Makita EG511AE, EG301A, EG711AE, EG381AE, EG781AE manual Wattage Information, - 21-

Page 26

6. WATTAGE INFORMATION

Some appliances need a "surge" of energy when starting.

This means that the amount of electrical power needed to start the appliance may exceed the amount needed to maintain its use.

Electrical appliances and tools normally come with a label indicating voltage, cycles / Hz, amperage (amps) and electrical power needed to run the appliance or tool.

Check with your nearest dealer or service center with questions regarding power surge of certain appliances or power tools.

Electrical loads such as incandescent lamps and hot plates require the same wattage to start as is needed to maintain use.

Loads such as fluorescent lamps require 1.2 to 2 times the indicated wattage during start-up.

Loads for mercury lamps require 2 to 3 times the indicated wattage during start-up.

Electrical motors require a large starting current. Power requirements depend on the type of motor and its use. Once enough "surge" is attained to start the motor,

the appliance will require only 50% to 30% of the wattage to continue running.

Most electrical tools require 1.2 to 3 times their wattage for running under load during use. For example, a 5,000 watt generator can power a 1800 to 4000 watt electrical tool.

Loads such as submersible pumps and air compressors require a very large force to start. They need 3 to 5 times the normal running wattage in order to start.

For example, a 5,000 watt generator would only be able to drive a 1,000 to 1,700 watt pump.

NOTE :

The following wattage chart is general guide only. Refer to your specific appliance for correct wattage.

To determine the total wattage required to run a particular electrical appliance or tool, multiply the voltage figure of the appliance/tool by the amperage (amps) figure of same. The voltage and amperage (amps) information can be found on a name plate which is normally attached to electrical appliances and tools.

ENGLISH

Applications

 

Applicable Wattage(W)

 

 

 

 

 

 

EG301A

EG381A

EG511A

EG711A

EG781A

 

 

EG381AE

EG511AE

EG711AE

EG781AE

 

 

Incandescent lamp, Heater

2400

2900

4200

5000

6000

 

 

 

 

 

 

Fluorescent lamp, Electric tool

1300

1600

2300

2750

3300

 

 

 

 

 

 

Mercury lamp

950

1150

1700

2000

2400

 

 

 

 

 

 

Pump, Compressor

600

700

1050

1250

1500

 

 

 

 

 

 

21

Image 26
Contents EG series AIR Index Page Foreword [CAUTION]Contents Safety Precautions - 1-- 2- Specifications - 3-Components - 4-EG711A, EG711AE, EG781A, EG781AE - 5-- 6- - 7- PRE-OPERATION ChecksCheck Engine OIL - 8- Check Engine FuelUp to Level position - 9- Checking Component PartsCheck Generator Surroundings To positive + terminal Grounding GeneratorCable first - 10-- 11- Operating ProceduresStarting the Generator Recoil starter model Electric starter model- 13- Using Electric Power - 14-To take power out from the Twist - 15-Gfci Receptacle - 16-Full Power Switch Except EG301A - 17-Connection of exclusive DC cable Only for charging 12 volt batteryDC Circuit Breaker - 18-Battery Charging Procedures - 19-[Recoil starter model] Stopping the GeneratorOIL Sensor [Electric starter model]Wattage Information - 21-Voltage Drop in Electric Extension Cords - 22-Spark Arrester - 23-Daily Inspection Maintenance SchedulePeriodic Maintenance - 24-Periodic Maintenance Schedule table - 25-Engine OIL Change HOW-TO MaintenanceServicing the AIR Cleaner - 26-- 27- Cleaning and Adjusting Spark PlugCleaning Fuel Strainer Checking Carbon Brush - 28-Disassembly - 29-Preparation for Storage - 30-When No Electricity Is Generated at Receptacle TroubleshootingWhen Engine Fails to Start - 31-- 32- Wiring DiagramEG301A 60Hz-120V EG381A 60Hz-120/240V - 33-EG381AE 60Hz-120/240V Grn/Y Earth Ground terminalEG511A, EG711A, EG781A 60Hz-120/240V - 35-EG511AE, EG711AE, EG781AE 60Hz-120/240V - 36-Makita Corporation