Land Pride 357-044M manual Refer to -10on, Deck Lift Rod Adjustment Left Front Side Shown

Page 26

Table of Contents

Section 3: Adjustments

Land Pride

Refer to Figure 3-12:

9.Start the leveling process on the left front side of the mower.

10.Set the amount of threads on the deck lift rod to protrude approximately 1” pass the lift block.

11.Jam both nuts against the lift block.

12.Push or pull on the deck lift foot pedal until the chain on the left front just becomes tight, making sure that the deck stays tight against the 3” block.

Lift

1” Protrusion

Deck Lift

Assist

Block

 

 

Spring

 

 

 

1”

 

Deck

Lift Rod

Nuts

 

Left Front

23690

Deck Lift Chain

Deck Lift Rod Adjustment (Left Front Side Shown)

Figure 3-12

Refer to Figure 3-11:

13.While keeping the left front chain tight, tighten the nuts against the deck lift block on the height indicator rod.

Refer to Figure 3-10on Page 23:

14.Go to the right front of the mower.

15.Loosen the 5/16” jam nut for the 5/16" adjuster bolt and then back the adjuster bolt out to allow the adjuster to move up and down freely.

16.Be sure that the adjuster is free to move up and down. Tighten the adjuster bolt until the chain just becomes tight. Make sure the deck stays tight against the 3” block.

17.Tighten the adjuster bolt jam nut to prevent the adjuster bolt from moving.

18.Tighten the hardware holding the chain and adjuster onto the deck lift arm.

Refer to Figure 3-13

19.Go to the right rear of the mower.

20.Make sure that there is still slack in the back right lift chain. If not, loosen the two nuts (“A” & “B”) on the lift block until there is slack in the right rear deck lift chain.

21.Tighten “B” nut until the chain just becomes tight, making sure that the deck stays tight against the 3” block.

23691

Threaded Rod

“A” Nut

Lift Block

“B” Nut

Right Rear

Deck Lift Chain

Deck Lift Rod Adjustment (Right Back Side Shown)

Figure 3-13

Refer to Figure 3-14:

22.Go to the left rear of the mower.

23.Make sure that there is still slack in the chain. If not, loosen the two nuts (“A” & “B”) on the lift block until there is slack in the left rear deck lift chain.

24.Tighten “B” nut until the chain just becomes tight, making sure that the deck stays tight against the 3” block.

25.Tighten both RH and LH “B” nuts one more full turn to raise rear of the deck to be approximately 1/4" higher than the front.

26.Tighten “A” nut on both sides to jam it and “B” nut tightly against the lift block.

23690

Lift

 

 

Block

Deck

Lift Rod

“A” Nut

“B” Nut

Left Rear

Deck Lift Chain

Deck Lift Rod Adjustment (Left Rear Side Shown)

Figure 3-14

24 Z44 & Z52 (S/N 472620 -526170) Zero Turning Radius Mowers Riding Mowers Accu-Z Razor® 357-044M

2/27/07

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Riding Mowers Accu-Z Razor Table of Contents Safety at All Times Avoid High Pressure Fluids Hazard Practice Safe MaintenanceKeep Riders Off Machinery Prepare for Emergencies Wear Protective Equipment838-303C 838-815C838-307C 838-308C 838-833C 838-310C 818-543C Owner Assistance Using This ManualApplication Hitch Plate Assembly Control Lever AssemblySeat Assembly Uncrating InstructionsRemove Mower From Crate Floor Electrical Cable ConnectionEngine Preparations Muffler Shield Is Located Under Engine Mower FeaturesRazor Features Land PrideTable of Contents Control Levers Blade Engagement SwitchLeft/Right Fuel Tank Valve Park LeverEngine Starting Safety Start Interlock SystemDeck Height Deck Lift Locking Pin Pedal Indicator Deck Lift PedalTo Start and Increase Speed Driving the MowerTo Decrease Speed or Stop SteeringSteering Moving Mower with Stalled EngineFront of Mower Faces This Direction Bypass Valve RodsSafe Operating Instructions Discharge Chute General Operating Information Blade Engagement SwitchMower Deck Operation BladeTorque Values Torque ValuesSteering Linkage FT lbsControl Lever Neutral Adjustment Steering DampenerHeight Adjustment Seat AdjustmentUpper Control Lever Adjustments Reach AdjustmentDeck Drive Belt Adjustment Hydro-Drive Belt AdjustmentEngine RPM Setting Deck Leveling & Height AdjustmentRefer to -9& Figure Refer to Figure Height Adjusting StopAdjuster Bolt Jam Nut Hardware Stop HandleLift Deck Lift Rod Adjustment Left Front Side ShownRefer to -10on Pivot Front Wheels Deck Cutting Height AdjustmentAnti-Scalp Rollers Refer to -12onMaintenance Locations Deck Bottom View Drive motors removed for clarityMaintenance Schedule Service at Intervals Indicated Every Refer to HoursMaintenance Tires BatteryWiring Harness Fusses Electrical SystemHydraulic oil and Filter Access to IZT Units Integrated Zero-Turn TransaxleHydraulic System Refer to Refer to FigureFuel System Engine Oil and Oil Filter Fuel FilterDraining The Fuel Tank Oil Check, Honda EngineDeck Belt Replacement Instructions General Engine MaintenanceBelt Replacement Engine Air FilterBlade Inspection Mower Blade MaintenanceDrive Belt Replacement Instructions Refer to -11onBlade Sharpening Refer to -15and FigureNew Season Preparation StoragePreparation of Engine for Storage Center Blade Spindle Lubrication PointsHours Left Blade SpindleFront Axle Center Pivot 100/M HoursGauge Wheel Bearing Zerk Deck Lift Pivot PointsSpecifications to continue on next Z44 & Z52 Accu-Z Razor Engine SpecificationsZ44 & Z52 Accu-Z Razor General Specifications Engine TypeDeck Housing Depth Brake ServiceSafety Features IndicatorsFor the operator Steering levers designed for Features BenefitsZ44 & Z52 Accu-Z Razor Park lever to OFF Hydro-Gear IZTEither direction Engine cranks but does not startEngine OverheatingHydraulic system operates hot Mower creeps when steering controlOne direction only Levers are in neutralAdditional Torque Values Torque Values ChartTire Inflation Chart In-tpiWarranty Belts, blades, and tires are considered wear itemsCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

357-044M specifications

The Land Pride 357-044M is a cutting-edge implement designed to meet the needs of professionals and enthusiasts in the agricultural sector. Known for its robust construction and innovative features, this attachment is ideal for enhancing productivity in various land management tasks.

One of the main features of the Land Pride 357-044M is its heavy-duty design, which is specifically built to withstand the rigors of daily use in demanding environments. The durable frame ensures longevity, allowing operators to tackle tough soil conditions without worrying about equipment failure. Additionally, the implement is equipped with high-quality materials that resist wear and tear, providing peace of mind for long-term reliability.

The 357-044M shines in its versatility. It can be used for a variety of applications, such as leveling ground, grading, and even snow removal in winter months. With adjustable features, operators can easily modify the attachment to suit specific job requirements, making it a multi-functional tool for land preparation.

Equipped with advanced technologies, the Land Pride 357-044M includes precision-engineered components that optimize performance. The attachment’s unique blade design enhances soil mixing and aeration, leading to improved crop yields. Furthermore, the implement's innovative hydraulic system allows for smooth and efficient operation, ensuring that the tool can be adapted to different tasks with minimal effort.

Operator comfort and efficiency are also key characteristics of the 357-044M. The implement features user-friendly controls, making it easy to operate even for those who may be unfamiliar with such equipment. The design takes into account ease of attachment and detachment from various tractors, promoting a seamless workflow on the job site.

In summary, the Land Pride 357-044M is a versatile and dependable implement that combines a robust design, innovative technologies, and operator-friendly features. Its ability to perform multiple tasks makes it an essential addition to any agricultural operation. With a focus on durability and efficiency, this attachment is sure to stand the test of time while delivering the performance that land management professionals demand.
Top Page Image Contents