Xantrex Technology XHR, XFR, XFR3 Command Reference, Command Description, Auxa 1 on, Auxb 1 on

Page 45

Operation

Command Reference

Command Reference

Table 3.9 Command Reference

Command

Description

ASTS?

Asks for the supply’s accumulated status register. The accumulated status

 

register stores any bit that was entered in the status register since the

 

accumulated status query command (ASTS?) was last used, regardless of

 

whether the condition still exists. The accumulated status register has the

 

same bits, weights, and conditions as the status register. A bit in the

 

accumulated status register will be set at 1 if the corresponding bit in the

 

status register has been 1 (TRUE) at any time since the register was last

 

read. See “Accumulated Status, Status, and Fault Registers” on page 50.

 

The ASTS? query clears the status register.

 

Response: ASTS <status mask> where status mask is the decimal

 

equivalent of the total bit weights for the operating conditions as listed in the

 

status register.

AUXA <1/ON>,<0/OFF>

Controls the AUXA output signal level at rear panel connector J7-7. Active

 

low.

 

Initial value: AUXA 0

AUXA?

Asks for the present set value of the AUXA output signal.

 

Response: AUXA 0 (OFF)

 

AUXA 1 (ON)

AUXB <1/ON>,<0/OFF>

Controls the AUXB output signal level at rear panel connector J7-8. Active

 

low.

 

Initial value: AUXB 0

AUXB?

Asks for the present set value of the AUXB output signal.

 

Response: AUXB 0 (OFF)

 

AUXB 1 (ON)

CLR

Initializes the power supply to its power ON condition. If issued while in local

 

mode, CLR will force power supply settings to register default values as in

 

but these default settings will not come into effect until the power supply is

 

switched to remote mode operation. The CLR commands will clear faults

 

from the fault register. CLR will not reset CMODE.

 

 

CMODE <1/ON>,<0/OFF>

CMODE ON places the power supply into calibration mode for processing

 

calibration commands.

 

Initial value: CMODE OFF or CMODE 0

 

 

CMODE?

Asks for the power supply’s calibration mode status.

 

Response: CMODE 0 (disabled)

 

CMODE 1 (enabled)

 

 

Release 3.1

43

Page 44 Page 46
Image 45
Page 44 Page 46
Contents GPIB-XHR GPIB-XFR GPIB-XFR3 Page Operating Manual for Phone 604 422 Toll Free North America 800 667 Fax 604 421 How do you get service?What does this warranty not cover? Disclaimer Product Model Number Serial Number Purchased From Purchase Date Information About Your Power SupplySupply SafetyManual Revisions Main SectionsAbout This Manual Contents Contents Description Features and SpecificationsFeatures and Specifications Features and FunctionsFunctions ReadbackSpecifications Models 140 12-100 20-60 35-35 40-30OVP Models 60-20 100-12 150-8 300-4 600-2 Models 300 12-220 20-130 33-85 40-70 Models 60-46 100-28 150-18 300-9 600-4 Models 130 20-50 33-33 40-25 60-18 Models 100-10 150-7 300-3.5 600-1.7 Initial Inspection IntroductionInitial Inspection Installation and ConfigurationGpib Interface Subplate Located on Power Supply Rear Panel Gpib Interface PCB Basic Setup Procedure Step # Description Action ReferencePON SRQ Address IEEE-488 Primary Address SelectionPower On Service Request PON SRQ Rear Panel SRQ Switch Position PON SRQ StateSwitch Position Power on results Iset Condition Default Settings Model ExampleIbfind devname Internal PCB Jumper Selections IEEE-488 Controller ConnectionHigh LOW OFF High OFF LOWUser Signals J7 Connector User SignalsJ7 User Signal Connector Circuit Block Diagram J7 User Cable with Ferrite Block Gpib Operation OperationExample Ascii Request Service SRQ Set when Bit Decimal Description Reset By Position WeightPower On PON Set when unit LSBCommand Syntax Computer EntryFormat Floating Number Definition Example Description FormIset 2.0A Vset Command Summary AUXB? AUXA?CMODE? DLY?Cmode FAULT?Idata IHICommand Description Command ReferenceAuxa 1 on Auxb 1 onChanging an output setting Response Fold mode where mode is Mask None = Unmask ALL SnspStatus, and Fault Registers on SNSP, ALL, None Accumulated Status, Status, and Fault Registers onResponse Vmax voltage Condition Mnemonic Bit Position Bit Weight Accumulated Status, Status, and Fault Registers11 Error Codes Error CodesLEDs TroubleshootingCalibration Setup Voltage Mode CalibrationVoltage Program Calibration Procedure Readback VoltageCalibration Current Mode Calibration Current Calibration SetupCurrent Program Calibration Procedure Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page Xantrex Technology Inc
Top Page Image Contents