Shindaiwa 89301, T3410/EVC, T3410X/EVC manual Adjust throttle lever free play, Install trimmer head

Page 8

Assembly (continued)

Adjust throttle lever free play

The throttle lever free play should be approximately 4 - 6 mm (3/16” - 1/4”). Make sure that the throttle lever oper- ates smoothly without binding. If it becomes necessary to adjust the lever free play, follow the procedures and illus- trations that follow.

1.Loosen the air cleaner cover knob(s) and remove the air cleaner cover.

2.Loosen the lock nut on the cable adjuster. Turn the cable adjuster in or out as required to obtain proper free play 4 - 6 mm.

3.Tighten the locknut.

4.Reinstall the air cleaner cover.

4-6 mm

(3/16”-1/4”)

Throttle Free Play

Throttle lever free play

Cable

Adjuster

Lock Nut

Adjust as required for 4-6 mm free play

Remove air cleaner cover

Install trimmer head

WARNING!

A standard grass trimmer with a loop handle should NEVER be operated with blade-type attach- ments. For blade use, the trimmer PXVWEH¿WWHGZLWKDELF\FOHW\SHKDQ- dlebar or a barrier bar that is located in front of the operator to reduce the risk of the operator from coming in contact with the cutting attachment (per ANSI B175.3). When using a blade, the unit must also be equipped with a harness or strap.

NOTE:

This unit is shipped with Holder A, the blade retainer (safety clip), Holder B, shaft bolt, and bolt guard installed. The shaft bolt is a LEFT-HAND thread. Remove it by turning CLOCKWISE!

IMPORTANT

To install a trimmer head onto a TX unit, first remove the shaft bolt and bolt guard.

1.Position the gearcase with the output shaft facing up and remove both holders.

2.Position Holder A as shown and slide it onto the gearcase shaft.

3.Install and center the safety clip on the gearcase shaft.

Install Holder

A

Position the gearcase with the output shaft facing up

4.Install Holder B on the gearcase shaft. The machined boss on Holder A must engage with the recess on Holder B.

5.Rotate the gearshaft and holders until the hole in Holder A aligns with the matching hole in the gearcase flange, and then lock the holder to the gearcase by inserting the long end of the hex wrench through both holes.

6.Using a counter-clockwise rotation and hand pressure alone, thread and securely tighten the trimmer head into the gearcase shaft.

7.Remove the hex wrench from the gearcase and holders.

8.Adjust the trimmer line length to reach no further than the line cutter on the cutting attachment shield. Trim to the correct length if necessary.

Install Holder

B

Safety Clip

Install and center the safety clip

Hand-tighten trimmer head

Hex Wrench

Securely tighten the trimmer head into the gearcase shaft

The unit should now be

completely assembled and ready

for use with a trimmer head.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents T3410/EVC Trimmer T3410X/EVC Trimmer Contents IntroductionSafety Safety LabelsWork Safely Stay AlertProperly Equipped Operator Be Aware of the Working EnvironmentProduct Description Outer Tube Gearcase Cutting Attachment Shield Trimmer HeadAssembly Prior to AssemblyEngine and shaft assembly Cutting attachment shield Handle and barrier bar X unitSub-Shield When trimmer head is in use Cutting Attachment Shield T, TX unitAdjust throttle lever free play Install trimmer headInstalling Brushcutter Blade Remove the hex wrenchMixing fuel Filling the fuel tankExamples of 501 mixing quantities Minimize the Risk of FireDepress and hold the throttle lock button When the Engine StartsStarting the Engine Adjusting Engine Idle Idle Speed AdjustmentStopping the Engine Checking Unit ConditionOperation Using a Blade Blade ThrustBrushcutter Handlebar Brushcutter harnessMaintenance Hour maintenance 10/15-Hour maintenanceRemove and clean or replace the spark plug Gearcase lubrication139/150-Hour Maintenance Valve AdjustmentMaintenance after first 139-hours Remove and replace the fuel filter ElementLong Term Storage 0XIÁHUDQGVSDUNDUUHVWHU DlqwhqdqfhMultiple-tooth Circular Blade Blade SharpeningShindaiwa Tornado Blade Troubleshooting Guide Engine does not StartWhat To Check RemedyLOW Power Possible CauseIs the engine overheating? Engine is knockingAdditional Problems What To Check Possible Cause RemedyEmission System Warranty Statement NOTAs RemarquesPodadora T3410 Podadora T3410X Introducción ContenidoDeclaraciones De Seguridad Etiquetas de seguridadSeguridad Trabaje con cuidadoMantengase Alerta Etiquetas de seguridadSP4 Seguridad continuaciónEl operario debidamente equipado Descripción del Producto VshflàfdflrqhvMango y barra protectora unidades TX EnsamblajeAntes de Ensamblar SP7 Protector Secundario cuando elProtector del accesorio de corte Ensamblaje continuacion Ajuste la holgura del aceleradorInstalación del cabezal de corte Retire la llave hexagonalInstalación de la cuchilla desmalezadora Mezcla de Combustible Llenando el Tanque de CombustibleEjemplos de cantidades de mezcla a proporción de Disminuya el riesgo de incendiosArranque del motor Al arrancar el motorDeslice el interruptor de ignición a la Posición O motor ApagadoOperación Correa de HombroCorte de Césped Máquinas Equipadas con Cabezal de Corte BordesOperación continuación Mantenimiento Mantenimiento continuación Mantenimiento cada 10 horasMantenimiento cada 50 horas Más frecuentemente en condiciones rigurosasMantenimiento Cada 139/150 Horas Ajuste de válvulasRetire y reemplace el elemento del filtro Un ajuste incorrecto de las válvuMantenimiento de la silenciador Almacenamiento de Largo PlazoRetire la malla y limpie con un cepillo de cerdas gruesas Repita los pasos 1 y 2 hasta que el motor ya no arranqueDisco Shindaiwa Tornado Discos de dientes múltiplesGuía Diagnóstico EL Motor no ArrancaQué revisar Posible causaBaja Potencia ¿Se sobrecalienta el motor?Limpiar, reparar o sustituir en caso necesario El motor golpeaGuía Diagnóstico continuación Esta garantía es administrada por Sus Derechos y Obligaciones de GarantíaCobertura de la Garantía del Fabricante Que Está Cubierto Por Esta GarantíaTualatin, Oregon 97062 USA 11, Ozuka-Nishi COUPE-BORDURE T3410/EVC T3410X/EVC Table des matières Mises en gardeSécurité Sécurité au travailDemeurer alerte Étiquettes de sécuritéSécurité suite Équipement complet de l’utilisateurNomenclature Caractéristiques techniquesAssemblage Avant l’assemblagePoignée y Barre de sécurité X appareil FR6Assemblage suite PÁHFWHXUPÁHFWHXULQIpULHXUlorsque la tête FR7Installer la tête de coupe Réglage du jeu du levier d’accélérationRetirer la clé hexagonale du boîtier ’engrenage et des supportsInstallation de la lame de débroussailleuse Mélange de carburant Remplissage du réservoir à carburantExemples de quantités de mélange de carburant à Réduire les risques d’incendieDémarrage du moteur Lorsque le moteur démarreDémarrage du moteur suite Arrêt du moteurRéglage du ralenti du moteur Contrôle de l’état de l’appareilFonctionnement Fonctionnement suite Entretien Entretien suite Entretien aux 10 heuresEntretien aux 10 à 15 heures Entretien aux 50 heuresRemplacement du filtre à carburant Entretien toutes les 50 heures suiteEntretien aux 139 heures Réglage du jeu des soupapesRemisage à long terme Entretien du silencieuxLame circulaire à plusieurs dents Affûtage de la lameLame Shindaiwa Tornado Solution Guide de dépannageLE Moteur NE Démarre PAS Points à contrôlerGuide de dépannage suite Puissance InsuffisanteLe moteur surchauffe-t-il ? Le moteur cognePoints à contrôler Cause probable Solution Autres ProblèmesLa présente garantie est administrée par Vos droits et obligations en vertu de la garantieCouverture de la garantie des fabricants Couverture de la garantie

T3410X/EVC, T3410/EVC, 89301 specifications

Shindaiwa is renowned for its durable and high-performing outdoor power equipment, and models like the Shindaiwa 89301, T3410/EVC, and T3410X/EVC highlight this reputation. These models are designed for both commercial and residential use, featuring advanced technologies that enhance performance and user experience.

The Shindaiwa 89301 is a versatile and powerful equipment that excels in various landscaping tasks. Its most notable feature is its robust engine, which provides exceptional power while maintaining fuel efficiency. This model incorporates Shindaiwa's advanced Clean Air Technology, which significantly reduces emissions, making it environmentally friendly and compliant with stringent regulations. The ergonomic design of the handle ensures comfort during prolonged use, reducing operator fatigue.

Moving on to the T3410/EVC, this model is primarily a brushcutter, known for its reliability and ease of use. It is equipped with a high-quality cutting system that delivers precise cuts and efficient grass clearing. The T3410/EVC features a powerful engine that provides strong torque at low RPMs, allowing for effective cutting through thick grass and weeds. One of the standout technologies in this unit is the E-Vac system, which enhances airflow in the cutting head for improved debris discharge. This ensures a clean and efficient cut, reducing the time spent on yard work.

Meanwhile, the T3410X/EVC model pushes the boundaries even further with additional capabilities. It features a more advanced ignition system that offers quicker starts and better overall performance in challenging conditions. This model also boasts a reinforced frame and components designed for demanding tasks, making it ideal for professionals who require reliability and performance. Just like the T3410/EVC, the T3410X/EVC is integrated with an advanced vibration dampening system, enhancing user comfort and control during operations.

Both models' user-friendly controls and lightweight design make them accessible for both seasoned professionals and casual users. Whether you are tackling a large commercial property or maintaining your backyard, Shindaiwa’s models 89301, T3410/EVC, and T3410X/EVC deliver exceptional performance, durability, and innovation, ensuring that your outdoor projects are completed efficiently and effectively. With a combination of power, technology, and ergonomic design, these models stand out in the competitive landscape of outdoor power equipment.
Top Page Image Contents