Xantrex Technology XHR, XFR, XFR3 Auxa?, Auxb?, Cmode?, Dly?, Err?, Fold?, Hold?, Id?, Imax?

Page 43

	Operation
	Command Summary
Table 3.6	Query Commands
Command	Description

AUXA?	Asks for the state of the set value for the AUXA command

AUXB?	Asks for the state of the set value for the AUXB command

CMODE?	Asks for the power supply’s calibration mode status.

DLY?	Asks for the programmable time delay setting before the supply
	reports fault conditions.

ERR?	Asks for the most recent remote programming error which occurred in
	the supply since the last time the error query command (ERR?) was
	used.

FOLD?	Asks for the supply’s present foldback setting.

HOLD?	Asks for the present hold mode setting.

ID?	Asks for the power supply’s model name and master EPROM version.

IMAX?	Asks for the supply’s soft current limit setting.

IOUT?	Measures the supply’s actual current output.

ISET?	Asks for the supply’s present output current limit setting.

OUT?	Asks for the present enabled/disabled status of the supply’s output.

OVSET?	Asks for the supply’s present over voltage protection limit.

ROM?	Asks for the version number of the master and slave EPROMs on the
	interface PCB.
SRQ?	Asks for the present enabled/disabled status of the IEEE-488 Service
	Requests generated by the supply.

VMAX?	Asks for the supply’s soft voltage limit setting.

VOUT?	Measures the supply’s actual voltage output.

VSET?	Asks for the supply’s present output voltage setting.

Release 3.1

41

Image 43

Contents GPIB-XHR GPIB-XFR GPIB-XFR3 Page Operating Manual for Phone 604 422 Toll Free North America 800 667 Fax 604 421 How do you get service?What does this warranty not cover? Disclaimer Product Model Number Serial Number Purchased From Purchase Date Information About Your Power SupplySupply SafetyManual Revisions Main SectionsAbout This Manual Contents Contents Description Features and SpecificationsReadback Features and FunctionsFeatures and Specifications FunctionsModels 140 12-100 20-60 35-35 40-30 SpecificationsOVP Models 60-20 100-12 150-8 300-4 600-2 Models 300 12-220 20-130 33-85 40-70 Models 60-46 100-28 150-18 300-9 600-4 Models 130 20-50 33-33 40-25 60-18 Models 100-10 150-7 300-3.5 600-1.7 Initial Inspection IntroductionInitial Inspection Installation and ConfigurationGpib Interface Subplate Located on Power Supply Rear Panel Gpib Interface PCB Step # Description Action Reference Basic Setup ProcedurePON SRQ Address IEEE-488 Primary Address SelectionRear Panel SRQ Switch Position PON SRQ State Power On Service Request PON SRQSwitch Position Power on results Iset Condition Default Settings Model ExampleIbfind devname Internal PCB Jumper Selections IEEE-488 Controller ConnectionHigh LOW OFF High OFF LOWUser Signals J7 Connector User SignalsJ7 User Signal Connector Circuit Block Diagram J7 User Cable with Ferrite Block Gpib Operation OperationExample Ascii LSB Bit Decimal Description Reset By Position WeightRequest Service SRQ Set when Power On PON Set when unitComputer Entry Command SyntaxFormat Floating Number Definition Example Description FormIset 2.0A Vset Command Summary DLY? AUXA?AUXB? CMODE?IHI FAULT?Cmode IdataAuxb 1 on Command ReferenceCommand Description Auxa 1 onChanging an output setting Response Fold mode where mode is Mask None = Unmask ALL SnspStatus, and Fault Registers on SNSP, ALL, None Accumulated Status, Status, and Fault Registers onResponse Vmax voltage Condition Mnemonic Bit Position Bit Weight Accumulated Status, Status, and Fault Registers11 Error Codes Error CodesLEDs TroubleshootingCalibration Voltage Voltage Mode CalibrationSetup Voltage Program Calibration Procedure ReadbackCalibration Current Calibration Setup Current Mode CalibrationCurrent Program Calibration Procedure Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page Xantrex Technology Inc