Shindaiwa T3410/EVC, T3410X/EVC, 89301 manual Maintenance

Page 15

Maintenance

General maintenancel

IMPORTANT!

MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PER- FORMED BY ANY REPAIR ESTABLISH- MENT OR INDIVIDUAL; HOWEVER, WAR- RANTY REPAIRS MUST BE PERFORMED BY A DEALER OR SERVICE CENTER AUTHORIZED BY SHINDAIWA INC. THE USE OF PARTS THAT ARE NOT EQUIVA- LENT IN PERFORMANCE AND DURA- BILITY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A BEARING ON THE OUTCOME OF A WARRANTY CLAIM.

NOTE:

Using non-standard replacement parts could invalidate your Shindaiwa warranty.

WARNING!

Before performing any mainte- nance, repair, or cleaning work on the unit, make sure the engine and cutting attachment are completely stopped.

Disconnect the spark plug wire before performing service or maintenance.

0XIÁHU

This unit must never be operated with a faulty or missing spark arrester or muf- fler. Make sure the muffler is well secured and in good condition. A worn or damaged muffler is a fire hazard and may also cause hearing loss.

Spark Plug

Keep the spark plug and wire connections tight and clean.

Fasteners

Make sure nuts, bolts, and screws (except carburetor adjusting screws) are tight.

WARNING!

Non-standard accessories, cut- ting attachment, or replacement parts may not operate properly with your unit and may cause damage and lead to personal injury.

Air Filter

The C4 engine that powers your Shindaiwa model is a hybrid 4-stroke engine. As a hybrid, the engine is lubricated by oil mixed with the gasoline and air from the carburetor that moves through and around the internal parts of the engine in a similar way that a

2-stroke engine is lubricated. Without the heavy duty 2-stage air filter equipped on all C4 engines, dust and dirt could also move through the engine, decreasing engine life, increasing valve wear and the need for more frequent valve adjustments. To keep your C4 engine strong and reliable, Shindaiwa recommends that you check and service the air filter as instructed in the 10-Hour Mainte- nance section that follows.

Daily maintenance

Prior to each work day, perform the following:

ŶRemove all dirt and debris from the engine, check the cooling fins and air cleaner for clogging, and clean as necessary.

ŶCarefully remove any accumulations of dirt or debris from the muffler and fuel tank. Check cooling air intake area at base of crankcase. Remove all debris. Dirt build-up in these areas can lead to engine overheating, fire, or premature wear.

WARNING!

Always wear gloves when working around the cutter assembly.

ŶLubricate the blades before use and after refueling. Check the cutters for damage or incorrect adjustment.

ŶClean any debris or dirt from the cut- ting attachment.

Cooling

¿QV

Cooling

¿QV

Air

intake

5HPRYHDOOGLUWDQGGHEULVIURPWKHHQJLQHDQGFKHFNWKHFRROLQJ¿QV

Ŷ Check for loose or missing screws or

Ŷ Make sure nuts, bolts, and screws

components. Make sure the cutter

(except carburetor idle speed adjusting

attachment is securely fastened.

screws) are tight.

Ŷ Check the entire unit for leaking fuel

 

or grease.

 

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents T3410/EVC Trimmer T3410X/EVC Trimmer Introduction ContentsStay Alert SafetySafety Labels Work SafelyBe Aware of the Working Environment Properly Equipped OperatorOuter Tube Gearcase Cutting Attachment Shield Trimmer Head Product DescriptionHandle and barrier bar X unit AssemblyPrior to Assembly Engine and shaft assembly Cutting attachment shieldCutting Attachment Shield T, TX unit Sub-Shield When trimmer head is in useInstall trimmer head Adjust throttle lever free playRemove the hex wrench Installing Brushcutter BladeMinimize the Risk of Fire Mixing fuelFilling the fuel tank Examples of 501 mixing quantitiesWhen the Engine Starts Starting the EngineDepress and hold the throttle lock button Checking Unit Condition Adjusting Engine IdleIdle Speed Adjustment Stopping the EngineOperation Brushcutter harness Using a BladeBlade Thrust Brushcutter HandlebarMaintenance Gearcase lubrication Hour maintenance10/15-Hour maintenance Remove and clean or replace the spark plugRemove and replace the fuel filter Element 139/150-Hour MaintenanceValve Adjustment Maintenance after first 139-hours0XIÁHUDQGVSDUNDUUHVWHU Dlqwhqdqfh Long Term StorageBlade Sharpening Shindaiwa Tornado BladeMultiple-tooth Circular Blade Remedy Troubleshooting GuideEngine does not Start What To CheckEngine is knocking LOW PowerPossible Cause Is the engine overheating?What To Check Possible Cause Remedy Additional ProblemsEmission System Warranty Statement Remarques NOTAsPodadora T3410 Podadora T3410X Etiquetas de seguridad IntroducciónContenido Declaraciones De SeguridadEtiquetas de seguridad SeguridadTrabaje con cuidado Mantengase AlertaSeguridad continuación El operario debidamente equipadoSP4 Vshflàfdflrqhv Descripción del ProductoEnsamblaje Antes de EnsamblarMango y barra protectora unidades TX Protector Secundario cuando el Protector del accesorio de corteSP7 Retire la llave hexagonal Ensamblaje continuacionAjuste la holgura del acelerador Instalación del cabezal de corteInstalación de la cuchilla desmalezadora Disminuya el riesgo de incendios Mezcla de CombustibleLlenando el Tanque de Combustible Ejemplos de cantidades de mezcla a proporción deAl arrancar el motor Arranque del motorPosición O motor Apagado Deslice el interruptor de ignición a laBordes OperaciónCorrea de Hombro Corte de Césped Máquinas Equipadas con Cabezal de CorteOperación continuación Mantenimiento Más frecuentemente en condiciones rigurosas Mantenimiento continuaciónMantenimiento cada 10 horas Mantenimiento cada 50 horasUn ajuste incorrecto de las válvu Mantenimiento Cada 139/150 HorasAjuste de válvulas Retire y reemplace el elemento del filtroRepita los pasos 1 y 2 hasta que el motor ya no arranque Mantenimiento de la silenciadorAlmacenamiento de Largo Plazo Retire la malla y limpie con un cepillo de cerdas gruesasDiscos de dientes múltiples Disco Shindaiwa TornadoPosible causa Guía DiagnósticoEL Motor no Arranca Qué revisarEl motor golpea Baja Potencia¿Se sobrecalienta el motor? Limpiar, reparar o sustituir en caso necesarioGuía Diagnóstico continuación Que Está Cubierto Por Esta Garantía Esta garantía es administrada porSus Derechos y Obligaciones de Garantía Cobertura de la Garantía del FabricanteTualatin, Oregon 97062 USA 11, Ozuka-Nishi COUPE-BORDURE T3410/EVC T3410X/EVC Mises en garde Table des matièresÉtiquettes de sécurité SécuritéSécurité au travail Demeurer alerteÉquipement complet de l’utilisateur Sécurité suiteCaractéristiques techniques NomenclatureFR6 AssemblageAvant l’assemblage Poignée y Barre de sécurité X appareilFR7 Assemblage suitePÁHFWHXU PÁHFWHXULQIpULHXUlorsque la tête’engrenage et des supports Installer la tête de coupeRéglage du jeu du levier d’accélération Retirer la clé hexagonale du boîtierInstallation de la lame de débroussailleuse Réduire les risques d’incendie Mélange de carburantRemplissage du réservoir à carburant Exemples de quantités de mélange de carburant àLorsque le moteur démarre Démarrage du moteurContrôle de l’état de l’appareil Démarrage du moteur suiteArrêt du moteur Réglage du ralenti du moteurFonctionnement Fonctionnement suite Entretien Entretien aux 50 heures Entretien suiteEntretien aux 10 heures Entretien aux 10 à 15 heuresRéglage du jeu des soupapes Remplacement du filtre à carburantEntretien toutes les 50 heures suite Entretien aux 139 heuresEntretien du silencieux Remisage à long termeAffûtage de la lame Lame Shindaiwa TornadoLame circulaire à plusieurs dents Points à contrôler SolutionGuide de dépannage LE Moteur NE Démarre PASLe moteur cogne Guide de dépannage suitePuissance Insuffisante Le moteur surchauffe-t-il ?Autres Problèmes Points à contrôler Cause probable SolutionCouverture de la garantie La présente garantie est administrée parVos droits et obligations en vertu de la garantie Couverture de la garantie des fabricants

T3410X/EVC, T3410/EVC, 89301 specifications

Shindaiwa is renowned for its durable and high-performing outdoor power equipment, and models like the Shindaiwa 89301, T3410/EVC, and T3410X/EVC highlight this reputation. These models are designed for both commercial and residential use, featuring advanced technologies that enhance performance and user experience.

The Shindaiwa 89301 is a versatile and powerful equipment that excels in various landscaping tasks. Its most notable feature is its robust engine, which provides exceptional power while maintaining fuel efficiency. This model incorporates Shindaiwa's advanced Clean Air Technology, which significantly reduces emissions, making it environmentally friendly and compliant with stringent regulations. The ergonomic design of the handle ensures comfort during prolonged use, reducing operator fatigue.

Moving on to the T3410/EVC, this model is primarily a brushcutter, known for its reliability and ease of use. It is equipped with a high-quality cutting system that delivers precise cuts and efficient grass clearing. The T3410/EVC features a powerful engine that provides strong torque at low RPMs, allowing for effective cutting through thick grass and weeds. One of the standout technologies in this unit is the E-Vac system, which enhances airflow in the cutting head for improved debris discharge. This ensures a clean and efficient cut, reducing the time spent on yard work.

Meanwhile, the T3410X/EVC model pushes the boundaries even further with additional capabilities. It features a more advanced ignition system that offers quicker starts and better overall performance in challenging conditions. This model also boasts a reinforced frame and components designed for demanding tasks, making it ideal for professionals who require reliability and performance. Just like the T3410/EVC, the T3410X/EVC is integrated with an advanced vibration dampening system, enhancing user comfort and control during operations.

Both models' user-friendly controls and lightweight design make them accessible for both seasoned professionals and casual users. Whether you are tackling a large commercial property or maintaining your backyard, Shindaiwa’s models 89301, T3410/EVC, and T3410X/EVC deliver exceptional performance, durability, and innovation, ensuring that your outdoor projects are completed efficiently and effectively. With a combination of power, technology, and ergonomic design, these models stand out in the competitive landscape of outdoor power equipment.
Top Page Image Contents