Xantrex Technology XHR, XFR, XFR3 manual Installation and Configuration, Initial Inspection

Page 22

Installation and Configuration

Initial Inspection

CAUTION

Use proper static control techniques to avoid damage to static-sensitive components on the printed circuit board.

Remote LED (REM)

Local Switch (LOCAL)

Remote Programming LEDs:

Address LED (ADR)

Indicates that the master controller is addressing the unit.

Service Request LED (SRQ)

Comes on at power up if the PON SRQ switch is set to on. You can enable the SRQ LED during normal operation with the SRQ command.

Error LED (ERR)

Indicates when a programming error has occurred. You can clear the ERR LED with an error query command.

Fault LED (FLT)

Indicates that a fault has occurred. The fault bit must be unmasked. Refer to the status register in Table 3.10, on page 50. Momentarily lights if PON SRQ is set to on.

Polarity LED (POL)

Indicates that the polarity user line has been

activated. See “Connector J7 User Signals” on page 30.

Figure 2.1Power Supply Front Panel with GPIB Interface Installed (1200 Watt Power Supply Shown)

20	Operating Manual for GPIB for XHR/XFR Series Power Supply

Image 22

Contents GPIB-XHR GPIB-XFR GPIB-XFR3 Page Operating Manual for How do you get service? Phone 604 422 Toll Free North America 800 667 Fax 604 421What does this warranty not cover? Disclaimer Product Information About Your Power Supply Model Number Serial Number Purchased From Purchase DateSafety SupplyMain Sections Manual RevisionsAbout This Manual Contents Contents Features and Specifications DescriptionFunctions Features and FunctionsFeatures and Specifications ReadbackModels 140 12-100 20-60 35-35 40-30 SpecificationsOVP Models 60-20 100-12 150-8 300-4 600-2 Models 300 12-220 20-130 33-85 40-70 Models 60-46 100-28 150-18 300-9 600-4 Models 130 20-50 33-33 40-25 60-18 Models 100-10 150-7 300-3.5 600-1.7 Introduction Initial InspectionInstallation and Configuration Initial InspectionGpib Interface Subplate Located on Power Supply Rear Panel Gpib Interface PCB Step # Description Action Reference Basic Setup ProcedurePON SRQ IEEE-488 Primary Address Selection AddressRear Panel SRQ Switch Position PON SRQ State Power On Service Request PON SRQSwitch Position Power on results Condition Default Settings Model Example IsetIbfind devname IEEE-488 Controller Connection Internal PCB Jumper SelectionsHigh OFF LOW High LOW OFFUser Signals User Signals J7 ConnectorJ7 User Signal Connector Circuit Block Diagram J7 User Cable with Ferrite Block Operation Gpib OperationExample Ascii Power On PON Set when unit Bit Decimal Description Reset By Position WeightRequest Service SRQ Set when LSBComputer Entry Command SyntaxFormat Description Form Floating Number Definition ExampleIset 2.0A Vset Command Summary CMODE? AUXA?AUXB? DLY?Idata FAULT?Cmode IHIAuxa 1 on Command ReferenceCommand Description Auxb 1 onChanging an output setting Response Fold mode where mode is Snsp Mask None = Unmask ALLStatus, and Fault Registers on Accumulated Status, Status, and Fault Registers on SNSP, ALL, NoneResponse Vmax voltage Accumulated Status, Status, and Fault Registers Condition Mnemonic Bit Position Bit WeightError Codes 11 Error CodesTroubleshooting LEDsCalibration Voltage Program Calibration Procedure Readback Voltage Mode CalibrationSetup VoltageCalibration Current Calibration Setup Current Mode CalibrationCurrent Program Calibration Procedure Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page Xantrex Technology Inc