Xantrex Technology XHR, XFR, XFR3 manual Models 60-20 100-12 150-8 300-4 600-2

Page 16

Features and Specifications

Specifications

Table 1.2 Specifications for XFR 1200 W Series Supply with GPIB Interface Installed (60 V to 600 V)

Models	60-20	100-12	150-8	300-4	600-2
Program Resolution	9.2mV	15.4mV	23.1mV	46.2mV	92.4mV
Voltage	9.2mV	15.4mV	23.1mV	46.2mV	92.4mV
Current	2.8mA	1.68mA	1.12mA	0.56mA	0.28mA
OVP	9.2mV	15.4mV	23.1mV	46.2mV	92.4mV
Program Accuracy1
Voltage	150mV	150mV	225mV	225mV	250mV
	±0.25%	±0.35%	±0.35%	±0.35%	±0.35%
Current	120mA	80mA	80mA	80mA	50mA
	±0.1%	±0.1%	±0.1%	±0.1%	±0.1%
OVP	600mV	800mV	1.5V	3.0V	6V
Readback Resolution
Voltage	9.2mV	15.4mV	23.1mV	46.2mV	92.4mV
Current	2.8mA	1.68mA	1.12mA	0.56mA	0.28mA
Readback Accuracy1
Voltage	150mV	150mV	225mV	225mV	250mV
	±0.25%	±0.35%	±0.35%	±0.35%	±0.35%
Current	120mA	80mA	80mA	80mA	50mA
	±0.1%	±0.1%	±0.1%	±0.1%	±0.1%

1.Apply accuracy specifications according to the following voltage program accuracy example: Set a model 20-60 power supply to 10 volts.

The expected result will be within the range of 10 volts ± 75mV ± 0.12% of the set voltage of 10 volts.

14	Operating Manual for GPIB for XHR/XFR Series Power Supply

Image 16

Contents GPIB-XHR GPIB-XFR GPIB-XFR3 Page Operating Manual for How do you get service? Phone 604 422 Toll Free North America 800 667 Fax 604 421What does this warranty not cover? Disclaimer Product Information About Your Power Supply Model Number Serial Number Purchased From Purchase DateSafety SupplyMain Sections Manual RevisionsAbout This Manual Contents Contents Features and Specifications DescriptionFeatures and Functions Features and SpecificationsFunctions ReadbackModels 140 12-100 20-60 35-35 40-30 SpecificationsOVP Models 60-20 100-12 150-8 300-4 600-2 Models 300 12-220 20-130 33-85 40-70 Models 60-46 100-28 150-18 300-9 600-4 Models 130 20-50 33-33 40-25 60-18 Models 100-10 150-7 300-3.5 600-1.7 Introduction Initial InspectionInstallation and Configuration Initial InspectionGpib Interface Subplate Located on Power Supply Rear Panel Gpib Interface PCB Step # Description Action Reference Basic Setup ProcedurePON SRQ IEEE-488 Primary Address Selection AddressRear Panel SRQ Switch Position PON SRQ State Power On Service Request PON SRQSwitch Position Power on results Condition Default Settings Model Example IsetIbfind devname IEEE-488 Controller Connection Internal PCB Jumper SelectionsHigh OFF LOW High LOW OFFUser Signals User Signals J7 ConnectorJ7 User Signal Connector Circuit Block Diagram J7 User Cable with Ferrite Block Operation Gpib OperationExample Ascii Bit Decimal Description Reset By Position Weight Request Service SRQ Set whenPower On PON Set when unit LSBComputer Entry Command SyntaxFormat Description Form Floating Number Definition ExampleIset 2.0A Vset Command Summary AUXA? AUXB?CMODE? DLY?FAULT? CmodeIdata IHICommand Reference Command DescriptionAuxa 1 on Auxb 1 onChanging an output setting Response Fold mode where mode is Snsp Mask None = Unmask ALLStatus, and Fault Registers on Accumulated Status, Status, and Fault Registers on SNSP, ALL, NoneResponse Vmax voltage Accumulated Status, Status, and Fault Registers Condition Mnemonic Bit Position Bit WeightError Codes 11 Error CodesTroubleshooting LEDsCalibration Voltage Mode Calibration SetupVoltage Program Calibration Procedure Readback VoltageCalibration Current Calibration Setup Current Mode CalibrationCurrent Program Calibration Procedure Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page Xantrex Technology Inc