

 

B. Water pan thumb screws

 

 

C. Drain

cap

 

Remove, clean and replace the ice scoop and ice scoop holder.

After removing the ice scoop, remove the holder by removing the two thumb screws.

Wash the ice scoop holder along with the other interior components using the following instructions.

Replace the ice scoop holder by replacing the thumb

screws.

A%i

A. Cutter grid cover

B.Screws

6.Unplug the ice level sensor from the right side of the cutter grid. Pull the ice level sensor down and forward away from the cutter grid.

7.Remove the right-hand and left-hand screws. Lift the cutter grid up and out.

NOTE: Make sure the plastic spacer from the right-hand side of the cutter grid bracket stays with the cutter grid.

A. Thumb screw

B. Ice scoop holder

10.Wash the interior components (cutter grid, exterior of hoses, and water pan) and the storage bin, door gasket, ice scoop, and ice scoop holder with mild soap or detergent and warm water. Rinse in clean water. Then clean the same parts with a solution of 1 tbs (15 mL) of household bleach in 1 gal. (3.8 L) warm water. Rinse again thoroughly in clean water.

NOTE: Do not remove hoses. Do not wash plastic parts in

 

 

dishwasher. They cannot withstand temperatures above

A

=J- O

145°F (63°0).

c

11.

Replace water pan by pushing back on the bottom with one

 

hand while pushing up and back on the top. Secure the water

 

pan by replacing both screws.

 

12.

Check the following:

A. Cutter

grid

Harness

D. Ice level sensor harness

 

B. Screw

 

 

E. Plastic spacer

C. Cutter

grid

 

F. Screw

Drain cap from the water pan is securely in place. If the drain cap is loose, water will empty from the water pan, and you will have either thin ice or no ice.

Hose from water pan is inserted into storage bin drain opening.

13.Slide the cutter grid back into place and secure it by replacing the right-hand screw and plastic spacer. Then tighten the left-hand screw. Reconnect the cutter grid harness and the ice level sensor harness.

14.Replace the cutter grid cover and the two screws.

15.Plug in ice maker or reconnect power.

10

Image 10
Contents Ice Maker Table of Contents WarrantyInstallation Instructions ICE Maker SafetyCleaning Before Use Recommended grounding method Tools neededRead all directions thoroughly before you begin Rear View2cm 1 Gravity Drain SystemDrain Pump System on some models Replace Door Remove DoorReverse Hinges Top HingeICE Maker USE Ice Making ProcessDirty or clogged condenser Exterior SurfacesIce Maker System Waterpan B. Drain capInterior Components =-tPage Ice maker runs but produces no ice TroubleshootingYour ice maker will not operate Thin, soft or clumps of iceProtection Agreements Maintenance AgreementsSears Maintenance Agreement Master Protection AgreementsSolucion Seguridad DE LA F/.BRICA DE Hielo InstruccionesCuidado Nomeros DE Servicio ContraportadaLimpieza Seguridad DE LA Fabrica DE HieloInstrucciones DE Instalacion Uso Cbmo quitar Los materiales de empaqueMtodo recomendado para la conexibn a tierra Suministro de agua de 6smosis inversaImportante Herramientas necesariasLea todas las instrucciones a rondo antes de comenzar Conexibn de la tuberia de aguaVista Lateral Vista PosteriorSistema de desagiJe por gravedad 2cm IHerramientas Necesarias Conexibn del desagi.ieNo use un cable electrico de extensi6n Sacar la puertaBisagra superior Volver a colocar la puertaInvertir el seguro de la puerta USO DE SU Fabrica DE Hielo Proceso de elaboracibn de hieloSistema de la f&brica de hielo Superficies ExterioresCondensador Un condensador sucio u obstruido Piezas interiores Tornillo de mariposa Soporte de la pala para el hielo Solucion DE Problemas La f&brica de hielo funciona pero no produce hieloContratos Maestros de Proteccibn Contratos DE ProteccionHielo delgado, blando o aglutinado Contratos de mantenimientoTable DES Matii RES GarantieEnlvement des matriaux demballage Instructions DinstallationNettoyage avant I utilisation Mthode de mise a la terre recommande Alimentation en eau par osmose inverseIM Portant Outillage ncessaireLire compltement toutes les instructions avant de commencer Outils requisVuelaterale VUE ArriireVidange par gravit Systme avec pompe de vidange sur certains modulesOutillage Nccessaire Raccordement du conduit dvacuationUtiliser deux ou plus de personnes pour deplacer et Dpose de la porteInversion du Ioquet de porte Machine a GlaqonsFabrication de la glace Surfaces extrieures Entretien DE LA Machine GLA ONSNettoyage du systme de la machine & gla£ons Condenseur Un condenseur sale ou bouch Bac a eau Capuchon de vidangeNettoyage des composants intrieurs II-C Machine glaons avec pompe de drainage Eau dans le rservoir Dborde-t-elle?Le capuchon de vidange est-ilbien en place? Si le T-il une accumulation de tartre dans la machineGlaons minces, mous ou agglomrs Verification annuelle dentretien prventif sur demande Contrats DE ProtectionContrats principaux de protection Le contrat dentrstien SearsYour Home 2217402A