Land Pride 357-044M manual Seat Adjustment, Upper Control Lever Adjustments, Height Adjustment

Page 23

Land Pride

Section 3: Adjustments

Table of Contents

3.Repeat step 2 to adjust the right dampener rod.

4.Check steering dampeners:

a.Move the control levers to reverse position and release. The control levers should return to neutral position.

b.Repeat steps 1 through 4 if control levers do not return to neutral position.

NOTE: The dampener must not bottom out when the pump lever is fully stroked in either direction.

Seat Adjustment

Refer to Figure 1-1on page 8:

IMPORTANT: The arm rests on the Deluxe Seat must be pivoted up before hinging the seat platform forward. Leaving the arm rests down while hinging the seat platform forward can cut the arm rest covers and void their warranty.

The seat platform is slotted so the seat can be adjusted to the operator. Loosen the seat mounting hardware located under the seat and adjust the seat forward or rearwards to a length that is comfortable for the operator to raise and lower the mower deck with his right foot. Tighten the seat mounting hardware once the seat is adjusted.

Upper Control Lever Adjustments

IMPORTANT: Do not make adjustment to the lower control levers since they are already adjusted for neutral creep on page 20.

The control levers may be adjusted while in the neutral position for height, reach and forward travel to fit the operator’s steering comfort zone.

Height Adjustment

Refer to Figure 3-4:

1.Adjust control levers vertically by removing the bolts, flat washers, and locknuts that attach the upper control levers to the lower control levers.

2.Reposition upper control levers to a height that fits the operator’s personal preference.

3.Reassemble bolts, flat washers, and locknuts in the same order they were removed without tightening them.

Reach Adjustment

Refer to Figure 3-4

1.Pivot the upper control levers forward or backward to fit the operator’s personal reach preference. If reach comfort zone can not be achieved, then try exchanging sides the levers are located:

a.Remove the bolts, flat washers, and locknuts that attach the upper control levers to the lower control levers.

b.Switch right control lever with left control lever and reassemble the bolts, flat washers, and locknuts in the same order they were removed without tightening them.

c.Pivot the upper control levers forward or backward to fit operator’s personal reach preference.

2.Verify that the control levers align with each other when in the neutral position and tighten the locknuts to the correct torque.

Upper Control Lever

Bolts with Flat

Washers, and

Locknuts

Lower Control Lever

23626

Control Lever Adjustment

Figure 3-4

Forward Travel Adjustment

Refer to Figure 3-4:

"Reach Adjustment" instructions are for adjusting the control levers to be equally aligned while in neutral. However, with this adjustment, the mower may want to steer slightly to the right or left when pushing the levers equally forward.

Make the following adjustments if you prefer to have the levers equally aligned while in forward travel position instead of while in neutral position:

1.While driving forward, make the necessary steering correction required to make the unit go straight and take careful notice of how the upper control levers are positioned. (The distance one lever is ahead of the other to make the mower travel straight.)

2.Stop the mower on a level surface, place the control levers in neutral, shut the power off and remove the switch key.

3.Either adjust the upper trailing lever forward by the distance it was trailing or adjust the upper leading lever back by the distance it was leading. Tighten the locknuts to correct torque.

Example:

If the right control lever is one inch ahead of the left control lever, stop the unit and either adjust the right upper control lever back one inch or adjust the left upper control lever forward one inch.

2/27/07

Z44 & Z52 (S/N 472620 -526170) Zero Turning Radius Mowers Riding Mowers Accu-Z Razor® 357-044M

21

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Riding Mowers Accu-Z Razor Table of Contents Safety at All Times Avoid High Pressure Fluids Hazard Practice Safe MaintenanceKeep Riders Off Machinery Wear Protective Equipment Prepare for Emergencies838-815C 838-303C838-307C 838-308C 838-833C 838-310C 818-543C Owner Assistance Using This ManualApplication Uncrating Instructions Control Lever AssemblySeat Assembly Hitch Plate AssemblyRemove Mower From Crate Floor Electrical Cable ConnectionEngine Preparations Muffler Shield Is Located Under Engine Mower FeaturesRazor Features Land PrideTable of Contents Park Lever Blade Engagement SwitchLeft/Right Fuel Tank Valve Control LeversDeck Lift Pedal Safety Start Interlock SystemDeck Height Deck Lift Locking Pin Pedal Indicator Engine StartingSteering Driving the MowerTo Decrease Speed or Stop To Start and Increase SpeedBypass Valve Rods Moving Mower with Stalled EngineFront of Mower Faces This Direction SteeringSafe Operating Instructions Discharge Chute Blade Blade Engagement SwitchMower Deck Operation General Operating InformationFT lbs Torque ValuesSteering Linkage Torque ValuesSteering Dampener Control Lever Neutral AdjustmentReach Adjustment Seat AdjustmentUpper Control Lever Adjustments Height AdjustmentDeck Leveling & Height Adjustment Hydro-Drive Belt AdjustmentEngine RPM Setting Deck Drive Belt AdjustmentStop Handle Height Adjusting StopAdjuster Bolt Jam Nut Hardware Refer to -9& Figure Refer to FigureLift Deck Lift Rod Adjustment Left Front Side ShownRefer to -10on Refer to -12on Deck Cutting Height AdjustmentAnti-Scalp Rollers Pivot Front WheelsDeck Bottom View Drive motors removed for clarity Maintenance LocationsService at Intervals Indicated Every Refer to Hours Maintenance ScheduleMaintenance Electrical System BatteryWiring Harness Fusses TiresRefer to Refer to Figure Access to IZT Units Integrated Zero-Turn TransaxleHydraulic System Hydraulic oil and FilterFuel System Oil Check, Honda Engine Fuel FilterDraining The Fuel Tank Engine Oil and Oil FilterEngine Air Filter General Engine MaintenanceBelt Replacement Deck Belt Replacement InstructionsRefer to -11on Mower Blade MaintenanceDrive Belt Replacement Instructions Blade InspectionRefer to -15and Figure Blade SharpeningNew Season Preparation StoragePreparation of Engine for Storage Left Blade Spindle Lubrication PointsHours Center Blade SpindleDeck Lift Pivot Points 100/M HoursGauge Wheel Bearing Zerk Front Axle Center PivotEngine Type Z44 & Z52 Accu-Z Razor Engine SpecificationsZ44 & Z52 Accu-Z Razor General Specifications Specifications to continue on nextIndicators Brake ServiceSafety Features Deck Housing DepthPark lever to OFF Hydro-Gear IZT Features BenefitsZ44 & Z52 Accu-Z Razor For the operator Steering levers designed forOverheating Engine cranks but does not startEngine Either directionLevers are in neutral Mower creeps when steering controlOne direction only Hydraulic system operates hotIn-tpi Torque Values ChartTire Inflation Chart Additional Torque ValuesBelts, blades, and tires are considered wear items WarrantyCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

357-044M specifications

The Land Pride 357-044M is a cutting-edge implement designed to meet the needs of professionals and enthusiasts in the agricultural sector. Known for its robust construction and innovative features, this attachment is ideal for enhancing productivity in various land management tasks.

One of the main features of the Land Pride 357-044M is its heavy-duty design, which is specifically built to withstand the rigors of daily use in demanding environments. The durable frame ensures longevity, allowing operators to tackle tough soil conditions without worrying about equipment failure. Additionally, the implement is equipped with high-quality materials that resist wear and tear, providing peace of mind for long-term reliability.

The 357-044M shines in its versatility. It can be used for a variety of applications, such as leveling ground, grading, and even snow removal in winter months. With adjustable features, operators can easily modify the attachment to suit specific job requirements, making it a multi-functional tool for land preparation.

Equipped with advanced technologies, the Land Pride 357-044M includes precision-engineered components that optimize performance. The attachment’s unique blade design enhances soil mixing and aeration, leading to improved crop yields. Furthermore, the implement's innovative hydraulic system allows for smooth and efficient operation, ensuring that the tool can be adapted to different tasks with minimal effort.

Operator comfort and efficiency are also key characteristics of the 357-044M. The implement features user-friendly controls, making it easy to operate even for those who may be unfamiliar with such equipment. The design takes into account ease of attachment and detachment from various tractors, promoting a seamless workflow on the job site.

In summary, the Land Pride 357-044M is a versatile and dependable implement that combines a robust design, innovative technologies, and operator-friendly features. Its ability to perform multiple tasks makes it an essential addition to any agricultural operation. With a focus on durability and efficiency, this attachment is sure to stand the test of time while delivering the performance that land management professionals demand.
Top Page Image Contents