Shindaiwa 81646 manual Assembly Cutting Attachment Shield, Assembly Trimmer Head

Page 7

Assembly: Cutting Attachment Shield

Install the Cutting Attachment Shield

1.Insert the cutting attachment shield between the outer tube and the cutting attachment mounting plate. See Figure 9.

NOTE:

It may be necessary to loosen the retaining nut and clamp screw to adjust cutting attach- ment shield mounting plate.

. Fit the two shims and the bracket over the outer tube and loosely install the four socket-head screws.

See Figure 9.

CAUTION!

Make sure the clamp screw and retaining nut are securely tightened before tightening the four socket- head cap screws.

Socket-

 

 

 

 

Head Cap

 

 

 

 

Screw

 

 

 

 

 

 

 

Outer

 

 

 

 

Tube

 

Bracket

 

 

 

Cutting Attach-

 

 

 

ment Shield

 

 

 

 

Shim

 

 

 

 

Clamp Screw

 

 

 

Nuts

 

 

 

 

 

 

 

 

Line Cutter

 

 

 

Shim

 

 

 

Cutting

 

 

 

Retaining

Attachment

 

 

26105

Mounting

Hex

 

 

Nut

Plate

 

 

Screws

 

Figure 9

 

 

Figure 9A

 

 

 

3.Tighten the four socket-head cap screws to secure the cutting attach- ment shield.

WARNING!

NEVER operate the unit without the cutting attach-

ment shield installed and tightly secured!

To Change Position of Line Cutter

The line cutter can be positioned in

positions to obtain different line length for cutting.

WARNING!

The line cutter is very sharp. Wear gloves to

protect your hands when handling.

1.Remove the  hex screws with a 4mm hex wrench. See Figure 9A.

NOTE:

Be careful to not lose the  nuts in the cutting attachment shield, they are not captured.

. Rotate line cutter. See Figure 9A.

3.Reinstall the two hex screws and tighten them securely.

Assembly: Trimmer Head

Install the Trimmer Head

1.Turn the trimmer over so that the gearcase output shaft faces UP.

. Remove and discard the black plastic retaining plug from the output shaft. See Figure 10.

3.

Rotate the holder until the hole in the

 

holder aligns with the notch on the

 

gearcase. Use the long end of the hex

 

wrench to lock the holder and output

 

shaft. See Figure 10.

4.

While holding the hex wrench, thread

 

the trimmer head onto the output shaft,

Retaining

Plug

Hex Wrench

Holder

Output

shaft

26106

26107

Figure 10

turning counter-clockwise. Using hand

pressure only, tighten the trimmer head

firmly on the output shaft.

IMPORTANT!

The trimmer head has a left-hand thread. For removal turn the trimmer head clock- wise.

5.Remove the hex wrench.

6.Adjust the trimmer line length to reach no further than the line

cutter on the cutting attachment shield. Trim to the correct length

if necessary.

WARNING!

A standard grass trimmer with a loop handle should

NEVER be operated with blade- type attachments. For blade use the trimmer must be fitted with a bicycle- type handlebar or a loop handle with a barrier bar that is located in front of the operator to reduce the risk of the operator coming in contact with the cutting attachment (per ANSI B175.3). When using a blade, the unit must also be equipped with a harness or strap.

To install a trimmer head onto a T261X, first remove the shaft bolt, bolt guard and safety clip (see the next page).

26108

Figure 11

The unit should now be

completely assembled and ready

for use with a trimmer head.

7

Image 7
Contents T261 Trimmer T261X Trimmer Introduction ContentsMinimize the Risk Fire General Safety Instructions The Properly Equipped OperatorWork Safely Stay AlertBe Aware of the Working Environment Safety LabelsProduct Description SpecificationsHandle Assembly and AdjustmentsAdjust Throttle Lever Free Play Prior to AssemblyInstall the Cutting Attachment Shield Assembly Cutting Attachment ShieldAssembly Trimmer Head Install the Trimmer HeadNever operate the T261X without the safety clip in place Assembly Blade T261XMount the Cutting Blade Examples of 501 mixing quantities Mixing FuelFilling the Fuel Tank Starting the EngineStarting the Engine Adjusting Engine IdleWhen the Engine Starts Idle Speed AdjustmentShoulder Strap Checking Unit ConditionCutting Grass-Units Equipped with a Trimmer Head Using a Blade T261X Daily Maintenance General MaintenanceHour Maintenance Hour Maintenance 10/15-Hour MaintenanceShindaiwa Tornado Blade Hour MaintenaceLong Term Storage Blade SharpeningEngine does not Start Troubleshooting GuideLOW Power Output Additional Problems Exceptions Purchased Repair Parts and Accessories 99922201033 Page Page Parts/Serial Number Servicing Information¡ADvERTENCIA Manual Del Propietario/Operador ShindaiwaContenido Introducción Declationes De Seguridad¡ADvERTENCIA Trabaje con cuidado El Operario Debidamente EquipadoMantengase Alerta Etiquetas de Seguridad Esté Alerta del Area de TrabajoEspecificaciones Descripción del ProductoDas a ninguna de éstas máquinas ni a sus componentes Antes de Ensamblar Ensamblaje y AjustesMango Ajuste la holgura del aceleradorPara cambiar la posición de la cuchilla de corte Ensamblaje Cabezal de CorteInstalación del Cabezal de Corte Monte la Cuchilla de Corte Ensamblaje Disco/Cuchilla T261XNunca opere la T261 sin el retén de seguridad instalado Disminuya el riesgo de incendios Mezcla de CombustibleLlenando el Tanque de Combustible Arranque del MotorAjuste de Marcha Mínima Parada del MotorAjuste de Marcha Mínima del Motor Cuando arranca el motorCorrea de Arnés Verifique la Condición de la UnidadCorte de Césped Máquinas Equipadas con Cabezal de Corte Usando un disco T261X Mantenimiento Diario Mantenimiento GeneralMantenimiento Cada 10-Horas Mantenimiento Cada 50-Horas Mantenimiento cada 10/15-HorasDisco Shindaiwa Tornado Mantenimiento Cada 135-HorasAlmacenamiento de Largo Plazo Afilado de DiscosEl Motor No Arranca Guía DiagnósticoBaja Potencia Guía Diagnóstico continuación’ntoma Posible Causa Remedio Responsabilidad DE Echo Piezas DE Reparación COMPRADAS, Bloques Cortos Y Accesorios Cobertura DE Garantía DEL Fabricante 01/2010Notas Notas Piezas/número de serie Información de servicio