Shindaiwa T3410/EVC, 89301 Stopping the Engine, Adjusting Engine Idle, Checking Unit Condition

Page 12

Starting the Engine (continued)

Starting A Flooded Engine

1.Disconnect the spark plug lead and use the spark plug wrench to remove the spark plug (turn counter clockwise to remove).

2.Slide the ignition switch to the “O” (STOP) position.

ŶIf the spark plug is fouled or soaked with fuel, clean the plug as necessary.

3.Open the choke and fully depress the throttle lever with your left hand, then pull the starter handle rapidly with your right hand to clear excess fuel from the combustion chamber.

4.Replace the spark plug and tighten it firmly with the spark plug wrench. If a torque wrench is available, torque the spark plug to the values recommended in the “Specifications” section.

5.Repeat the starting procedure for a warm engine.

6.If the engine still fails to start, refer to the troubleshooting section near the end of this manual.

Stopping the Engine

Idle the engine briefly before stopping (about 2 minutes), then slide the ignition

switch to the “O” (Engine OFF) position.

OFF

Slide ignition to OFF

Adjusting Engine Idle

The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment.

WARNING!

The cutting attachment must NEVER rotate at engine idle! If the idle speed cannot be adjusted by the procedure described here, return the unit to your Shindaiwa dealer for inspection.

Checking Unit Condition

Idle Speed Adjustment

1.Place the unit on the ground, then start the engine, and then allow it to idle 2-3 minutes until warm.

2.If the attachment rotates when the engine is at idle, reduce the idle speed by turning the idle adjustment screw counter-clockwise.

3.If a tachometer is available, adjust idle. Check Specifications page for correct idle speed

NOTE

Carburetor fuel mixture adjustments are preset at factory and cannot be serviced LQWKH¿HOG

Idle Adjusting

Screw

NEVER operate the unit with the cut- ting attachment shield or other protec- tive devices removed!

Use only authorized Shindaiwa parts and accessories with your Shindaiwa trimmer. Do not make modifications to this unit with- out written approval from Shindaiwa, Inc.

ALWAYS make sure the cutting attach- ment is properly installed and firmly tightened before operation.

NEVER use a cracked or warped cutting attachment: replace it with a serviceable one.

ALWAYS make sure the cutting attach- ment fits properly into the appropriate attachment holder. If a properly installed attachment vibrates, replace the attach- ment with new one and re-check.

ALWAYS stop the engine immediately and check for damage if you strike a foreign object or if the unit becomes tangled. Do not operate with broken or damaged equipment.

NEVER allow the engine to run at high RPM without a load. Doing so could dam- age the engine.

NEVER operate a unit with worn or dam- aged fasteners or attachment holders.

WARNING!

A cutting attachment shield or other protective device is no guarantee of protection against ricochet. YOU MUST ALWAYS GUARD AGAINST FLYING DEBRIS!

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents T3410/EVC Trimmer T3410X/EVC Trimmer Contents IntroductionSafety Safety LabelsWork Safely Stay AlertProperly Equipped Operator Be Aware of the Working EnvironmentProduct Description Outer Tube Gearcase Cutting Attachment Shield Trimmer HeadAssembly Prior to AssemblyEngine and shaft assembly Cutting attachment shield Handle and barrier bar X unitSub-Shield When trimmer head is in use Cutting Attachment Shield T, TX unitAdjust throttle lever free play Install trimmer head Installing Brushcutter Blade Remove the hex wrenchMixing fuel Filling the fuel tankExamples of 501 mixing quantities Minimize the Risk of FireWhen the Engine Starts Starting the EngineDepress and hold the throttle lock button Adjusting Engine Idle Idle Speed AdjustmentStopping the Engine Checking Unit ConditionOperation Using a Blade Blade ThrustBrushcutter Handlebar Brushcutter harnessMaintenance Hour maintenance 10/15-Hour maintenanceRemove and clean or replace the spark plug Gearcase lubrication139/150-Hour Maintenance Valve AdjustmentMaintenance after first 139-hours Remove and replace the fuel filter ElementLong Term Storage 0XIÁHUDQGVSDUNDUUHVWHU DlqwhqdqfhBlade Sharpening Shindaiwa Tornado BladeMultiple-tooth Circular Blade Troubleshooting Guide Engine does not StartWhat To Check RemedyLOW Power Possible CauseIs the engine overheating? Engine is knockingAdditional Problems What To Check Possible Cause RemedyEmission System Warranty Statement NOTAs RemarquesPodadora T3410 Podadora T3410X Introducción ContenidoDeclaraciones De Seguridad Etiquetas de seguridadSeguridad Trabaje con cuidadoMantengase Alerta Etiquetas de seguridadSeguridad continuación El operario debidamente equipadoSP4 Descripción del Producto VshflàfdflrqhvEnsamblaje Antes de EnsamblarMango y barra protectora unidades TX Protector Secundario cuando el Protector del accesorio de corteSP7 Ensamblaje continuacion Ajuste la holgura del aceleradorInstalación del cabezal de corte Retire la llave hexagonalInstalación de la cuchilla desmalezadora Mezcla de Combustible Llenando el Tanque de CombustibleEjemplos de cantidades de mezcla a proporción de Disminuya el riesgo de incendiosArranque del motor Al arrancar el motorDeslice el interruptor de ignición a la Posición O motor ApagadoOperación Correa de HombroCorte de Césped Máquinas Equipadas con Cabezal de Corte BordesOperación continuación Mantenimiento Mantenimiento continuación Mantenimiento cada 10 horasMantenimiento cada 50 horas Más frecuentemente en condiciones rigurosasMantenimiento Cada 139/150 Horas Ajuste de válvulasRetire y reemplace el elemento del filtro Un ajuste incorrecto de las válvuMantenimiento de la silenciador Almacenamiento de Largo PlazoRetire la malla y limpie con un cepillo de cerdas gruesas Repita los pasos 1 y 2 hasta que el motor ya no arranqueDisco Shindaiwa Tornado Discos de dientes múltiplesGuía Diagnóstico EL Motor no ArrancaQué revisar Posible causaBaja Potencia ¿Se sobrecalienta el motor?Limpiar, reparar o sustituir en caso necesario El motor golpeaGuía Diagnóstico continuación Esta garantía es administrada por Sus Derechos y Obligaciones de GarantíaCobertura de la Garantía del Fabricante Que Está Cubierto Por Esta GarantíaTualatin, Oregon 97062 USA 11, Ozuka-Nishi COUPE-BORDURE T3410/EVC T3410X/EVC Table des matières Mises en gardeSécurité Sécurité au travailDemeurer alerte Étiquettes de sécuritéSécurité suite Équipement complet de l’utilisateurNomenclature Caractéristiques techniquesAssemblage Avant l’assemblagePoignée y Barre de sécurité X appareil FR6Assemblage suite PÁHFWHXUPÁHFWHXULQIpULHXUlorsque la tête FR7Installer la tête de coupe Réglage du jeu du levier d’accélérationRetirer la clé hexagonale du boîtier ’engrenage et des supportsInstallation de la lame de débroussailleuse Mélange de carburant Remplissage du réservoir à carburantExemples de quantités de mélange de carburant à Réduire les risques d’incendieDémarrage du moteur Lorsque le moteur démarreDémarrage du moteur suite Arrêt du moteurRéglage du ralenti du moteur Contrôle de l’état de l’appareilFonctionnement Fonctionnement suite Entretien Entretien suite Entretien aux 10 heuresEntretien aux 10 à 15 heures Entretien aux 50 heuresRemplacement du filtre à carburant Entretien toutes les 50 heures suiteEntretien aux 139 heures Réglage du jeu des soupapesRemisage à long terme Entretien du silencieuxAffûtage de la lame Lame Shindaiwa TornadoLame circulaire à plusieurs dents Solution Guide de dépannageLE Moteur NE Démarre PAS Points à contrôlerGuide de dépannage suite Puissance InsuffisanteLe moteur surchauffe-t-il ? Le moteur cognePoints à contrôler Cause probable Solution Autres ProblèmesLa présente garantie est administrée par Vos droits et obligations en vertu de la garantieCouverture de la garantie des fabricants Couverture de la garantie
Top Page Image Contents