Land Pride 357-044M manual Fuel Filter, Draining The Fuel Tank, Engine Oil and Oil Filter

Page 34

Table of Contents

Section 4: Maintenance & Lubrication

Land Pride

Fuel Filter

Refer to Figure 4-7:

!DANGER

Close fuel shut-off valve before replacing fuel filter. Otherwise, fuel can leak out creating a fire and/or explosion hazard.

The fuel filter is installed in the fuel line between the Left/Right Fuel Tank Valve and engine fuel pump. Location of fuel filter will vary depending on which engine your mower is equipped with. See engine owner’s manuals for exact location of fuel filter and instructions on removal and installation.

Replace filter annually or after every 100 hours of operation, whichever occurs first. Be sure to Install the fuel filter with Flow Arrow pointing towards the engine side of the fuel line. Always check fuel line hoses for any cracks or leaks. Replace as needed.

Flow Arrow Indicates direction fuel

must flow through the filter.

23803

Fuel Filter

Figure 4-7

Draining The Fuel Tank

1.Park the unit on a flat surface. Make sure blade engagement switch is in the down (OFF) position. Place control levers in park and set park lever to (ON). Stop engine and remove ignition key.

2.Disconnect negative battery cable.

3.Trace the fuel line from the tank to the tee under the Left/Right Fuel Tank Valve (Refer to Figure 4-8.Loosen the fuel line hose clamp at the tee and remove the fuel line from the tee.

4.Place the end of the fuel line into a gas can or a drain pan to drain the fuel tank.

5.When the fuel tank is drained, re-route the fuel line to the Left/Right Fuel Tank Valve and reattach with previously removed clamp.

Left/Right Fuel Tank Valve

Center Position “O” as Shown is OFF

23688

Fuel Shut-Off Valve (Honda Engine Location Shown)

Figure 4-8

located at the rear of the machine. Mower must be sitting level when checking oil. Refer to engine manual and maintenance schedule for oil recommendation and capacities.

Change the engine oil and filter after the first 5 hours of operation and per the engine manufacturer’s recommendations after that. It is recommended oil be changed more frequently if the mower is being operated in extremely dirty conditions.

Crankcase

Dipstick

Engine Oil

Filler Tube

Oil Filter

Oil Drain Plug

23631

Bumper Removed for Clarity

Oil Filter, Drain & Filler Tube (Honda Engine Shown)

Figure 4-9

The oil fill and dipstick are located on the right hand side for the Honda engine and left hand side for the Briggs & Stratton engine.The oil drain and oil filter are located on the right hand side for both engines.

Drain oil by unscrewing the oil drain plug (see Figure 4-9) as needed to allow oil to flow freely. Do not remove drain plug. Drain plug will offer resistance once it is unscrewed as far as it should be.

IMPORTANT: Make certain engine is level and you are inserting the dipstick correctly when checking oil. An oil overfill can cause engine problems.

Oil Check, Honda Engine

1.Unscrew oil filler cap/dipstick and wipe it clean.

2.Insert dipstick fully in without screwing it in and removing it again to check oil level.

3.If oil level is near or below the lower limit mark on the dipstick, fill with recommended oil to the upper limit mark. Do not overfill.

4.Reinstall oil filler cap/dipstick by screwing it in firmly.

Oil Check, Briggs & Stratton Engine

1.Unscrew oil filler cap/dipstick and wipe it clean.

2.Insert dipstick fully in by screwing it in and removing it again to check oil level.

Engine Oil and Oil Filter

Refer to Figure 4-9:

Check engine oil daily and after every 4 hours of operation. Crankcase dipstick and engine oil fill tube are

3.If oil level is near or below the lower limit mark on the dipstick, fill with recommended oil to the upper limit mark. Do not overfill.

4.Reinstall oil filler cap/dipstick by screwing it in firmly.

32 Z44 & Z52 (S/N 472620 -526170) Zero Turning Radius Mowers Riding Mowers Accu-Z Razor® 357-044M

2/27/07

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Riding Mowers Accu-Z Razor Table of Contents Safety at All Times Keep Riders Off Machinery Practice Safe MaintenanceAvoid High Pressure Fluids Hazard Prepare for Emergencies Wear Protective Equipment838-303C 838-815C838-307C 838-308C 838-833C 838-310C 818-543C Application Using This ManualOwner Assistance Hitch Plate Assembly Control Lever AssemblySeat Assembly Uncrating InstructionsEngine Preparations Electrical Cable ConnectionRemove Mower From Crate Floor Razor Features Mower FeaturesMuffler Shield Is Located Under Engine Land PrideTable of Contents Control Levers Blade Engagement SwitchLeft/Right Fuel Tank Valve Park LeverEngine Starting Safety Start Interlock SystemDeck Height Deck Lift Locking Pin Pedal Indicator Deck Lift PedalTo Start and Increase Speed Driving the MowerTo Decrease Speed or Stop SteeringSteering Moving Mower with Stalled EngineFront of Mower Faces This Direction Bypass Valve RodsSafe Operating Instructions Discharge Chute General Operating Information Blade Engagement SwitchMower Deck Operation BladeTorque Values Torque ValuesSteering Linkage FT lbsControl Lever Neutral Adjustment Steering DampenerHeight Adjustment Seat AdjustmentUpper Control Lever Adjustments Reach AdjustmentDeck Drive Belt Adjustment Hydro-Drive Belt AdjustmentEngine RPM Setting Deck Leveling & Height AdjustmentRefer to -9& Figure Refer to Figure Height Adjusting StopAdjuster Bolt Jam Nut Hardware Stop HandleRefer to -10on Deck Lift Rod Adjustment Left Front Side ShownLift Pivot Front Wheels Deck Cutting Height AdjustmentAnti-Scalp Rollers Refer to -12onMaintenance Locations Deck Bottom View Drive motors removed for clarityMaintenance Schedule Service at Intervals Indicated Every Refer to HoursMaintenance Tires BatteryWiring Harness Fusses Electrical SystemHydraulic oil and Filter Access to IZT Units Integrated Zero-Turn TransaxleHydraulic System Refer to Refer to FigureFuel System Engine Oil and Oil Filter Fuel FilterDraining The Fuel Tank Oil Check, Honda EngineDeck Belt Replacement Instructions General Engine MaintenanceBelt Replacement Engine Air FilterBlade Inspection Mower Blade MaintenanceDrive Belt Replacement Instructions Refer to -11onBlade Sharpening Refer to -15and FigurePreparation of Engine for Storage StorageNew Season Preparation Center Blade Spindle Lubrication PointsHours Left Blade SpindleFront Axle Center Pivot 100/M HoursGauge Wheel Bearing Zerk Deck Lift Pivot PointsSpecifications to continue on next Z44 & Z52 Accu-Z Razor Engine SpecificationsZ44 & Z52 Accu-Z Razor General Specifications Engine TypeDeck Housing Depth Brake ServiceSafety Features IndicatorsFor the operator Steering levers designed for Features BenefitsZ44 & Z52 Accu-Z Razor Park lever to OFF Hydro-Gear IZTEither direction Engine cranks but does not startEngine OverheatingHydraulic system operates hot Mower creeps when steering controlOne direction only Levers are in neutralAdditional Torque Values Torque Values ChartTire Inflation Chart In-tpiWarranty Belts, blades, and tires are considered wear itemsCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

357-044M specifications

The Land Pride 357-044M is a cutting-edge implement designed to meet the needs of professionals and enthusiasts in the agricultural sector. Known for its robust construction and innovative features, this attachment is ideal for enhancing productivity in various land management tasks.

One of the main features of the Land Pride 357-044M is its heavy-duty design, which is specifically built to withstand the rigors of daily use in demanding environments. The durable frame ensures longevity, allowing operators to tackle tough soil conditions without worrying about equipment failure. Additionally, the implement is equipped with high-quality materials that resist wear and tear, providing peace of mind for long-term reliability.

The 357-044M shines in its versatility. It can be used for a variety of applications, such as leveling ground, grading, and even snow removal in winter months. With adjustable features, operators can easily modify the attachment to suit specific job requirements, making it a multi-functional tool for land preparation.

Equipped with advanced technologies, the Land Pride 357-044M includes precision-engineered components that optimize performance. The attachment’s unique blade design enhances soil mixing and aeration, leading to improved crop yields. Furthermore, the implement's innovative hydraulic system allows for smooth and efficient operation, ensuring that the tool can be adapted to different tasks with minimal effort.

Operator comfort and efficiency are also key characteristics of the 357-044M. The implement features user-friendly controls, making it easy to operate even for those who may be unfamiliar with such equipment. The design takes into account ease of attachment and detachment from various tractors, promoting a seamless workflow on the job site.

In summary, the Land Pride 357-044M is a versatile and dependable implement that combines a robust design, innovative technologies, and operator-friendly features. Its ability to perform multiple tasks makes it an essential addition to any agricultural operation. With a focus on durability and efficiency, this attachment is sure to stand the test of time while delivering the performance that land management professionals demand.
Top Page Image Contents