Xantrex Technology XHR, XFR, XFR3 manual Safety, Supply

Page 8

Power

Supply		WARNING—High Energy and High Voltage
Safety		Exercise caution when using and calibrating a power supply. High energy levels
		can be stored at the output voltage terminals on a power supply in normal
		operation. In addition, potentially lethal voltages exist in the power circuit and on
		the output and sense connectors of a power supply with a rated output greater
		than 40 V. Filter capacitors store potentially dangerous energy for some time after
		power is removed.


		CAUTION
		CAUTION
		Operate the power supply in an environment free of flammable gases or fumes.
		To ensure that the power supply’s safety features are not compromised, use the
		power supply as specified in this manual and do not substitute parts or make any
		unauthorized modifications. Contact the service technician for service and repair
		help. Repairs must be made by experienced service technicians only.

Warnings,

Cautions,

and Notes

Warnings, cautions, and notes are defined and formatted in this manual as shown below.

WARNING

Describes a potential hazard which could result in injury or death, or, a procedure which, if not performed correctly, could result in injury or death.

CAUTION

Describes a procedure which, if not performed correctly, could result in damage to data, equipment, or systems.

Note

Describes additional operating information which may affect the performance of the equipment.

vi	Operating Manual for GPIB for XHR/XFR Series Power Supply

Image 8

Contents GPIB-XHR GPIB-XFR GPIB-XFR3 Page Operating Manual for How do you get service? Phone 604 422 Toll Free North America 800 667 Fax 604 421What does this warranty not cover? Disclaimer Product Information About Your Power Supply Model Number Serial Number Purchased From Purchase DateSafety SupplyMain Sections Manual RevisionsAbout This Manual Contents Contents Features and Specifications DescriptionFeatures and Functions Features and SpecificationsFunctions ReadbackOVP SpecificationsModels 140 12-100 20-60 35-35 40-30 Models 60-20 100-12 150-8 300-4 600-2 Models 300 12-220 20-130 33-85 40-70 Models 60-46 100-28 150-18 300-9 600-4 Models 130 20-50 33-33 40-25 60-18 Models 100-10 150-7 300-3.5 600-1.7 Introduction Initial InspectionInstallation and Configuration Initial InspectionGpib Interface Subplate Located on Power Supply Rear Panel Gpib Interface PCB PON SRQ Basic Setup ProcedureStep # Description Action Reference IEEE-488 Primary Address Selection AddressSwitch Position Power on results Power On Service Request PON SRQRear Panel SRQ Switch Position PON SRQ State Condition Default Settings Model Example IsetIbfind devname IEEE-488 Controller Connection Internal PCB Jumper SelectionsHigh OFF LOW High LOW OFFUser Signals User Signals J7 ConnectorJ7 User Signal Connector Circuit Block Diagram J7 User Cable with Ferrite Block Operation Gpib OperationExample Ascii Bit Decimal Description Reset By Position Weight Request Service SRQ Set whenPower On PON Set when unit LSBFormat Command SyntaxComputer Entry Description Form Floating Number Definition ExampleIset 2.0A Vset Command Summary AUXA? AUXB?CMODE? DLY?FAULT? CmodeIdata IHICommand Reference Command DescriptionAuxa 1 on Auxb 1 onChanging an output setting Response Fold mode where mode is Snsp Mask None = Unmask ALLStatus, and Fault Registers on Accumulated Status, Status, and Fault Registers on SNSP, ALL, NoneResponse Vmax voltage Accumulated Status, Status, and Fault Registers Condition Mnemonic Bit Position Bit WeightError Codes 11 Error CodesTroubleshooting LEDsCalibration Voltage Mode Calibration SetupVoltage Program Calibration Procedure Readback VoltageCalibration Current Program Calibration Procedure Current Mode CalibrationCurrent Calibration Setup Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page Xantrex Technology Inc