Multiquip PS403016 Safety Message Alert Symbols, For Your Safety and the Safety of Others

Page 10

SAFETY MESSAGE ALERT SYMBOLS

FOR YOUR SAFETY AND THE SAFETY OF OTHERS!

Safety precautions should be followed at all times when operating this equipment. Failure to read, understand and comply with the Safety Messages and Operating Instructions could result in injury to yourself and others.

This Operation Manual has been developed to provide instructions for the safe and efficient operation of the MQ PS4030 Saw . For engine maintenance information, please refer to the engine manufacturer's instructions for data relative to its safe operation.

Before using this Saw, ensure that the operating individual has read, understands, and complies with all instructions in this manual.

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform you about potential hazards that could injure you or others. The Safety Messages specifically address the level of exposure to the operator, and are preceded by one of three words: DANGER, WARNING, or CAUTION.

HAZARD SYMBOLS

Lethal Exhaust Gases

Engine exhaust gases contain harmful toxins and will displace oxygen when running in an enclosed or confined area. NEVER operate this equipment in a confined area or enclosed structure that does not provide ample free flow air.

Explosive Fuel

Diesel fuel is flammable, and its vapors can cause an explosion if ignited. DO NOT start the engine near spilled fuel or combustible fluids. DO NOT fill the fuel tank while the engine is running or hot. DO NOT overfill tank, since spilled fuel could ignite if it comes into contact with hot engine parts or sparks from the ignition system. Store fuel in approved containers, in well-ventilated areas and away from sparks and flames. NEVER use fuel as a cleaning agent.

DANGER

You WILL be KILLED or SERIOUSLY INJURED if you DO NOT follow these directions.

WARNING

You CAN be KILLED or SERIOUSLY INJURED if you DO NOT follow these directions.

CAUTION

You CAN be INJURED if you DO NOT follow these directions.

Potential hazards associated with Saw operation will be referenced with Hazard Symbols which appear throughout this manual, and will be referenced in conjunction with Safety Message Alert Symbols.

Burn Hazards

Engine components can generate extreme heat. To prevent burns, DO NOT touch these areas while the engine is running or immediately after operations. NEVER operate the engine with heat shields or heat guards removed.

Rotating Parts

NEVER operate equipment with covers, or guards removed. Keep fingers, hands, hair and clothing away from all moving parts to prevent injury.

Skin Injection Hazard

NEVER use your hand to find hydraulic leaks. Use a piece of wood or cardboard. Hydraulic fluid injected into the skin must be treated by a knowledgable physician immediately or severe injury or death can occur.

PAGE 10 — MQ PS4030 SAW • OPERATION MANUAL — REV. #0 (02/29/08)

Image 10
Contents Models Page Silicosis Warning MQ PS4030 SAW Table of Contents MQ PS4030 SAW Dimensions Chassis & Dimensions SideviewBlade Shaft Assembly MQ PS4030 SAW SpecificationsOil bath design, fully enclosed cast iron housing Crated Weight MQ PS4030 SAW Engine SpecificationsUncrated Weight Automatic actuating parking brake Wheels RearTraining Checklist Training ChecklistDaily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistSafety Message Alert Symbols For Your Safety and the Safety of OthersAlways wear approved respiratory protection Safety Message Alert SymbolsAlways wear approved eye and hearing protection MQ PS4030 SAW Rules for Safe Operation SafetyDo not operate or service this Rules for Safe OperationMQ PS4030 SAW Rules for Safe Operation Always keep the work area well organizedDiamond Blade Safety Transporting Via truck/trailer Saw Lifting and Loading SafetyMQ PS4030 SAW Rules for Safe Operation Never transport the saw with the blade mountedMaintenance Safety BatteryCase the battery liquid dilute EmergenciesIntended Use FeaturesMQ PS4030 SAW Intended USE / Familiarization EngineMQ PS4030 SAW Operation and Safety Decals Machine Safety DecalsMQ PS4030 SAW Serial TAG Information Serial Tag/Locations SerialTagAuxiliary Switch MQ PS4030 SAW Controls and IndicatorsSocket Connector Use to plug in optional light LeftWater FlowValve Meters water supplyMQ PS4030 SAW Components Oil in crankcase MQ PS4030 SAW Basic Engine InformationAccelerator system Oil Fill Cap Remove to add engine oilRatio MQ PS4030 SAW Choosing Proper Blade SizeChoosing Proper Blade Size Engine RPM / 2000 desired BS RPM =MQ PS4030 SAW Choosing Proper Blade Size Blade RPM vs. Surface Feet Per Minute SfpmMQ PS4030 SAW Specific Tools / SAW Blades Specifictoolsto be UsedAlign flange pin through the blade into the inner flange MQ PS4030 SAW Installing the BladeInstalling the Blade Blade Direction of Rotation Tightening Direction Right Side12 In .48 cm Lbs 56.7-79.4 Kg MQ PS4030 SAW Installing the Blade125-175lbs.56.7-79.4Kgofweight Stacking Blades for Wide CutsMQ PS4030 SAW Blade Guards Blade GuardMQ PS4030 SAW Blade Guards Blade Guards 30 and SmallerInstalling the Flange Guard MQ PS4030 SAW Water Delivery SystemsMQ PS4030 SAW Battery Battery SetupHandle fuel safely MQ PS4030 SAW Fueling the SAWFueling the Saw Do not smoke while refuelingCold Weather Operation MQ PS4030 SAW Pointer AdjustmentPointer Adjustment Draining theWater SystemRaise Lower Controls Setting the Depth IndicatorMQ PS4030 SAW RAISE-LOWER Controls Top ViewDepth Control Knob Depth Indicator Pointer Setting the Depth StopMQ PS4030 SAW Bladeshaft Engage System Wheel Drive System MQ PS4030 SAW OperationStarting and Stoppingthe Engine Restarting After Running Out of Fuel MQ PS4030 SAW OperationOperating Synopsis MQ PS4030 SAW Loading and Transporting Avoid InjuryMQ PS4030 SAW Maintenance MaintenanceMQ PS4030 SAW Maintenance Air Cleaner ComponentsOil Filter 125 Hours Changing Engine Oil And FilterEngine Oil Filter Filter Seal Prevent Crush Injury Fuel Filter 200 HoursLubrication Engine Tune-UpCooling System Battery/Charging SystemRefer to your engine manual for additional information Remove rear access panel MQ PS4030 SAW MaintenanceReplacing the Battery Remove lower battery retainer, Item B, FigureTo Stop Bladeshaft Rotation Belts and PulleysTo Start Bladeshaft Rotation 16 Nut Tensioner Nut Adjustment Notches Blade Shaft MaintenanceRotary BeltTensioner Blade Alignment Drive System AlignmentBlade Flange Puller Removing the Inner Blade Flange If the Inner Flange does not readily Blade Shaft Tolerance Inner Flange Inside FaceWhile adjustment of the Depth Maximum Cut Depth AdjustmentCircuit Breakers PTO Drive Maintenance Raise-Lower SystemRaise-Lower System Troubleshooting Push-Pull Cable Neutral Safety Switch R Control AdjustmentAdjustment Nut Rod End Hydraulic System MaintenanceHydraulic System Hydraulic System DrainsDecommissioning Saw/Components Remove the oil reservoir cap to speed oil drainingLong Term Storage Slurry Control StripMQ PS4030 SAW Troubleshooting MQ PS4030 SAW Troubleshooting Symptom Possible Cause SolutionBlade Troubleshooting Page MQ PS4030 SAW Wiring Diagram Terms and Conditions of Sale Parts Canada Brazil United StatesMexico United Kingdom Your Local Dealer is