Land Pride 357-044M manual Electrical Cable Connection, Engine Preparations

Page 11

Land Pride

Table of Contents

Section 1: Assembly & Set-up

IMPORTANT: Do not pull a trailer or implement exceeding 300 pounds towing capacity and 50 pounds tongue weight. Loss of control may result. Do not make turns that will cause a trailer or implement being towed with the hitch to come in contact with the mower or damage may result.

Electrical Cable Connection

Refer to Figure 1-3:

!WARNING

Incorrect battery cable connections can damage mower’s electrical system and cause battery cables to spark. Sparks around a battery can result in a battery gas explosion and personal injury.

Connect the black negative battery cable to the battery’s negative post with 1/4"-20 x 3/4" GR5 hex head serrated screw, flat washer, lock washer and nut before starting the mower. Tighten hex nut to 8 ft. lbs. of torque.

Engine Preparations

1.Check engine oil level at the dipstick. Add oil if oil is below the full mark on the dipstick. Do not overfill. Refer to engine manual for oil recommendation. Also see "Engine Oil and Oil Filter" instructions on page 32.

NOTE: Vehicles are shipped from the factory with about a quart of fuel in the tank.

2.See "Fuel System" instructions on page 31 before adding fuel. Add fuel to the fuel tank.

•Always disconnect negative (black) battery cable before disconnecting positive (red) cable.

•Always reconnect positive (red) battery cable to the positive (+) post before reconnecting negative (black) cable to the negative (-)post.

!WARNING

Keep battery terminals from touching any metal mower parts when removing or installing the battery. Do not allow metal tools to short between the battery terminals and metal mower parts. Shorts caused by battery terminals or metal tools touching metal mower components can cause sparks. Sparks can cause a battery gas explosion which will result in personal injury.

Black Negative

Battery Cable

Negative

Post

Connecting the Negative Cable

Figure 1-3

IMPORTANT: The negative battery cable is disconnected before leaving the factory and is to be disconnected after initial dealer set-up to prevent battery discharge while setting on the dealer lot.

Remove Mower From Crate Floor

IMPORTANT: Thoroughly read and understand

"Section 2: Operating Procedures", pages 10 to 18 before starting and moving the mower.

1.Make a ramp in front and level with the crate floor to be used for driving the mower off.

2.Check under the mower to make sure it is not banded to the crate floor. Remove any bands that are still present.

3.Follow all precautions and operating information provided in "Section 2: Operating Procedures" before starting and driving the mower off.

4.Raise deck fully up.

5.Start the engine and drive the mower forward off the crate floor.

6.Make necessary adjustments to the mower as outlined in "Section 3: Adjustments" beginning on page 19.

2/27/07

Z44 & Z52 (S/N 472620 -526170) Zero Turning Radius Mowers Riding Mowers Accu-Z Razor® 357-044M

9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Riding Mowers Accu-Z Razor Table of Contents Safety at All Times Avoid High Pressure Fluids Hazard Practice Safe MaintenanceKeep Riders Off Machinery Wear Protective Equipment Prepare for Emergencies838-815C 838-303C838-307C 838-308C 838-833C 838-310C 818-543C Owner Assistance Using This ManualApplication Uncrating Instructions Control Lever AssemblySeat Assembly Hitch Plate AssemblyRemove Mower From Crate Floor Electrical Cable ConnectionEngine Preparations Muffler Shield Is Located Under Engine Mower FeaturesRazor Features Land PrideTable of Contents Park Lever Blade Engagement SwitchLeft/Right Fuel Tank Valve Control LeversDeck Lift Pedal Safety Start Interlock SystemDeck Height Deck Lift Locking Pin Pedal Indicator Engine StartingSteering Driving the MowerTo Decrease Speed or Stop To Start and Increase SpeedBypass Valve Rods Moving Mower with Stalled EngineFront of Mower Faces This Direction SteeringSafe Operating Instructions Discharge Chute Blade Blade Engagement SwitchMower Deck Operation General Operating InformationFT lbs Torque ValuesSteering Linkage Torque ValuesSteering Dampener Control Lever Neutral AdjustmentReach Adjustment Seat AdjustmentUpper Control Lever Adjustments Height AdjustmentDeck Leveling & Height Adjustment Hydro-Drive Belt AdjustmentEngine RPM Setting Deck Drive Belt AdjustmentStop Handle Height Adjusting StopAdjuster Bolt Jam Nut Hardware Refer to -9& Figure Refer to FigureLift Deck Lift Rod Adjustment Left Front Side ShownRefer to -10on Refer to -12on Deck Cutting Height AdjustmentAnti-Scalp Rollers Pivot Front WheelsDeck Bottom View Drive motors removed for clarity Maintenance LocationsService at Intervals Indicated Every Refer to Hours Maintenance ScheduleMaintenance Electrical System BatteryWiring Harness Fusses TiresRefer to Refer to Figure Access to IZT Units Integrated Zero-Turn TransaxleHydraulic System Hydraulic oil and FilterFuel System Oil Check, Honda Engine Fuel FilterDraining The Fuel Tank Engine Oil and Oil FilterEngine Air Filter General Engine MaintenanceBelt Replacement Deck Belt Replacement InstructionsRefer to -11on Mower Blade MaintenanceDrive Belt Replacement Instructions Blade InspectionRefer to -15and Figure Blade SharpeningNew Season Preparation StoragePreparation of Engine for Storage Left Blade Spindle Lubrication PointsHours Center Blade SpindleDeck Lift Pivot Points 100/M HoursGauge Wheel Bearing Zerk Front Axle Center PivotEngine Type Z44 & Z52 Accu-Z Razor Engine SpecificationsZ44 & Z52 Accu-Z Razor General Specifications Specifications to continue on nextIndicators Brake ServiceSafety Features Deck Housing DepthPark lever to OFF Hydro-Gear IZT Features BenefitsZ44 & Z52 Accu-Z Razor For the operator Steering levers designed forOverheating Engine cranks but does not startEngine Either directionLevers are in neutral Mower creeps when steering controlOne direction only Hydraulic system operates hotIn-tpi Torque Values ChartTire Inflation Chart Additional Torque ValuesBelts, blades, and tires are considered wear items WarrantyCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

357-044M specifications

The Land Pride 357-044M is a cutting-edge implement designed to meet the needs of professionals and enthusiasts in the agricultural sector. Known for its robust construction and innovative features, this attachment is ideal for enhancing productivity in various land management tasks.

One of the main features of the Land Pride 357-044M is its heavy-duty design, which is specifically built to withstand the rigors of daily use in demanding environments. The durable frame ensures longevity, allowing operators to tackle tough soil conditions without worrying about equipment failure. Additionally, the implement is equipped with high-quality materials that resist wear and tear, providing peace of mind for long-term reliability.

The 357-044M shines in its versatility. It can be used for a variety of applications, such as leveling ground, grading, and even snow removal in winter months. With adjustable features, operators can easily modify the attachment to suit specific job requirements, making it a multi-functional tool for land preparation.

Equipped with advanced technologies, the Land Pride 357-044M includes precision-engineered components that optimize performance. The attachment’s unique blade design enhances soil mixing and aeration, leading to improved crop yields. Furthermore, the implement's innovative hydraulic system allows for smooth and efficient operation, ensuring that the tool can be adapted to different tasks with minimal effort.

Operator comfort and efficiency are also key characteristics of the 357-044M. The implement features user-friendly controls, making it easy to operate even for those who may be unfamiliar with such equipment. The design takes into account ease of attachment and detachment from various tractors, promoting a seamless workflow on the job site.

In summary, the Land Pride 357-044M is a versatile and dependable implement that combines a robust design, innovative technologies, and operator-friendly features. Its ability to perform multiple tasks makes it an essential addition to any agricultural operation. With a focus on durability and efficiency, this attachment is sure to stand the test of time while delivering the performance that land management professionals demand.
Top Page Image Contents