Preparation of Engine for Storage

Table of Contents

Section 4: Maintenance & Lubrication

Land Pride

Storage

Take the following steps when storing the mower at the end of the season and when the unit will not be used for long periods to ensure readiness for the next mowing season.

IMPORTANT: Do not use a high pressure washer on or around the IZT units. Water intrusion will result and void the IZT warranty.

1.Remove all grass, dirt, trash and grease that may have accumulated on the mower and moving parts.

2.Scrape off compacted dirt, trash and grass clippings from the deck underside. A coating of oil may also be applied to the deck underside to minimize oxidation.

3.Clean and touch up all scrapes with Land Pride spray paint.

4.Check blades and blade bolts for wear and replace if necessary.

5.Service air cleaner according to engine manufacture’s recommendations.

6.Check thoroughly for any worn or damaged parts that need replacing and order them from your nearest Land Pride Dealer.

7.Thoroughly lubricate machine, according to lubrication instructions.

8.Block mower up so weight is off tires.

NOTE: Do not deflate tires.

9.Protect battery from freezing temperatures. Disconnect the negative ground wire from the battery to reduce the chances of a slow electrical drain. Occasionally recharging battery during storage will extend battery life.

10.Prepare engine for storage as described below.

11.Store mower in a clean, dry place.

When engine is to be unused for long periods, proceed as follows:

1.Run engine for a minimum of 15 minutes.

2.Drain oil from crankcase while engine is still warm.

3.Refill with fresh oil of proper viscosity.

4.Drain fuel tank and run engine until it stops from lack of fuel. Gasoline evaporates if left in carburetor for long periods, forming gum and varnish deposits in carburetor. These deposits will cause engine flooding and loss of power.

5.Remove and replace fuel filter if not done in previous 100 hours.

6.Remove spark plugs and pour a tablespoon of engine oil into each spark plug hole. Install plugs, but do not reconnect plug leads.

7.Crank engine with starter at least a dozen revolutions to distribute oil over cylinder walls and valve mechanism.

8.Clean exterior surface of engine. Spread a light film of oil over any exposed metal surfaces of engine that are subject to corrosion.

9.Clean dirt and chaff from cylinders and fins, blower housing and muffler.

10.Check oil filler cap and fuel tank cap to make certain they are securely in place.

New Season Preparation

Before starting the mower following post season storage, the following servicing is required:

IMPORTANT: Do not use a high pressure washer on or around the IZT units. Water intrusion will result and void the IZT warranty.

1.Clean mower, removing trash and dirt accumulation.

2.Check engine oil level.

3.Tighten any bolts that have loosened and make sure all hair pins, cotter pins and clevis pins are in place.

4.Install all safety shields and review safety precautions listed in this manual.

5.Check and inflate tires to 8-12 psi.

6.Fill fuel tank with fresh gasoline.

7.Reconnect spark plug leads to spark plug.

8.Run machine at half speed for 5 minutes, checking operation of the control levers. Stop engine and check for oil leaks, loose fittings and so forth.

36 Z44 & Z52 (S/N 472620 -526170) Zero Turning Radius Mowers Riding Mowers Accu-Z Razor® 357-044M

2/27/07

357-044M specifications

The Land Pride 357-044M is a cutting-edge implement designed to meet the needs of professionals and enthusiasts in the agricultural sector. Known for its robust construction and innovative features, this attachment is ideal for enhancing productivity in various land management tasks.

One of the main features of the Land Pride 357-044M is its heavy-duty design, which is specifically built to withstand the rigors of daily use in demanding environments. The durable frame ensures longevity, allowing operators to tackle tough soil conditions without worrying about equipment failure. Additionally, the implement is equipped with high-quality materials that resist wear and tear, providing peace of mind for long-term reliability.

The 357-044M shines in its versatility. It can be used for a variety of applications, such as leveling ground, grading, and even snow removal in winter months. With adjustable features, operators can easily modify the attachment to suit specific job requirements, making it a multi-functional tool for land preparation.

Equipped with advanced technologies, the Land Pride 357-044M includes precision-engineered components that optimize performance. The attachment’s unique blade design enhances soil mixing and aeration, leading to improved crop yields. Furthermore, the implement's innovative hydraulic system allows for smooth and efficient operation, ensuring that the tool can be adapted to different tasks with minimal effort.

Operator comfort and efficiency are also key characteristics of the 357-044M. The implement features user-friendly controls, making it easy to operate even for those who may be unfamiliar with such equipment. The design takes into account ease of attachment and detachment from various tractors, promoting a seamless workflow on the job site.

In summary, the Land Pride 357-044M is a versatile and dependable implement that combines a robust design, innovative technologies, and operator-friendly features. Its ability to perform multiple tasks makes it an essential addition to any agricultural operation. With a focus on durability and efficiency, this attachment is sure to stand the test of time while delivering the performance that land management professionals demand.