Generac Power Systems 5253, 5252, 5254, 5251, 5255 owner manual Sheet Metal PAINT/MATERIAL Code Legend

Page 44

Section 9 — Exploded Views and Parts Lists

Air-cooled Generators

Enclosure – Drawing No. 0F9431-C

SHEET METAL PAINT/MATERIAL CODE LEGEND

The following exploded views contain part numbers of various sheet metal components. Only the base part number is listed. When ordering sheet metal, the correct color and material information must be included as a sufﬁ x at the end of the part number as shown below.

Material	Color	Example:	Desc.	Part No.	Material	Color	Order As"
S = Steel	N = Tan		Roof	0F6522	S = Steel	N = Tan	0F6522SN
A = Aluminum	G = Gray		Door	0F6555	A = Aluminum	G = Gray	0F6555AG
	B = Black		Divider	0F6558	S = Steel	B = Black	0F6558SB

42

Image 44

Contents Listed Introduction Authorized Dealer LocationPost Installation Start-up Adjustments MaintenanceTroubleshooting Introduction Inside Front Cover Warning   Electrical Hazards  ‹ Standards IndexBreaker for Bedrooms UNPACKING/INSPECTIONProtection Systems Generator 7kW, Single Cylinder GH-410 Engine‹ 1.5.2 Engine Specifications‹ 1.5.1 Generator System SET LED Fuel Requirements RecommendationsFuel Consumption ‹ 1.8.1 BTU Flow Requirements Natural GAS‹ 1.9.2 10, 13 and 16KW, V-TWIN Engines Reconfiguring the Fuel System‹ 1.9.1 7 KW, 410CC Engine Location ‹ 1.10.1 GeneratorBattery Requirements Battery Installation‹ 1.10.2 Transfer Switch 10.2.1 7, 10, 13, and 16 kW Units if equippedBattery 10 Battery Cable ConnectionsElectrical Checks Check Transfer Switch OperationBefore Initial START-UP 7KW Natural GAS only Generator Tests Under LoadChecking Automatic Operation Engine Governor Adjustment ‹ 2.7.1 7 KW Units‹ 3.1.1 Auto Position ‹ 3.1.3 Manual PositionAutomatic Transfer Operation Sequence of Automatic OperationManual Transfer Operation ‹ 3.1.4 Choke OperationSetting the Exercise Timer ‹ 3.4.2 Transfer Back to Utility Power Source‹ 3.6.1 LOW OIL Pressure Switch ‹ 3.6.2 High Temperature Switch‹ 3.6.3 Overcrank Approximate Crank Cycle Times‹ 3.6.6 LOW Battery Checking the Engine OIL LevelFuses ‹ 3.6.5 RPM Sensor Failure‹ 4.3.2 Engine OIL Recommendations Changing the Engine OIL‹ 4.3.1 OIL Change Intervals ‹ 4.4.2 10KW Generators Spark Plugs‹ 4.4.1 7, 13, and 16KW Generators Battery Maintenance Valve ClearanceCooling System 11 Cooling Vent LocationsOUT of Service Procedure ‹ 4.11.2 Return to Service‹ 4.11.1 Removal from Service Corrosion ProtectionService Schedule Be performed by the nearest Authorized DealerTroubleshooting Guide Problem Cause CorrectionAir-cooled Generators Air-cooled Generators Air-cooled Generators Mounting Dimensions Electrical Data Engine Wiring Customer Connection Battery Charger Engine Alternator Engine Wiring Stator Electronic Voltage Regulator Manual Auto Scsm Neutral Electrical Data Electrical Data Sheet Metal PAINT/MATERIAL Code Legend Part NO. QTY. Description Air-cooled Generators Control Panel Drawing No F9695-C QTY Description Exploded Views and Parts Lists BOX Load Center Exploded Views and Parts Lists Description QTY Exploded Views and Parts Lists Washer Flat M8 5/16 Exploded Views and Parts Lists Crankcase Exploded Views and Parts Lists Intake Adapter Exploded Views and Parts Lists PIN, Piston D20 Exploded Views and Parts Lists SCREW, Taptite M6-1.0X8 Yellow Chrome Air-cooled Generators 7kW, GN-410 Engine Drawing No F9422-B ADAPTOR, Engine Exploded Views and Parts Lists ADATOR, Engine 7KW CASTING, Twin Regulator Housing 7KW Exploded Views and Parts Lists Brkt Regulator Mounting PURCHASER’S/OWNER’S Warranty Responsibilities Your Warranty Rights and ObligationsMANUFACTURER’S Emission Control System Warranty Coverage Emission Control System Warranty Emission Related Parts Include the FollowingGenerac Power Systems Standard Limited Warranty for