Land Pride 357-044M manual Maintenance, Torque Values

Page 30

Table of Contents

Section 4: Maintenance & Lubrication

Land Pride

Maintenance

!WARNING

Read and observe all safety warnings in this manual and in the engine service manual.

!WARNING

Except when checking or changing components, always keep protective shields on for safety as well as for cleanliness.

!WARNING

Keep your machine clean and remove any deposits of trash and clippings, which can cause engine fires and hydraulic overheating as well as excessive belt wear.

!WARNING

DO NOT have engine running when servicing or making adjustments to the mower. Place control levers in the neutral position, disengage blade engagement, shut engine off and remove ignition switch key.

!DANGER

Repairs or maintenance specifically requiring engine power should be performed by trained personnel only. Control levers should be set in park position with the park lever set to (ON). If the control levers are to be operated, the tires should be properly supported off the floor. Enclosed areas should be properly ventilated to prevent carbon monoxide poisoning.

Regular maintenance is the best prevention for costly downtime or expensive, premature repair. The following pages contain suggested maintenance information and schedules which the operator should follow on a routine basis.

Check initially and periodically for loose bolts and pins. Torque loose bolts per the “Torque Values Chart” on page 44. Remain alert for unusual noises, they could be signaling a problem. Visually inspect the machine for any abnormal wear or damage. A good time to detect potential problems is while performing scheduled maintenance service. Correcting the problem as quickly as possible is the best insurance.

Clear away heavy build-up of grease, oil and dirt, especially in the engine and under the seat platform; minute dust particles are abrasive to close-tolerance engine and hydraulic assemblies.

Inspect mower daily for grass clippings, tangled wire and string. The underside of the mower deck will collect a build-up of grass clippings and dirt, especially when grass is wet or has high moisture content. This build-up will harden, restricting blade and air movement and will usually produce a poorer quality of cutting. Therefore, debris should be routinely removed from under the deck.

To do this it will be necessary to raise and block the deck in the full up position and scrape the build-up from underneath.

Some repairs require the assistance of a trained service mechanic and should not be attempted by unskilled personnel. Consult your Land Pride dealer when assistance is needed.

!WARNING

Before working on or under the deck, make certain the engine cannot be accidentally started. Shut engine off and remove ignition switch key for maximum safety. Repairs or maintenance requiring engine power should be performed by trained personnel only.

!DANGER

Exercise caution when working under the deck as the mower blades are extremely sharp. Wearing gloves is advisable when working around or with the blades.

!WARNING

When possible, clean under mower using a stick or similar instrument making sure that no part of the body, especially arms and hands are under mower.

IMPORTANT: The arm rests on the Deluxe Seat must be pivoted up before hinging the seat platform forward. Leaving the arm rests down while hinging the seat platform forward can cut the arm rest covers and void their warranty.

Torque Values

!WARNING

Particular attention must be given to tightening the drive wheel lug nuts, blade spindle bolts and electric clutch bolt. Failure to correctly torque these items may result in the loss of a wheel, blade or burnt clutch which can result in serious damage and/or personal injury.

It is recommended that the lug nuts, spindle bolts and electric clutch bolt be checked after the first 2 hours of initial operation and after removal for repair or replacement. Thereafter, they should be checked every 50 hours of operation. See Torque valves in chart below. For all other torques, see “Torque Values Chart” on page 44 and engine manual for engine torque values.

Torque Values

 

FT - lbs.

Nm

 

 

 

Wheel Lug Nuts

75

102

 

 

 

Spindle Housing

55

74

Flange Bolts

 

 

 

 

 

Electric Clutch Bolt

50 to 55

68 - 74

 

 

 

28 Z44 & Z52 (S/N 472620 -526170) Zero Turning Radius Mowers Riding Mowers Accu-Z Razor® 357-044M

2/27/07

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Riding Mowers Accu-Z Razor Table of Contents Safety at All Times Practice Safe Maintenance Keep Riders Off MachineryAvoid High Pressure Fluids Hazard Prepare for Emergencies Wear Protective Equipment838-303C 838-815C838-307C 838-308C 838-833C 838-310C 818-543C Using This Manual ApplicationOwner Assistance Hitch Plate Assembly Control Lever AssemblySeat Assembly Uncrating InstructionsElectrical Cable Connection Engine PreparationsRemove Mower From Crate Floor Mower Features Razor FeaturesMuffler Shield Is Located Under Engine Land PrideTable of Contents Control Levers Blade Engagement SwitchLeft/Right Fuel Tank Valve Park LeverEngine Starting Safety Start Interlock SystemDeck Height Deck Lift Locking Pin Pedal Indicator Deck Lift PedalTo Start and Increase Speed Driving the MowerTo Decrease Speed or Stop SteeringSteering Moving Mower with Stalled EngineFront of Mower Faces This Direction Bypass Valve RodsSafe Operating Instructions Discharge Chute General Operating Information Blade Engagement SwitchMower Deck Operation BladeTorque Values Torque ValuesSteering Linkage FT lbsControl Lever Neutral Adjustment Steering DampenerHeight Adjustment Seat AdjustmentUpper Control Lever Adjustments Reach AdjustmentDeck Drive Belt Adjustment Hydro-Drive Belt AdjustmentEngine RPM Setting Deck Leveling & Height AdjustmentRefer to -9& Figure Refer to Figure Height Adjusting StopAdjuster Bolt Jam Nut Hardware Stop HandleDeck Lift Rod Adjustment Left Front Side Shown Refer to -10onLift Pivot Front Wheels Deck Cutting Height AdjustmentAnti-Scalp Rollers Refer to -12onMaintenance Locations Deck Bottom View Drive motors removed for clarityMaintenance Schedule Service at Intervals Indicated Every Refer to HoursMaintenance Tires BatteryWiring Harness Fusses Electrical SystemHydraulic oil and Filter Access to IZT Units Integrated Zero-Turn TransaxleHydraulic System Refer to Refer to FigureFuel System Engine Oil and Oil Filter Fuel FilterDraining The Fuel Tank Oil Check, Honda EngineDeck Belt Replacement Instructions General Engine MaintenanceBelt Replacement Engine Air FilterBlade Inspection Mower Blade MaintenanceDrive Belt Replacement Instructions Refer to -11onBlade Sharpening Refer to -15and FigureStorage Preparation of Engine for StorageNew Season Preparation Center Blade Spindle Lubrication PointsHours Left Blade SpindleFront Axle Center Pivot 100/M HoursGauge Wheel Bearing Zerk Deck Lift Pivot PointsSpecifications to continue on next Z44 & Z52 Accu-Z Razor Engine SpecificationsZ44 & Z52 Accu-Z Razor General Specifications Engine TypeDeck Housing Depth Brake ServiceSafety Features IndicatorsFor the operator Steering levers designed for Features BenefitsZ44 & Z52 Accu-Z Razor Park lever to OFF Hydro-Gear IZTEither direction Engine cranks but does not startEngine OverheatingHydraulic system operates hot Mower creeps when steering controlOne direction only Levers are in neutralAdditional Torque Values Torque Values ChartTire Inflation Chart In-tpiWarranty Belts, blades, and tires are considered wear itemsCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

357-044M specifications

The Land Pride 357-044M is a cutting-edge implement designed to meet the needs of professionals and enthusiasts in the agricultural sector. Known for its robust construction and innovative features, this attachment is ideal for enhancing productivity in various land management tasks.

One of the main features of the Land Pride 357-044M is its heavy-duty design, which is specifically built to withstand the rigors of daily use in demanding environments. The durable frame ensures longevity, allowing operators to tackle tough soil conditions without worrying about equipment failure. Additionally, the implement is equipped with high-quality materials that resist wear and tear, providing peace of mind for long-term reliability.

The 357-044M shines in its versatility. It can be used for a variety of applications, such as leveling ground, grading, and even snow removal in winter months. With adjustable features, operators can easily modify the attachment to suit specific job requirements, making it a multi-functional tool for land preparation.

Equipped with advanced technologies, the Land Pride 357-044M includes precision-engineered components that optimize performance. The attachment’s unique blade design enhances soil mixing and aeration, leading to improved crop yields. Furthermore, the implement's innovative hydraulic system allows for smooth and efficient operation, ensuring that the tool can be adapted to different tasks with minimal effort.

Operator comfort and efficiency are also key characteristics of the 357-044M. The implement features user-friendly controls, making it easy to operate even for those who may be unfamiliar with such equipment. The design takes into account ease of attachment and detachment from various tractors, promoting a seamless workflow on the job site.

In summary, the Land Pride 357-044M is a versatile and dependable implement that combines a robust design, innovative technologies, and operator-friendly features. Its ability to perform multiple tasks makes it an essential addition to any agricultural operation. With a focus on durability and efficiency, this attachment is sure to stand the test of time while delivering the performance that land management professionals demand.
Top Page Image Contents