Land Pride 357-044M manual Hydraulic System, Hydraulic oil and Filter, Refer to Refer to Figure

Page 32

Table of Contents

Section 4: Maintenance & Lubrication

Refer to Figure 4-4:

!

WARNING

Remove the cover over the fuse to access the fuse.

 

 

Land Pride

Uncovered

20 Amp Fuse

23809

20amp Fuse W/Cover Removed

Figure 4-4

Before attempting any diagnosis of electrical system, use a test light or voltmeter to check battery voltage. If battery voltage is satisfactory, check cleanliness and tightness of terminals and ground connections. A general understanding of electrical servicing and use of basic test equipment is necessary for troubleshooting and repair.

Always wear adequate eye protection when servicing the hydraulic system and battery.

Hydraulic System

The Razor is equipped with Hydro-Gear IZT (Integrated Zero-Turn Transaxle) units. These units are self contained, except for changing oil and filters. Repair of an IZT unit should be performed by trained technicians only.

NOTE: The IZT units are equipped with bypass valves. For more information refer to “Moving Mower with Stalled Engine” on page 15.

IMPORTANT: Do not use a high pressure washer on or around the IZT units. Water intrusion will result and void the IZT warranty.

Hydraulic oil and Filter

Major overhaul or repair of starting motor or alternator should be performed by trained technicians only.

Access to IZT Units

(Integrated Zero-Turn Transaxle)

Refer to Refer to Figure 4-5

The IZT units are accessed by lifting the seat platform which is hinged at the front. To raise it, remove two bolts and tilt the seat platform up and forward.

NOTE: If the seat is equipped with the optional arm rest kit, make certain to place the control arms in the park position, set park lever to (ON) and pivot the arm rests upward before tilting the seat platform.

Bolts

23643

Access to IZT Units

Figure 4-5

Refer to Figure 4-6:

Initially change hydraulic oil and oil filter after the first 50 hours of operation. Thereafter, change the hydraulic oil and oil filter every 200 hours or every 2 years whichever comes first. Filter replacement kit #356-552A may be purchased from your nearest Land Pride dealer. The Kit contains two filters and two magnetic plugs.

Change hydraulic oil and oil filter as follows:

1.Raise mower so that filter and 9/16” magnetic plug can be accessed and worked on in a safe manner.

2.Place oil pan beneath pump.

Magnetic Plug

Oil Filter

23692

Access to Oil Filter and Magnetic Plug

Figure 4-6

30 Z44 & Z52 (S/N 472620 -526170) Zero Turning Radius Mowers Riding Mowers Accu-Z Razor® 357-044M

2/27/07

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Riding Mowers Accu-Z Razor Table of Contents Safety at All Times Avoid High Pressure Fluids Hazard Practice Safe MaintenanceKeep Riders Off Machinery Prepare for Emergencies Wear Protective Equipment838-303C 838-815C838-307C 838-308C 838-833C 838-310C 818-543C Owner Assistance Using This ManualApplication Control Lever Assembly Seat AssemblyHitch Plate Assembly Uncrating InstructionsRemove Mower From Crate Floor Electrical Cable ConnectionEngine Preparations Muffler Shield Is Located Under Engine Mower FeaturesRazor Features Land PrideTable of Contents Blade Engagement Switch Left/Right Fuel Tank ValveControl Levers Park LeverSafety Start Interlock System Deck Height Deck Lift Locking Pin Pedal IndicatorEngine Starting Deck Lift PedalDriving the Mower To Decrease Speed or StopTo Start and Increase Speed SteeringMoving Mower with Stalled Engine Front of Mower Faces This DirectionSteering Bypass Valve RodsSafe Operating Instructions Discharge Chute Blade Engagement Switch Mower Deck OperationGeneral Operating Information BladeTorque Values Steering LinkageTorque Values FT lbsControl Lever Neutral Adjustment Steering DampenerSeat Adjustment Upper Control Lever AdjustmentsHeight Adjustment Reach AdjustmentHydro-Drive Belt Adjustment Engine RPM SettingDeck Drive Belt Adjustment Deck Leveling & Height AdjustmentHeight Adjusting Stop Adjuster Bolt Jam Nut HardwareRefer to -9& Figure Refer to Figure Stop HandleLift Deck Lift Rod Adjustment Left Front Side ShownRefer to -10on Deck Cutting Height Adjustment Anti-Scalp RollersPivot Front Wheels Refer to -12onMaintenance Locations Deck Bottom View Drive motors removed for clarityMaintenance Schedule Service at Intervals Indicated Every Refer to HoursMaintenance Battery Wiring Harness FussesTires Electrical SystemAccess to IZT Units Integrated Zero-Turn Transaxle Hydraulic SystemHydraulic oil and Filter Refer to Refer to FigureFuel System Fuel Filter Draining The Fuel TankEngine Oil and Oil Filter Oil Check, Honda EngineGeneral Engine Maintenance Belt ReplacementDeck Belt Replacement Instructions Engine Air FilterMower Blade Maintenance Drive Belt Replacement InstructionsBlade Inspection Refer to -11onBlade Sharpening Refer to -15and FigureNew Season Preparation StoragePreparation of Engine for Storage Lubrication Points HoursCenter Blade Spindle Left Blade Spindle100/M Hours Gauge Wheel Bearing ZerkFront Axle Center Pivot Deck Lift Pivot PointsZ44 & Z52 Accu-Z Razor Engine Specifications Z44 & Z52 Accu-Z Razor General SpecificationsSpecifications to continue on next Engine TypeBrake Service Safety FeaturesDeck Housing Depth IndicatorsFeatures Benefits Z44 & Z52 Accu-Z RazorFor the operator Steering levers designed for Park lever to OFF Hydro-Gear IZTEngine cranks but does not start EngineEither direction OverheatingMower creeps when steering control One direction onlyHydraulic system operates hot Levers are in neutralTorque Values Chart Tire Inflation ChartAdditional Torque Values In-tpiWarranty Belts, blades, and tires are considered wear itemsCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

357-044M specifications

The Land Pride 357-044M is a cutting-edge implement designed to meet the needs of professionals and enthusiasts in the agricultural sector. Known for its robust construction and innovative features, this attachment is ideal for enhancing productivity in various land management tasks.

One of the main features of the Land Pride 357-044M is its heavy-duty design, which is specifically built to withstand the rigors of daily use in demanding environments. The durable frame ensures longevity, allowing operators to tackle tough soil conditions without worrying about equipment failure. Additionally, the implement is equipped with high-quality materials that resist wear and tear, providing peace of mind for long-term reliability.

The 357-044M shines in its versatility. It can be used for a variety of applications, such as leveling ground, grading, and even snow removal in winter months. With adjustable features, operators can easily modify the attachment to suit specific job requirements, making it a multi-functional tool for land preparation.

Equipped with advanced technologies, the Land Pride 357-044M includes precision-engineered components that optimize performance. The attachment’s unique blade design enhances soil mixing and aeration, leading to improved crop yields. Furthermore, the implement's innovative hydraulic system allows for smooth and efficient operation, ensuring that the tool can be adapted to different tasks with minimal effort.

Operator comfort and efficiency are also key characteristics of the 357-044M. The implement features user-friendly controls, making it easy to operate even for those who may be unfamiliar with such equipment. The design takes into account ease of attachment and detachment from various tractors, promoting a seamless workflow on the job site.

In summary, the Land Pride 357-044M is a versatile and dependable implement that combines a robust design, innovative technologies, and operator-friendly features. Its ability to perform multiple tasks makes it an essential addition to any agricultural operation. With a focus on durability and efficiency, this attachment is sure to stand the test of time while delivering the performance that land management professionals demand.
Top Page Image Contents