| Rear Support Continued... |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
| Sound Framing Members |
|
|
| ||||
Tools Needed: | To adjust spring tension, fully close | |||||||||||||
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| ||||
| door. Apply vice clamps to track above |
|
|
|
|
|
|
|
|
|
|
| ||
| third roller. Insert a winding bar into |
|
|
|
|
|
|
|
|
|
|
| ||
| the winding cone. Push upward on the |
|
|
|
|
|
|
|
|
|
|
| ||
| winding bar while carefully loosening the |
|
|
|
|
|
|
|
|
|
|
| ||
|
| perforated |
|
|
|
|
|
| ||||||
| set screws in the winding cone. |
|
|
| perforated ANGLE | |||||||||
|
| ANGLE BRACE |
|
| ||||||||||
|
|
|
|
|
|
|
| USING (2) 5/16” X | ||||||
| BE PREPARED TO SUPPORT THE FULL |
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
| HEX HEAD LAG SCREWS | ||||
| FORCE OF THE TORSION SPRING ONCE |
|
|
|
|
|
|
|
|
| TO CEILING MEMBER AND | |||
| THE SET SCREWS ARE LOOSE. Carefully |
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| PARALLEL TO WIDTH OF DOOR | ||||||
| adjust spring tension 1/4 turn. Retighten |
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| |||
| both set screws in the winding cone and |
|
|
|
|
|
|
|
|
|
|
| ||
| repeat for the other side. Recheck door |
|
|
|
|
|
|
|
|
| BOLT MUST EXTEND INTO | |||
| balance DO NOT ADJUST MORE THAN | HORIZONTAL TRACK |
|
| ||||||||||
| 1/2 TURN FROM THE RECOMMENDED |
|
|
|
|
|
|
|
|
| THE TRACK TO SERVE AS | |||
| NUMBER OF TURNS. If door still does not |
|
|
|
|
|
|
|
|
| A ROLLER STOP | |||
| balance correctly, contact a qualified door |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| agency. |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |||||
| If the door still does not operate easily, |
|
|
|
| Sound Framing Members |
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| |||
| lower the door into the closed position, |
|
|
|
|
|
|
|
|
|
|
| ||
| UNWIND THE SPRING(S) FULLY and |
|
|
|
|
|
|
|
|
|
|
| ||
| recheck the following items: |
|
|
|
|
|
|
|
|
|
|
| ||
| 1.) Check the door for level. |
|
|
|
|
|
|
| ||||||
|
|
| ANGLE BRACE |
|
|
|
|
| ||||||
| 2.) Check the torsion tube for level. |
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| perforated ANGLE |
| |||||
|
|
|
|
|
|
|
|
| ||||||
| 3.) Check the track spacing. |
|
|
|
|
|
|
|
| USING (2) 5/16” X |
| |||
| 4.) Check the counterbalance cables for |
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| HEX HEAD LAG SCREWS |
| |||
| equal tension (drums must be equallly |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| TO CEILING MEMBER AND |
| ||||
| raped before spring winding). |
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| PARALLEL TO WIDTH OF DOOR |
| |||||
| 5.) Check the track for potential |
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
| |||
| obstruction of the rollers. | HORIZONTAL TRACK |
|
| BOLT MUST EXTEND INTO | |||||||||
| 6.) Clamp vice clamps onto track and |
|
|
|
|
|
|
|
|
| ||||
| rewind springs |
|
|
|
|
|
|
|
|
| THE TRACK TO SERVE AS | |||
| IMPORTANT: If door still does not |
|
|
|
|
|
|
|
|
|
| A ROLLER STOP | ||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
| PERFORATED ANGLE |
|
|
|
| ||||||
| operate properly, then contact a |
|
|
|
|
|
| |||||||
| trained door system technician. |
|
|
|
|
|
|
|
|
|
|
|
(3)5/16” BOLTS
&NUTS
back hangers.
Doors over 16’ high use 2 intermediate hangers.
3/8” dia. Bolt should
protrude into track to serve as a roller stop.
21
INSTALLATION
Please Do Not Return This Product To The Store. Contact your local
local yellow pages/business listings or go to the Find a Dealer section online at