Xantrex Technology XHR, XFR, XFR3 Cmode, Idata, Ihi, Ilo, Irdat, Irhi, Irlo, Ovcal, Vdata, Vhi

Page 44

Operation

Command Summary

Table 3.7	Calibration Commands
Command	Description

CMODE	Places the supply into calibration mode.

IDATA	Calculates the slope and intercept for current programming.

IHI	Sets the current output to the high calibration point.

ILO	Sets the current output to the low calibration point.

IRDAT	Calculates the slope and intercept for current readback.

IRHI	Sets the current output to the high readback point.

IRLO	Sets the current output to the low readback point.

OVCAL	Calibrates the over voltage protection (OVP).

VDATA	Calculates the slope and intercept for voltage programming.

VHI	Sets the voltage output to the high calibration point.

VLO	Sets the voltage output to the low calibration point.

VRDAT	Calculates the slope and intercept for voltage readback.

VRHI	Sets the voltage output to the high readback point.

VRLO	Sets the voltage output to the low readback point.

Table 3.8	Status Commands
Command	Description

ASTS?	Asks for the supply’s accumulated status register.

FAULT?	Asks for the supply’s fault register for the status preset operating
	conditions.
MASK	Prevents the supply's previously unmasked operating conditions from
	setting bits in the fault register.

STS?	Asks for the supply’s present status register.

UNMASK	Enables you to select those supply's operating conditions that you are
	most interested in monitoring for fault occurrence.

UNMASK?	Asks for the supply's fault conditions which are currently enabled
	(unmasked).

42	Operating Manual for GPIB for XHR/XFR Series Power Supply

Image 44

Contents GPIB-XHR GPIB-XFR GPIB-XFR3 Page Operating Manual for How do you get service? Phone 604 422 Toll Free North America 800 667 Fax 604 421What does this warranty not cover? Disclaimer Product Information About Your Power Supply Model Number Serial Number Purchased From Purchase DateSafety SupplyMain Sections Manual RevisionsAbout This Manual Contents Contents Features and Specifications DescriptionFeatures and Functions Features and SpecificationsFunctions ReadbackOVP SpecificationsModels 140 12-100 20-60 35-35 40-30 Models 60-20 100-12 150-8 300-4 600-2 Models 300 12-220 20-130 33-85 40-70 Models 60-46 100-28 150-18 300-9 600-4 Models 130 20-50 33-33 40-25 60-18 Models 100-10 150-7 300-3.5 600-1.7 Introduction Initial InspectionInstallation and Configuration Initial InspectionGpib Interface Subplate Located on Power Supply Rear Panel Gpib Interface PCB PON SRQ Basic Setup ProcedureStep # Description Action Reference IEEE-488 Primary Address Selection AddressSwitch Position Power on results Power On Service Request PON SRQRear Panel SRQ Switch Position PON SRQ State Condition Default Settings Model Example IsetIbfind devname IEEE-488 Controller Connection Internal PCB Jumper SelectionsHigh OFF LOW High LOW OFFUser Signals User Signals J7 ConnectorJ7 User Signal Connector Circuit Block Diagram J7 User Cable with Ferrite Block Operation Gpib OperationExample Ascii Bit Decimal Description Reset By Position Weight Request Service SRQ Set whenPower On PON Set when unit LSBFormat Command SyntaxComputer Entry Description Form Floating Number Definition ExampleIset 2.0A Vset Command Summary AUXA? AUXB?CMODE? DLY?FAULT? CmodeIdata IHICommand Reference Command DescriptionAuxa 1 on Auxb 1 onChanging an output setting Response Fold mode where mode is Snsp Mask None = Unmask ALLStatus, and Fault Registers on Accumulated Status, Status, and Fault Registers on SNSP, ALL, NoneResponse Vmax voltage Accumulated Status, Status, and Fault Registers Condition Mnemonic Bit Position Bit WeightError Codes 11 Error CodesTroubleshooting LEDsCalibration Voltage Mode Calibration SetupVoltage Program Calibration Procedure Readback VoltageCalibration Current Program Calibration Procedure Current Mode CalibrationCurrent Calibration Setup Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page Xantrex Technology Inc