Multiquip PS403026 Safety Message Alert Symbols, Always wear approved respiratory protection

Page 11

SAFETY MESSAGE ALERT SYMBOLS

Accidental Starting

Accidental starts can cause severe injury or death. ALWAYS place the ON/OFF switch in the OFF position. Disconnect negative battery cable from battery before servicing.

Respiratory Hazard

ALWAYS wear approved respiratory protection.

Over Speed Conditions

NEVER tamper with the factory settings of the engine governor or settings. Personal injury and damage to the engine or equipment can result if operating in speed ranges above maximum allowable.

Rotating Blade

Rotating blade can cut and crush. Keep hands and feet clear.

Guards and Covers In Place

Sight and Hearing hazard

ALWAYS wear approved eye and hearing protection.

Equipment Damage Messages

Other important messages are provided throughout this manual to help prevent damage to your saw, other property, or the surrounding environment.

NEVER operate the saw without blade guards and covers in place. Adhere to safety guidelines and applicable local regulations.

Crush Hazard

ALWAYS ensure saw is SECURELY placed on appropriate blocks or jackstands when performing maintenance requiring the saw to be elevated.

MQ PS4030 SAW • OPERATION MANUAL — REV. #0 (02/29/08) — PAGE 11

Image 11
Contents Models Page Silicosis Warning MQ PS4030 SAW Table of Contents Chassis & Dimensions Sideview MQ PS4030 SAW DimensionsOil bath design, fully enclosed cast iron housing MQ PS4030 SAW SpecificationsBlade Shaft Assembly Automatic actuating parking brake Wheels Rear MQ PS4030 SAW Engine SpecificationsUncrated Weight Crated WeightTraining Checklist Training ChecklistDaily PRE-OPERATION Checklist Daily PRE-OPERATION ChecklistFor Your Safety and the Safety of Others Safety Message Alert SymbolsAlways wear approved eye and hearing protection Safety Message Alert SymbolsAlways wear approved respiratory protection Rules for Safe Operation SafetyDo not operate or service this MQ PS4030 SAW Rules for Safe OperationAlways keep the work area well organized MQ PS4030 SAW Rules for Safe OperationDiamond Blade Safety Never transport the saw with the blade mounted Saw Lifting and Loading SafetyMQ PS4030 SAW Rules for Safe Operation Transporting Via truck/trailerEmergencies BatteryCase the battery liquid dilute Maintenance SafetyEngine FeaturesMQ PS4030 SAW Intended USE / Familiarization Intended UseMachine Safety Decals MQ PS4030 SAW Operation and Safety DecalsSerial Tag/Locations SerialTag MQ PS4030 SAW Serial TAG InformationLeftWater FlowValve Meters water supply MQ PS4030 SAW Controls and IndicatorsSocket Connector Use to plug in optional light Auxiliary SwitchMQ PS4030 SAW Components Oil Fill Cap Remove to add engine oil MQ PS4030 SAW Basic Engine InformationAccelerator system Oil in crankcaseEngine RPM / 2000 desired BS RPM = MQ PS4030 SAW Choosing Proper Blade SizeChoosing Proper Blade Size RatioBlade RPM vs. Surface Feet Per Minute Sfpm MQ PS4030 SAW Choosing Proper Blade SizeSpecifictoolsto be Used MQ PS4030 SAW Specific Tools / SAW BladesBlade Direction of Rotation Tightening Direction Right Side MQ PS4030 SAW Installing the BladeInstalling the Blade Align flange pin through the blade into the inner flangeStacking Blades for Wide Cuts MQ PS4030 SAW Installing the Blade125-175lbs.56.7-79.4Kgofweight 12 In .48 cm Lbs 56.7-79.4 KgBlade Guard MQ PS4030 SAW Blade GuardsBlade Guards 30 and Smaller MQ PS4030 SAW Blade GuardsMQ PS4030 SAW Water Delivery Systems Installing the Flange GuardBattery Setup MQ PS4030 SAW BatteryDo not smoke while refueling MQ PS4030 SAW Fueling the SAWFueling the Saw Handle fuel safelyDraining theWater System MQ PS4030 SAW Pointer AdjustmentPointer Adjustment Cold Weather OperationTop View Setting the Depth IndicatorMQ PS4030 SAW RAISE-LOWER Controls Raise Lower ControlsMQ PS4030 SAW Bladeshaft Engage System Setting the Depth StopDepth Control Knob Depth Indicator Pointer Starting and Stoppingthe Engine MQ PS4030 SAW OperationWheel Drive System Operating Synopsis MQ PS4030 SAW OperationRestarting After Running Out of Fuel Avoid Injury MQ PS4030 SAW Loading and TransportingMaintenance MQ PS4030 SAW MaintenanceAir Cleaner Components MQ PS4030 SAW MaintenanceEngine Oil Filter Filter Seal Changing Engine Oil And FilterOil Filter 125 Hours Engine Tune-Up Fuel Filter 200 HoursLubrication Prevent Crush InjuryRefer to your engine manual for additional information Battery/Charging SystemCooling System Remove lower battery retainer, Item B, Figure MQ PS4030 SAW MaintenanceReplacing the Battery Remove rear access panelTo Start Bladeshaft Rotation Belts and PulleysTo Stop Bladeshaft Rotation Rotary BeltTensioner Blade Shaft Maintenance16 Nut Tensioner Nut Adjustment Notches Drive System Alignment Blade AlignmentBlade Flange Puller Removing the Inner Blade Flange Blade Shaft Tolerance Inner Flange Inside Face If the Inner Flange does not readilyCircuit Breakers Maximum Cut Depth AdjustmentWhile adjustment of the Depth Raise-Lower System PTO Drive MaintenanceRaise-Lower System Troubleshooting Hydraulic System Maintenance R Control AdjustmentAdjustment Nut Rod End Push-Pull Cable Neutral Safety SwitchHydraulic System Drains Hydraulic SystemSlurry Control Strip Remove the oil reservoir cap to speed oil drainingLong Term Storage Decommissioning Saw/ComponentsMQ PS4030 SAW Troubleshooting Symptom Possible Cause Solution MQ PS4030 SAW TroubleshootingBlade Troubleshooting Page MQ PS4030 SAW Wiring Diagram Terms and Conditions of Sale Parts Your Local Dealer is United StatesMexico United Kingdom Canada Brazil