Kenmore 2217402A, 10689482996 ICE Maker Safety, Installation Instructions, Cleaning Before Use

Page 3

ICE MAKER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING." These words mean:

You can be killed or seriously injured if you don'timmediately follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

 

 

 

 

IMPORTANT

SAFETY INSTRUCTIONS

 

 

 

 

 

WARNING:

To reduce

the

risk of fire, electric

shock, or injury when

using your

ice

maker,

follow these

basic

precautions:

 

 

 

 

 

 

 

 

 

 

 

 

 

Plug into

a grounded 3 prong

outlet.

Disconnect

power

before

cleaning.

 

 

Do not remove ground

prong.

 

Disconnect

power

before

servicing.

 

Do not use an adapter.

 

 

Replace

all parts

and

panels

before operating.

 

Do not use an extension

cord.

 

 

 

Use two

or more

people

to

move

and install ice

maker.

 

 

 

 

 

SAVE THESE INSTRUCTIONS

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install ice maker. Failure to do so can result in back or other injury.

Removing Packaging Materials

Remove tape and glue from your ice maker before using.

To remove any remaining tape or glue, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water

and dry.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your ice maker.

Cleaning Before Use

After you remove all of the packaging materials, clean the inside of your ice maker before using it. See the cleaning instructions in the Ice Maker Care section.

To ensure proper ventilation for your ice maker, the front side must be completely unobstructed. The unit may be closed-in on the top and three sides, but the installation should allow the ice maker to be pulled forward for servicing if necessary.

Installation of the ice maker requires a cold water supply inlet of 1/4"(6.35 mm) OD soft copper tubing with a shutoff valve and either a gravity-drain system or condensate pump to carry the water to an existing drain.

Choose a well ventilated area with temperatures above 55°F (13°C) and below 100°F (38°C). Best results are obtained between 70°F (21 °C) and 90°F (32°C).

This unit must be installed in an area protected from the elements, such as wind, rain, water spray, or drip.

Image 3
Contents Ice Maker Warranty Table of ContentsICE Maker Safety Installation InstructionsCleaning Before Use Tools needed Recommended grounding methodRear View Read all directions thoroughly before you beginGravity Drain System 2cm 1Drain Pump System on some models Top Hinge Remove DoorReverse Hinges Replace DoorIce Making Process ICE Maker USEWaterpan B. Drain cap Exterior SurfacesIce Maker System Dirty or clogged condenser=-t Interior ComponentsPage Thin, soft or clumps of ice TroubleshootingYour ice maker will not operate Ice maker runs but produces no iceMaster Protection Agreements Maintenance AgreementsSears Maintenance Agreement Protection AgreementsNomeros DE Servicio Contraportada Seguridad DE LA F/.BRICA DE Hielo InstruccionesCuidado SolucionUso Cbmo quitar Los materiales de empaque Seguridad DE LA Fabrica DE HieloInstrucciones DE Instalacion LimpiezaSuministro de agua de 6smosis inversa Mtodo recomendado para la conexibn a tierraConexibn de la tuberia de agua Herramientas necesariasLea todas las instrucciones a rondo antes de comenzar Importante2cm I Vista PosteriorSistema de desagiJe por gravedad Vista LateralSacar la puerta Conexibn del desagi.ieNo use un cable electrico de extensi6n Herramientas NecesariasVolver a colocar la puerta Bisagra superiorInvertir el seguro de la puerta Proceso de elaboracibn de hielo USO DE SU Fabrica DE HieloSuperficies Exteriores Sistema de la f&brica de hieloCondensador Un condensador sucio u obstruido Piezas interiores Tornillo de mariposa Soporte de la pala para el hielo La f&brica de hielo funciona pero no produce hielo Solucion DE ProblemasContratos de mantenimiento Contratos DE ProteccionHielo delgado, blando o aglutinado Contratos Maestros de ProteccibnGarantie Table DES Matii RESInstructions Dinstallation Enlvement des matriaux demballageNettoyage avant I utilisation Alimentation en eau par osmose inverse Mthode de mise a la terre recommandeOutils requis Outillage ncessaireLire compltement toutes les instructions avant de commencer IM PortantSystme avec pompe de vidange sur certains modules VUE ArriireVidange par gravit VuelateraleDpose de la porte Raccordement du conduit dvacuationUtiliser deux ou plus de personnes pour deplacer et Outillage NccessaireMachine a Glaqons Inversion du Ioquet de porteFabrication de la glace Entretien DE LA Machine GLA ONS Surfaces extrieuresNettoyage du systme de la machine & gla£ons Bac a eau Capuchon de vidange Condenseur Un condenseur sale ou bouchNettoyage des composants intrieurs II-C Eau dans le rservoir Dborde-t-elle? Machine glaons avec pompe de drainageT-il une accumulation de tartre dans la machine Le capuchon de vidange est-ilbien en place? Si leGlaons minces, mous ou agglomrs Le contrat dentrstien Sears Contrats DE ProtectionContrats principaux de protection Verification annuelle dentretien prventif sur demande2217402A Your Home