Shindaiwa 81646 manual Starting the Engine, Stopping the Engine, Adjusting Engine Idle

Page 10

Starting the Engine (continued)

WARNING!

The cutting attachment may rotate when the engine is started!

5.When the engine starts, slowly move the choke lever to the "OPEN" posi- tion. See Figure 0. (If the engine stops after the initial start, close the choke and restart.)

Open

WARNING!

Never start the engine from the operating position.

IMPORTANT!

If the engine fails to start after several attempts with the choke in the closed position, the engine may be flooded with fuel. If flooding is suspected, move the choke lever to the open posi- tion and repeatedly pull the recoil starter to remove excess fuel and start the engine. If the engine still fails to start, refer to the troubleshooting section of this manual.

When the Engine Starts

nAfter the engine starts, allow the engine to warm up at idle  or 3 minutes before operating the unit.

nAfter the engine is warm, pick up the unit and clip on the shoulder strap if so equipped. See page 11.

nAdvancing the throttle makes the cut- ting attachment turn faster; releasing the throttle permits the attachment to stop turning. If the cutting attachment continues to rotate when the engine returns to idle, carburetor idle speed should be adjusted (see "Adjusting Engine Idle" below).

26121

Figure 20

Stopping the Engine

OFF

26122

Figure 21

Idle the engine briefly before stopping (about  minutes), then slide the ignition switch to the “O” (Engine OFF) position.

Adjusting Engine Idle

Idle Adjusting

Screw

26123

Figure 22

10

The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment.

Idle Speed Adjustment

1.Place the trimmer on the ground, then start the engine, and allow it to idle -3 minutes until warm.

WARNING!

The cutting attachment must NEVER rotate at engine

idle! If the idle speed cannot be adjusted by the procedure described here, return the trimmer to your Shindaiwa dealer for inspection.

. If the attachment rotates when the engine is at idle, reduce the idle speed by turning the idle adjustment screw counter-clockwise.

See Figure .

3.If a tachometer is available, the engine idle speed should be final adjusted to ,750 (±50) rpm (min-1).

4.Carburetor fuel mixture adjustments are preset at factory and cannot be serviced in the field.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents T261 Trimmer T261X Trimmer Contents IntroductionStay Alert General Safety Instructions The Properly Equipped OperatorWork Safely Minimize the Risk FireSafety Labels Be Aware of the Working EnvironmentSpecifications Product DescriptionPrior to Assembly Assembly and AdjustmentsAdjust Throttle Lever Free Play HandleInstall the Trimmer Head Assembly Cutting Attachment ShieldAssembly Trimmer Head Install the Cutting Attachment ShieldNever operate the T261X without the safety clip in place Assembly Blade T261XMount the Cutting Blade Starting the Engine Mixing FuelFilling the Fuel Tank Examples of 501 mixing quantitiesIdle Speed Adjustment Adjusting Engine IdleWhen the Engine Starts Starting the EngineShoulder Strap Checking Unit ConditionCutting Grass-Units Equipped with a Trimmer Head Using a Blade T261X Daily Maintenance General MaintenanceHour Maintenance 10/15-Hour Maintenance Hour MaintenanceBlade Sharpening Hour MaintenaceLong Term Storage Shindaiwa Tornado BladeTroubleshooting Guide Engine does not StartLOW Power Output Additional Problems Exceptions Purchased Repair Parts and Accessories 99922201033 Page Page Servicing Information Parts/Serial NumberManual Del Propietario/Operador Shindaiwa ¡ADvERTENCIAContenido Introducción Declationes De Seguridad¡ADvERTENCIA Trabaje con cuidado El Operario Debidamente EquipadoMantengase Alerta Esté Alerta del Area de Trabajo Etiquetas de SeguridadEspecificaciones Descripción del ProductoDas a ninguna de éstas máquinas ni a sus componentes Ajuste la holgura del acelerador Ensamblaje y AjustesMango Antes de EnsamblarPara cambiar la posición de la cuchilla de corte Ensamblaje Cabezal de CorteInstalación del Cabezal de Corte Monte la Cuchilla de Corte Ensamblaje Disco/Cuchilla T261XNunca opere la T261 sin el retén de seguridad instalado Arranque del Motor Mezcla de CombustibleLlenando el Tanque de Combustible Disminuya el riesgo de incendiosCuando arranca el motor Parada del MotorAjuste de Marcha Mínima del Motor Ajuste de Marcha MínimaCorrea de Arnés Verifique la Condición de la UnidadCorte de Césped Máquinas Equipadas con Cabezal de Corte Usando un disco T261X Mantenimiento Diario Mantenimiento GeneralMantenimiento Cada 10-Horas Mantenimiento cada 10/15-Horas Mantenimiento Cada 50-HorasAfilado de Discos Mantenimiento Cada 135-HorasAlmacenamiento de Largo Plazo Disco Shindaiwa TornadoGuía Diagnóstico El Motor No ArrancaGuía Diagnóstico continuación Baja Potencia’ntoma Posible Causa Remedio Responsabilidad DE Echo Piezas DE Reparación COMPRADAS, Bloques Cortos Y Accesorios 01/2010 Cobertura DE Garantía DEL FabricanteNotas Notas Información de servicio Piezas/número de serie
Top Page Image Contents