Land Pride 357-044M manual Mower Deck Operation, General Operating Information, Blade

Page 20

Table of Contents

Section 2: Operating Procedures

Land Pride

Mower Deck Operation

!DANGER

Never attempt to make any adjustments to the mower deck while the engine is running or when the blades are engaged. Mower blades cannot be seen and are located very close to deck housing. Fingers and toes can be cut off instantly.

With the engine running at a medium speed, engage blades (Refer to Figure 2-11). Advance engine throttle to full rpm once the blades have become fully engaged.

NOTE: Engaging the blades at high engine rpm or when under heavy load (in tall grass for example) can cause belts to slip, resulting in premature wear or possible damage.

Blade

Engagement

Switch

23686

Blade Engagement Switch

Figure 2-11

General Operating Information

After thoroughly familiarizing yourself with the Operator’s Manual and completing the Operator’s Checklist, you are almost ready to begin mowing.

Approach the mower from the front. Spread the control levers fully apart if they aren’t already in the wide-open position and set the park lever to (ON). Taking care not to step on either side of the mower deck, step up on the operator’s platform and comfortably seat yourself. With both control levers still wide apart reach for the throttle and choke control to your right side. Position the throttle control at half throttle and pull the choke to the “up/on” position. Insert your ignition key and rotate the ignition key clockwise until you hear the engine begin to start. Release the ignition key and push the choke to “down/ off” position. Allow the engine to warm up momentarily. If your mower has just been running and the engine is already warm, using the choke is usually not necessary.

With the engine at half throttle, set the park lever in the (OFF) position and pull the control levers in to bring both control levers equally together in the neutral position just in front of you. It’s now time to test your steering skills.

Gently push both control levers equally forward. The farther forward you push the levers the faster you will go. Pull back equally and you will slow down coming to a stop when you reach the neutral position. Now slowly pull the levers back toward your body past neutral position. The mower will reverse direction and increase in speed as you pull further back. If you push one lever forward and pull one lever back the mower will do a Zero turn in the direction of the control lever closest to your body. Now take a few moments in a safe area to practice steering your mower with the engine still at half throttle. Gradually increase your throttle speed until you feel totally confident in your mower steering and handling ability.

After removing all obstacles from the lawn, it is now time to cut the grass. With your mower at half throttle, place your right foot on the deck lift pedal and release and lower the deck to your preset cutting height. With your right hand, pull up on the cutting blade engagement knob and increase the engine speed to full throttle. You may now begin mowing.

When you are done mowing or just want to take a break, make sure you:

•Park on level ground

•Disengage the cutting blades

•Throttle back

•Move the control levers to wide-open

•Set the park lever to (ON)

•Turn the engine off

•Remove the key

•Step carefully off the front of the machine.

18 Z44 & Z52 (S/N 472620 -526170) Zero Turning Radius Mowers Riding Mowers Accu-Z Razor® 357-044M

2/27/07

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Riding Mowers Accu-Z Razor Table of Contents Safety at All Times Avoid High Pressure Fluids Hazard Practice Safe MaintenanceKeep Riders Off Machinery Prepare for Emergencies Wear Protective Equipment838-303C 838-815C838-307C 838-308C 838-833C 838-310C 818-543C Owner Assistance Using This ManualApplication Control Lever Assembly Seat AssemblyHitch Plate Assembly Uncrating InstructionsRemove Mower From Crate Floor Electrical Cable ConnectionEngine Preparations Muffler Shield Is Located Under Engine Mower FeaturesRazor Features Land PrideTable of Contents Blade Engagement Switch Left/Right Fuel Tank ValveControl Levers Park LeverSafety Start Interlock System Deck Height Deck Lift Locking Pin Pedal IndicatorEngine Starting Deck Lift PedalDriving the Mower To Decrease Speed or StopTo Start and Increase Speed SteeringMoving Mower with Stalled Engine Front of Mower Faces This DirectionSteering Bypass Valve RodsSafe Operating Instructions Discharge Chute Blade Engagement Switch Mower Deck OperationGeneral Operating Information BladeTorque Values Steering LinkageTorque Values FT lbsControl Lever Neutral Adjustment Steering DampenerSeat Adjustment Upper Control Lever AdjustmentsHeight Adjustment Reach AdjustmentHydro-Drive Belt Adjustment Engine RPM SettingDeck Drive Belt Adjustment Deck Leveling & Height AdjustmentHeight Adjusting Stop Adjuster Bolt Jam Nut HardwareRefer to -9& Figure Refer to Figure Stop HandleLift Deck Lift Rod Adjustment Left Front Side ShownRefer to -10on Deck Cutting Height Adjustment Anti-Scalp RollersPivot Front Wheels Refer to -12onMaintenance Locations Deck Bottom View Drive motors removed for clarityMaintenance Schedule Service at Intervals Indicated Every Refer to HoursMaintenance Battery Wiring Harness FussesTires Electrical SystemAccess to IZT Units Integrated Zero-Turn Transaxle Hydraulic SystemHydraulic oil and Filter Refer to Refer to FigureFuel System Fuel Filter Draining The Fuel TankEngine Oil and Oil Filter Oil Check, Honda EngineGeneral Engine Maintenance Belt ReplacementDeck Belt Replacement Instructions Engine Air FilterMower Blade Maintenance Drive Belt Replacement InstructionsBlade Inspection Refer to -11onBlade Sharpening Refer to -15and FigureNew Season Preparation StoragePreparation of Engine for Storage Lubrication Points HoursCenter Blade Spindle Left Blade Spindle100/M Hours Gauge Wheel Bearing ZerkFront Axle Center Pivot Deck Lift Pivot PointsZ44 & Z52 Accu-Z Razor Engine Specifications Z44 & Z52 Accu-Z Razor General SpecificationsSpecifications to continue on next Engine TypeBrake Service Safety FeaturesDeck Housing Depth IndicatorsFeatures Benefits Z44 & Z52 Accu-Z RazorFor the operator Steering levers designed for Park lever to OFF Hydro-Gear IZTEngine cranks but does not start EngineEither direction OverheatingMower creeps when steering control One direction onlyHydraulic system operates hot Levers are in neutralTorque Values Chart Tire Inflation ChartAdditional Torque Values In-tpiWarranty Belts, blades, and tires are considered wear itemsCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

357-044M specifications

The Land Pride 357-044M is a cutting-edge implement designed to meet the needs of professionals and enthusiasts in the agricultural sector. Known for its robust construction and innovative features, this attachment is ideal for enhancing productivity in various land management tasks.

One of the main features of the Land Pride 357-044M is its heavy-duty design, which is specifically built to withstand the rigors of daily use in demanding environments. The durable frame ensures longevity, allowing operators to tackle tough soil conditions without worrying about equipment failure. Additionally, the implement is equipped with high-quality materials that resist wear and tear, providing peace of mind for long-term reliability.

The 357-044M shines in its versatility. It can be used for a variety of applications, such as leveling ground, grading, and even snow removal in winter months. With adjustable features, operators can easily modify the attachment to suit specific job requirements, making it a multi-functional tool for land preparation.

Equipped with advanced technologies, the Land Pride 357-044M includes precision-engineered components that optimize performance. The attachment’s unique blade design enhances soil mixing and aeration, leading to improved crop yields. Furthermore, the implement's innovative hydraulic system allows for smooth and efficient operation, ensuring that the tool can be adapted to different tasks with minimal effort.

Operator comfort and efficiency are also key characteristics of the 357-044M. The implement features user-friendly controls, making it easy to operate even for those who may be unfamiliar with such equipment. The design takes into account ease of attachment and detachment from various tractors, promoting a seamless workflow on the job site.

In summary, the Land Pride 357-044M is a versatile and dependable implement that combines a robust design, innovative technologies, and operator-friendly features. Its ability to perform multiple tasks makes it an essential addition to any agricultural operation. With a focus on durability and efficiency, this attachment is sure to stand the test of time while delivering the performance that land management professionals demand.
Top Page Image Contents